A two-stage improved genetic algorithm-particle swarm optimization algorithm for optimizing the pressurization scheme of coal bed methane gathering networks

2019 ◽  
Vol 229 ◽  
pp. 941-955 ◽  
Author(s):  
Taicheng Zheng ◽  
Yongtu Liang ◽  
Bohong Wang ◽  
Hansen Sun ◽  
Jianqin Zheng ◽  
...  
Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2873 ◽  
Author(s):  
Dinh Thanh Viet ◽  
Vo Van Phuong ◽  
Minh Quan Duong ◽  
Quoc Tuan Tran

As sources of conventional energy are alarmingly being depleted, leveraging renewable energy sources, especially wind power, has been increasingly important in the electricity market to meet growing global demands for energy. However, the uncertainty in weather factors can cause large errors in wind power forecasts, raising the cost of power reservation in the power system and significantly impacting ancillary services in the electricity market. In pursuance of a higher accuracy level in wind power forecasting, this paper proposes a double-optimization approach to developing a tool for forecasting wind power generation output in the short term, using two novel models that combine an artificial neural network with the particle swarm optimization algorithm and genetic algorithm. In these models, a first particle swarm optimization algorithm is used to adjust the neural network parameters to improve accuracy. Next, the genetic algorithm or another particle swarm optimization is applied to adjust the parameters of the first particle swarm optimization algorithm to enhance the accuracy of the forecasting results. The models were tested with actual data collected from the Tuy Phong wind power plant in Binh Thuan Province, Vietnam. The testing showed improved accuracy and that this model can be widely implemented at other wind farms.


2017 ◽  
Vol 14 (8) ◽  
pp. 694-702 ◽  
Author(s):  
Mingxuan Mao ◽  
Li Zhang ◽  
Qichang Duan ◽  
O.J.K Oghorada ◽  
Pan Duan ◽  
...  

Author(s):  
K. Manjunath ◽  
T. Rangaswamy

In this paper an attempt has been made to optimize ply stacking sequence of single piece E-Glass/Epoxy, HM Carbon/Epoxy and Boron/Epoxy composite drive shafts using particle swarm optimization (PSOA). PSOA programme is developed using MATLAB V 7 to optimize the ply stacking sequence with an objective of weight minimization. The weight savings of the E-Glass/Epoxy, HM Carbon/Epoxy and Boron/Epoxy shaft are 51%, 87% and 85% of the steel shaft respectively. The optimum results of PSOA obtained are compared with results of genetic algorithm (GA) and found that PSOA yields better results than GA.


2019 ◽  
Vol 30 (8) ◽  
pp. 1263-1275 ◽  
Author(s):  
Quan Zhang ◽  
Yichong Dong ◽  
Yan Peng ◽  
Jun Luo ◽  
Shaorong Xie ◽  
...  

The hysteresis characteristics, which commonly existed in smart materials–based actuators, play a significant role in precision control technology. In this article, a modified Bouc–Wen model which can describe the asymmetric hysteresis characteristics of piezoelectric ceramic actuators is investigated. The corresponding parameters of the modified Bouc–Wen hysteresis model are identified through a genetic algorithm–based particle swarm optimization algorithm. Compared with independent particle swarm optimization method which is easily trapped in the local extremum, the proposed genetic algorithm–based particle swarm optimization features the strong searching ability both in early global search period and the later local search period. The experimental results show that the asymmetric Bouc–Wen model identified via genetic algorithm–based particle swarm optimization algorithm are more accurate than that identified through independent particle swarm optimization or genetic algorithm approach, and the maximum displacement error and the maximum relative error between the genetic algorithm–based particle swarm optimization model and the experimental value are 0.20 µm and 14.28%, respectively, which are much smaller than that of particle swarm optimization method with 0.67 µm and 47.85% and genetic algorithm method with 0.35 µm and 25%. In order to further verify the accuracy of the identified model, the hysteresis compensation of piezoelectric ceramic actuator was realized using the feedforward controller based on the inverse Bouc–Wen model.


Sign in / Sign up

Export Citation Format

Share Document