A study of high strength steels undergoing non-linear strain paths—Experiments and modelling

2011 ◽  
Vol 211 (1) ◽  
pp. 122-132 ◽  
Author(s):  
Rikard Larsson ◽  
Oscar Björklund ◽  
Larsgunnar Nilsson ◽  
Kjell Simonsson
Keyword(s):  
High Strength Steels ◽  
High Strength ◽  
Linear Strain ◽  
Non Linear ◽  
Strain Paths

Influence of Different Pre-Stretching Modes on the Forming Limit Diagram of AA6014

2012 ◽  
Vol 504-506 ◽  
pp. 71-76 ◽  
Author(s):  
Alexandra Werber ◽  
Mathias Liewald ◽  
Winfried Nester ◽  
Martin Grünbaum ◽  
Klaus Wiegand ◽  
...  
Keyword(s):  
Plane Strain ◽  
Biaxial Loading ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Linear Strain ◽  
Forming Limits ◽  
Systematic Analysis ◽  
Measurement Systems ◽  
Non Linear ◽  
Strain Paths

In order to evaluate the formability of sheet materials forming limit diagrams (FLD) are recorded which represent the values of major and minor strain when necking occurs. FLDs are recorded based on the assumption that exclusively linear strain paths occur. In real forming parts, however, particularly in those with complex shapes, predominantly non-linear strain paths occur which reduce the accuracy of the failure prediction according to a conventional FLD. For this reason forming limits after loading with non-linear strain paths have to be investigated. In this contribution a systematic analysis of the forming limits of a conventional AA6014 alloy after loading with non-linear strain paths is presented. This material is pre-stretched in uniaxial, plane strain and biaxial direction up to several levels before performing Nakajima experiments in order to determine FLDs. During the pre-stretching process as well as during the Nakajima experiment the strain distribution can be measured online very precisely with the optical deformation measurement systems GOM Aramis or VIALUX. The gained curves are compared to the FLD of the as-received material. The results prove a significant influence of the pre-stretching condition on the forming limits of the used aluminum alloy. For a low pre-stretching in uniaxial as well as in biaxial direction the FLDs show a slightly reduced formability while after higher pre-stretching levels the forming limit can be improved such as for biaxial loading after uniaxial pre-stretching. The formability after pre-stretching in plane strain direction was changed. Also, a shift of the FLD depending on the direction of pre-stretching can be observed.

Effect of Strain Paths on Formability Evaluation of TRIP Steels

2010 ◽  
Vol 89-91 ◽  
pp. 214-219 ◽  
Author(s):  
David Gutiérrez ◽  
A. Lara ◽  
Daniel Casellas ◽  
Jose Manuel Prado
Keyword(s):  
Strain Path ◽  
High Strength Steels ◽  
High Strength ◽  
Test Method ◽  
Forming Limit ◽  
Trip Steels ◽  
Advanced High Strength Steels ◽  
Strain Paths ◽  
Analysis System

The Forming Limit Diagrams (FLD) are widely used in the formability analysis of sheet metal to determine the maximum strain, which gives the Forming Limit Curve (FLC). It is well known that these curves depend on the strain path during forming and hence on the test method used to calculate them. In this paper, different stretching tests such as the Nakajima and the Marciniak tests were performed, with different sample geometries to obtain points in different areas of the FLD. An optical analysis system was used, which allows following the strain path during the test. The increasing use of advanced high-strength steels (AHSS) has created an interest in determining the mechanical properties of these materials. In this work, FLCs for a TRIP steel were determined using Nakajima and Marciniak tests, which revealed different strain paths depending on the type of test. Determination of the FLCs was carried out following the mathematical calculations indicated in the ISO 12004 standard and was also compared with an alternative mathematical method, which showed different FLCs. Finally, the tests were verified by comparing the strain paths of the Nakajima and Marciniak tests with a well-known mild steel.

Evaluation of non-linear strain paths using Generalized Forming Limit Concept and a modification of the Time Dependent Evaluation Method

2016 ◽  
Vol 10 (3) ◽  
pp. 345-351 ◽  
Author(s):  
Christian Gaber ◽  
David Jocham ◽  
Hannes Alois Weiss ◽  
Ole Böttcher ◽  
Wolfram Volk
Keyword(s):  
Evaluation Method ◽  
Time Dependent ◽  
Forming Limit ◽  
Linear Strain ◽  
Limit Concept ◽  
Non Linear ◽  
Strain Paths

Finite Element Modeling of Deformation Behavior of Steel Specimens under Various Loading Scenarios

2015 ◽  
Vol 651-653 ◽  
pp. 969-974 ◽  
Author(s):  
Dilip Banerjee ◽  
Mark Iadicola ◽  
Adam Creuziger ◽  
Tim Foecke
Keyword(s):  
Finite Element ◽  
Deformation Behavior ◽  
Stress Measurement ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Fe Model ◽  
Strain Paths

Lightweighting materials (e.g., advanced high strength steels, aluminum alloys etc.) are increasingly being used by automotive companies as sheet metal components. However, accurate material models are needed for wider adoption. These constitutive material data are often developed by applying biaxial strain paths with cross-shaped (cruciform) specimens. Optimizing the design of specimens is a major goal in which finite element (FE) analysis can play a major role. However, verification of FE models is necessary. Calibrating models against uniaxial tensile tests is a logical first step. In the present study, reliable stress-strain data up to failure are developed by using digital image correlation (DIC) technique for strain measurement and X-ray techniques and/or force data for stress measurement. Such data are used to model the deformation behavior in uniaxial and biaxial tensile specimens. Model predictions of strains and displacements are compared with experimental data. The role of imperfections on necking behavior in FE modeling results of uniaxial tests is discussed. Computed results of deformation, strain profile, and von Mises plastic strain agree with measured values along critical paths in the cruciform specimens. Such a calibrated FE model can be used to obtain an optimum cruciform specimen design.

Sign in / Sign up

Export Citation Format

Share Document