A novel transient infrared-thermography based experimental method for the inverse estimation of heat transfer coefficients in rotating bearings

2021 ◽  
Vol 167 ◽  
pp. 107000
Author(s):  
T. Helmig ◽  
R. Kneer
Keyword(s):  
Heat Transfer ◽  
Experimental Method ◽  
Infrared Thermography ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Inverse Estimation

Heat Transfer Measurements in an Internal Cooling System Using a Transient Technique With Infrared Thermography

2012 ◽  
Author(s):  
Christian Egger ◽  
Jens von Wolfersdorf ◽  
Martin Schnieder
Keyword(s):  
Heat Transfer ◽  
Data Analysis ◽  
Infrared Thermography ◽  
Outer Surface ◽  
Cooling System ◽  
Internal Cooling ◽  
Test Model ◽  
Cooling Channel ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

In this paper a transient method for measuring heat transfer coefficients in internal cooling systems using infrared thermography is applied. The experiments are performed with a two-pass internal cooling channel connected by a 180° bend. The leading edge and the trailing edge consist of trapezoidal and nearly rectangular cross sections, respectively, to achieve an engine-similar configuration. Within the channels rib arrangements are considered for heat transfer enhancement. The test model is made of metallic material. During the experiment the cooling channels are heated by the internal flow. The surface temperature response of the cooling channel walls is measured on the outer surface by infrared thermography. Additionally, fluid temperatures as well as fluid and solid properties are determined for the data analysis. The method for determining the distribution of internal heat transfer coefficients is based on a lumped capacitance approach which considers lateral conduction in the cooling system walls as well as natural convection and radiation heat transfer on the outer surface. Because of time-dependent effects a sensitivity analysis is performed to identify optimal time periods for data analysis. Results are compared with available literature data.

Investigation of Buoyancy Effects in Asymmetrically Heated Near-Critical Flows of Carbon Dioxide in Horizontal Microchannels Using Infrared Thermography

2021 ◽  
Author(s):  
Lindsey V. Randle ◽  
Brian M. Fronk
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Heat Flux ◽  
Infrared Thermography ◽  
Test Section ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Parallel Microchannels

Abstract In this study, we use infrared thermography to calculate local heat transfer coefficients of top and bottom heated flows of near-critical carbon dioxide in an array of parallel microchannels. These data are used to evaluate the relative importance of buoyancy for different flow arrangements. A Joule heated thin wall made of Inconel 718 applies a uniform heat flux either above or below the horizontal flow. A Torlon PAI test section consists of three parallel microchannels with a hydraulic diameter of 923 μm. The reduced inlet temperature (TR = 1.006) and reduced pressure (PR = 1.03) are held constant. For each heater orientation, the mass flux (520 kgm−2s−2 ≤ G ≤ 800 kgm−2s−2) and heat flux (4.7 Wcm−2 ≤ q″ ≤ 11.1 Wcm−2) are varied. A 2D resistance network analysis method calculates the bulk temperatures and heat transfer coefficients. In this analysis, we divide the test section into approximately 250 segments along the stream-wise direction. We then calculate the bulk temperatures using the enthalpy from the upstream segment, the heat flux in a segment, and the pressure. To isolate the effect of buoyancy, we screen the data to omit conditions where flow acceleration may be important or where relaminarization may occur. In the developed region of the channel, there was a 10 to 15 percent reduction of the local heat transfer coefficients for the upward heating mode compared to downward heating with the same mass and heat fluxes. Thus buoyancy effects should be considered when developing correlations for these types of flow.

Heat Transfer Measurements in an Internal Cooling System Using a Transient Technique With Infrared Thermography

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Christian Egger ◽  
Jens von Wolfersdorf ◽  
Martin Schnieder
Keyword(s):  
Heat Transfer ◽  
Data Analysis ◽  
Infrared Thermography ◽  
Outer Surface ◽  
Cooling System ◽  
Internal Cooling ◽  
Test Model ◽  
Cooling Channel ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

In this paper, a transient method for measuring heat transfer coefficients in internal cooling systems using infrared thermography is applied. The experiments are performed with a two-pass internal cooling channel connected by a 180 deg bend. The leading edge and the trailing edge consist of trapezoidal and nearly rectangular cross-sections, respectively, to achieve an engine-similar configuration. Within the channels, rib arrangements are considered for heat transfer enhancement. The test model is made of metallic material. During the experiment, the cooling channels are heated by the internal flow. The surface temperature response of the cooling channel walls is measured on the outer surface by infrared thermography. Additionally, fluid temperatures as well as fluid and solid properties are determined for the data analysis. The method for determining the distribution of internal heat transfer coefficients is based on a lumped capacitance approach, which considers lateral conduction in the cooling system walls as well as natural convection and radiation heat transfer on the outer surface. Because of time-dependent effects, a sensitivity analysis is performed to identify optimal time periods for data analysis. Results are compared with available literature data.

Sign in / Sign up

Export Citation Format

Share Document