Evaluation for tool flank wear and its influences on surface roughness in ultra-precision raster fly cutting

2016 ◽  
Vol 118 ◽  
pp. 125-134 ◽  
Author(s):  
Guoqing Zhang ◽  
Suet To ◽  
Shaojian Zhang
Keyword(s):  
Surface Roughness ◽  
Flank Wear ◽  
Tool Flank Wear ◽  
Fly Cutting ◽  
Ultra Precision

Study on the influence of spindle vibration on the surface roughness of ultra-precision fly cutting

2020 ◽  
Vol 16 (3) ◽  
pp. 258
Author(s):  
Bin Li ◽  
Zexiang Zhao ◽  
Huiying Zhao ◽  
Dongxu Ren ◽  
Jianpu Xi
Keyword(s):  
Surface Roughness ◽  
Fly Cutting ◽  
Ultra Precision ◽  
Spindle Vibration

Study on Tool Life of Surface Textured Tool in Dry Cutting of Ti-6Al-4V Alloys

2012 ◽  
Vol 538-541 ◽  
pp. 1245-1249 ◽  
Author(s):  
Ze Wu ◽  
Jian Xin Deng ◽  
Jun Zhao
Keyword(s):  
Surface Roughness ◽  
Laser Beam ◽  
Tool Life ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Dry Cutting ◽  
Laser Beam Machining ◽  
Tool Flank Wear

Surface textured tools were fabricated by laser beam machining. Dry cutting of Ti-6Al-4V alloys was carried out with these surface textured tools and conventional tools for comparison. The cutting temperature, tool flank wear and surface roughness of processed workpiece were measured. The experimental formulas of tool life based on DOT method were developed. Results show that the surface textured tool can reduce the surface roughness of workpiece, and the tool life of surface textured tool is improved by 15% or so compared with the conventional one.

scholarly journals Effects of Tool Wear on Machined Surface Integrity During Milling of Inconel 718

2021 ◽  
Author(s):  
Liang Tan ◽  
Changfeng Yao ◽  
Dinghua Zhang ◽  
Minchao Cui ◽  
Xuehong Shen
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Tool Wear ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Machined Surface ◽  
Tool Flank Wear ◽  
Machined Surface Integrity

Abstract This paper investigates the effects of tool wear on the machined surface integrity characteristics, including the surface roughness, surface topography, residual stress, microhardness and microstructure, during ball-end milling of Inconel 718. Tool wear, tool lifetime, and cutting force are measured. In addition, a two-dimensional finite element-based model is developed to investigate the cutting temperature distribution in the chip–tool–workpiece contact area. Results show that the ball nose end mill achieves tool lifetime of approximately 350 min. The cutting forces increase sharply with a greater tool flank wear width, while the highest cutting temperature has a decreasing tend at a flank wear width of 0.3 mm. Higher tool flank wear width produces larger surface roughness and deteriorative surface topography. A high-amplitude (approximately −700 MPa) and deep layer (approximately 120 mm) of compressive residual stress are induced by a worn tool with 0.3 mm flank wear width. The surface microhardness induced by new tool is larger than that induced by worn tool. Plastic deformation and strain streamlines are observed within 10 mm depth beneath the surface. The results in this paper provide an optimal tool wear criterion which integrates the surface integrity requirements and the tool lifetime for ball-end finish milling of Inconel 718.

Study on the influence of spindle vibration on the surface roughness of ultra-precision fly cutting

2020 ◽  
Vol 16 (3) ◽  
pp. 258
Author(s):  
Jianpu Xi ◽  
Bin Li ◽  
Dongxu Ren ◽  
Zexiang Zhao ◽  
Huiying Zhao
Keyword(s):  
Surface Roughness ◽  
Fly Cutting ◽  
Ultra Precision ◽  
Spindle Vibration

Comparative Evaluation of Performances of TiAlN-, AlCrN- and AlCrN/TiAlN-Coated Carbide Cutting Tools and Uncoated Carbide Cutting Tools on Turning EN24 Alloy Steel

2017 ◽  
Vol 16 (03) ◽  
pp. 237-261 ◽  
Author(s):  
T. Sampath Kumar ◽  
S. Balasivanandha Prabu ◽  
T. Sorna Kumar
Keyword(s):  
Surface Roughness ◽  
Alloy Steel ◽  
Surface Finish ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Tool Flank Wear ◽  
Coated Carbide

In the present work, the performances of TiAlN-, AlCrN- and AlCrN/TiAlN-coated and uncoated tungsten carbide cutting tool inserts are evaluated from the turning studies conducted on EN24 alloy steel workpiece. The output parameters such as cutting forces, surface roughness and tool wear for TiAlN-, AlCrN- and AlCrN/TiAlN-coated carbide cutting tools are compared with uncoated carbide cutting tools (K10). The design of experiment based on Taguchi’s approach is used to obtain the best turning parameters, namely cutting speed ([Formula: see text]), feed rate ([Formula: see text]) and depth of cut ([Formula: see text]), in order to have a better surface finish and minimum tool flank wear. An orthogonal array (L[Formula: see text] was used to conduct the experiments. The results show that the AlCrN/TiAlN-coated cutting tool provided a much better surface finish and minimum tool flank wear. The minimum tool flank wear and minimum surface roughness were obtained using AlCrN/TiAlN-coated tools, when [Formula: see text][Formula: see text]m/min, [Formula: see text][Formula: see text]mm/rev and [Formula: see text][Formula: see text]mm.

scholarly journals Optimizing Multi-Response Parameters in Turning of AISI1040 Steel Using Desirability Approach

2019 ◽  
Vol 4 (4) ◽  
pp. 905-921
Author(s):  
Srinu Gugulothu ◽  
Vamsi Krishna Pasam
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Flank Wear ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Tool Flank Wear ◽  
Multi Objective ◽  
Single Objective

In this study, an attempt is made to examine the machining response parameters in turning of AISI 1040 steel under different lubrication environment. Subsequently, design of experiment technique Response surface methodology (RSM) is used for analyzing machining performance by varying cutting conditions with the use of 2wt% of CNT/MoS2(1:2) HNCF. Regression models are developed for multiple machining responses. Optimization is performed for these models by using desirability function, which converts multi-objective into single objective. Then the optimal setting parameters for single objective is found. Significant reduction in main cutting force (Fz), cutting temperature (T), surface roughness(Ra) and tool flank wear (Vb) are found with the use of 2wt% of CNT/MoS2(1:2) HNCF compared to other lubrication environment. Significant factors that affect the main cutting force (Fz), the temperature in the cutting zone are cutting speed, feed rate and depth of cut. Parameter depth of cut has an insignificant effect on tool flank wear and surface roughness (Ra). The optimal cutting conditions for four multi-objective optimization of main cutting force (Fz), cutting temperature, surface roughness (Ra) and tool flank wear are found to be cutting speed 70.25 m/min, feed 0.13 mm/rev and doc 0.5mm at desirability value of 0.907.

Sign in / Sign up

Export Citation Format

Share Document