Influence of two-step ball-milling condition on electrical and mechanical properties of TiC-dispersion-strengthened Cu alloys

2014 ◽  
Vol 64 ◽  
pp. 441-449 ◽  
Author(s):  
Fenglin Wang ◽  
Yunping Li ◽  
Kenta Yamanaka ◽  
Kimio Wakon ◽  
Koichi Harata ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Ball Milling ◽  
Cu Alloys ◽  
Milling Condition

Mechanical Properties of Nanocrystalline Materials Produced by In Situ Consolidation Ball Milling

2008 ◽  
Vol 579 ◽  
pp. 15-28 ◽  
Author(s):  
Carl C. Koch ◽  
Khaled M. Youssef ◽  
Ron O. Scattergood
Keyword(s):  
Mechanical Properties ◽  
Ball Milling ◽  
Nanocrystalline Materials ◽  
Preparation Method ◽  
High Strength ◽  
Al Alloys ◽  
Ductile Metals ◽  
Cu Alloys ◽  
Bulk Nanocrystalline

This paper reviews a method, “in situ consolidation ball milling” that provides artifactfree bulk nanocrystalline samples for several ductile metals such as Zn, Al and Al alloys, and Cu and Cu alloys. The preparation method is described in this paper and examples of the mechanical behavior of nanocrystalline materials made by this technique are given. It is found that in such artifact-free metals, combinations of both high strength and good ductility are possible.

Experimental Investigation and Micro-Structural Evolution Analysis of CNT & Fly Ash Reinforced Aluminium Matrix Composites

2015 ◽  
Vol 830-831 ◽  
pp. 429-432 ◽  
Author(s):  
Udaya ◽  
Peter Fernandes
Keyword(s):  
Mechanical Properties ◽  
Experimental Investigation ◽  
Fly Ash ◽  
Ball Milling ◽  
Milling Time ◽  
Structural Evolution ◽  
Matrix Composites ◽  
Evolution Analysis ◽  
Ball Milling Time ◽  
Al Matrix

The paper illustrates Carbon nanotubes reinforced pure Al (CNT/Al) composites and fly ash reinforced pure Al (FA/Al) composites produced by ball-milling and sintering. Microstructures of the fabricated composite were examined and the mechanical properties of the composites were tested and analysed. It was indicated that the CNTs and fly ash were uniformly dispersed into the Al matrix as ball-milling time increased with increase in hardness.

scholarly journals Mechanical Properties and Microstructures of Dental Cast Ti-Ag and Ti-Cu Alloys.

2002 ◽  
Vol 21 (3) ◽  
pp. 270-280 ◽  
Author(s):  
Masatoshi TAKAHASHI ◽  
Masafumi KIKUCHI ◽  
Yukyo TAKADA ◽  
Osamu OKUNO
Keyword(s):  
Mechanical Properties ◽  
Cu Alloys ◽  
Dental Cast

Effect of Zn on microstructure, texture and mechanical properties of Al-Mg-Si-Cu alloys with a medium number of Fe-rich phase particles

2017 ◽  
Vol 134 ◽  
pp. 123-133 ◽  
Author(s):  
Xiaofeng Wang ◽  
Mingxing Guo ◽  
Jinru Luo ◽  
Jie Zhu ◽  
Jishan Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Rich Phase ◽  
Cu Alloys
Sign in / Sign up

Export Citation Format

Share Document