Self-passivating carbon film as bipolar plate protective coating in polymer electrolyte membrane fuel cell

2016 ◽  
Vol 41 (13) ◽  
pp. 5783-5792 ◽  
Author(s):  
Zhiyuan Wang ◽  
Kai Feng ◽  
Zhuguo Li ◽  
Fenggui Lu ◽  
Jian Huang ◽  
...  
Keyword(s):  
Fuel Cell ◽  
Polymer Electrolyte ◽  
Protective Coating ◽  
Polymer Electrolyte Membrane ◽  
Carbon Film ◽  
Bipolar Plate ◽  
Electrolyte Membrane

Preparation of Polymer Composite Bipolar Plate with Different Multi-Filler for Polymer Electrolyte Membrane Fuel Cell (PEMFC)

2014 ◽  
Vol 699 ◽  
pp. 689-694 ◽  
Author(s):  
Mohd Zulkefli Selamat ◽  
Mohd Shakir Ahmad ◽  
Mohd Ahadlin Mohd Daud ◽  
Musthafa Mohd Tahir ◽  
Safaruddin Gazali Herawan
Keyword(s):  
Electrical Conductivity ◽  
Fuel Cell ◽  
Polymer Electrolyte ◽  
Alternative Energy ◽  
Polymer Electrolyte Membrane ◽  
Energy System ◽  
Bipolar Plate ◽  
Filler Loading ◽  
Shore Hardness ◽  
Electrolyte Membrane

Polymer Electrolyte Membrane Fuel Cell (PEMFC) is an alternative energy system that has been verified with great potential for high power density, durability and cost effectiveness. Since the bipolar plate is the key component in PEMFC, the component must operate with multifunction and have a balance of properties, essentially well in both electrical and mechanical properties. At present, many different materials have been tested to be applied for bipolar plate in order to fulfill the balance in each property. In this work, the different material is tested and observed. Polypropylene (PP) is used as a binder material, Graphite (Gr) is used as a main filler and Carbon Black (CB), Iron (Fe) and Nickel (Ni) as the second filler. This composite is produced through compression molding and the effect of different filler material loading on the properties such as electrical conductivity, flexural strength, bulk density and shore hardness are observed. The result showed the increasing of electrical conductivity as the increased the CB and Fe loading. But for Ni, the result showed the decreasing of electrical conductivity as the loading of Ni has been increased. The targeted value also achieved for some certain degree of filler loading.

Preparation of Multi-Layer Film on Stainless Steel as Bipolar Plate for Polymer Electrolyte Membrane Fuel Cell

2010 ◽  
Vol 113-116 ◽  
pp. 2255-2261
Author(s):  
Dong Ming Zhang ◽  
Lu Guo ◽  
Liang Tao Duan ◽  
Zai Yi Wang
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Fuel Cell ◽  
Polymer Electrolyte ◽  
Polymer Electrolyte Membrane ◽  
Electrical Conductance ◽  
Bipolar Plate ◽  
Contact Angles ◽  
Water Contact ◽  
Electrolyte Membrane

In the present study, we try to prepare hydrophobic film coated on stainless steel as the bipolar plate for polymer electrolyte membrane fuel cell (PEMFC). Magnetron sputtering (MS) was adoped to prepare the Cr3Ni2/Cr2N multi-layer coated on stainless steel. The corrosion resistance and electrical conductance of the coated substrate were tested. The water contact angles were measured. The film exhibits improved corrosion resistance and electrical conductance. The corrosion current is 0.58µA.cm-2 and the contact resistance at 240N.cm-2 is 8.5mΩ.cm2. Meanwhile, it is a kind of hydrophobic film with water contact angle of 107o. The performance shows strong dependance on microstructural characteristics. The nano-protrudes on the SS304/Cr3Ni2/Cr2N surface result in the film with hydrophobic property, just like the effect of lotus surface.

Sign in / Sign up

Export Citation Format

Share Document