A numerical study of heat transfer enhancement by helically corrugated tubes in the intermediate heat exchanger of a very-high-temperature gas-cooled reactor

2021 ◽  
Vol 380 ◽  
pp. 111275
Author(s):  
Qingxiang Hu ◽  
Kun Yuan ◽  
Wei Peng ◽  
Gang Zhao ◽  
Jie Wang
Author(s):  
Nariaki Sakaba ◽  
Shimpei Hamamoto ◽  
Yoichi Takeda

Lifetime extension of high-temperature equipment such as the intermediate heat exchanger of high-temperature gas-cooled reactors (HTGRs) is important from the economical point of view. Since the replacing cost will cause the increasing of the running cost, it is important to reduce replacing times of the high-cost primary equipment during assumed reactor lifetime. In the past, helium chemistry has been controlled by the passive chemistry control technology in which chemical impurity in the coolant helium is removed as low concentration as possible, as does Japan’s HTTR. Although the lifetime of high-temperature equipment almost depends upon the chemistry conditions in the coolant helium, it is necessary to establish an active chemistry control technology to maintain adequate chemical conditions. In this study, carbon deposition which could occur at the surface of the heat transfer tubes of the intermediate heat exchanger and decarburization of the high-temperature material of Hastelloy XR used at the heat transfer tubes were evaluated by referring the actual chemistry data obtained by the HTTR. The chemical equilibrium study contributed to clarify the algorism of the chemistry behaviours to be controlled. The created algorism is planned to be added to the instrumentation system of the helium purification systems. In addition, the chemical composition to be maintained during the reactor operation was proposed by evaluating not only core graphite oxidation but also carbon deposition and decarburization. It was identified when the chemical composition could not keep adequately, injection of 10 ppm carbon monoxide could effectively control the chemical composition to the designated stable area where the high-temperature materials could keep their structural integrity beyond the assumed duration. The proposed active chemistry control technology is expected to contribute economically to the purification systems of the future very high-temperature reactors.


Author(s):  
Shubham Agarwal ◽  
R. P. Sharma

This is a novel study for assessing the heat transfer enhancement in a multi-row inline-tube heat exchanger using hybrid vortex generator (VG) arrays, i.e., rectangular winglet pairs (RWPs) with different geometrical configurations installed in coherence for enhanced heat transfer. The three-dimensional numerical study uses a full scale seven-tube inline heat exchanger model. The effect of roll of rectangular winglet VG on heat transfer enhancement is analyzed and optimized roll angle is determined for maximum heat transfer enhancement. Four different configurations are analyzed and compared in this regard: (a) single RWP (no roll); (b) 3RWP-inline array(alternating tube row with no roll of VGs); (c) single RWP (with optimized roll angle VGs); and (d) 3RWP-inline array(alternating tube row with all VGs having optimized roll angle). It was found that the inward roll of VGs increased the heat transfer from the immediately downstream tube but reduced heat transfer enhancement capability of other VG pairs downstream. Further, four different hybrid configurations of VGs were analyzed and the optimum configuration was obtained. For the optimized hybrid configuration at Re = 670, RWP with optimized roll angle increased heat transfer by 17.5% from the tube it was installed on and by 42% from the immediately downstream tube. Increase in j/ƒ of 36.7% is obtained by use of hybrid VGs in the optimized hybrid configuration. The deductions from the current study are supposed to well enhance the performance of heat exchangers with different design configurations.


2006 ◽  
Vol 129 (9) ◽  
pp. 1156-1167 ◽  
Author(s):  
A. Joardar ◽  
A. M. Jacobi

This work is aimed at assessing the potential of winglet-type vortex generator (VG) “arrays” for multirow inline-tube heat exchangers with an emphasis on providing fundamental understanding of the relation between local flow behavior and heat transfer enhancement mechanisms. Three different winglet configurations in common-flow-up arrangement are analyzed in the seven-row compact fin-and-tube heat exchanger: (a) single–VG pair; (b) a 3VG-inline array (alternating tube row); and (c) a 3VG-staggered array. The numerical study involves three-dimensional time-dependent modeling of unsteady laminar flow (330⩽Re⩽850) and conjugate heat transfer in the computational domain, which is set up to model the entire fin length in the air flow direction. It was found that the impingement of winglet redirected flow on the downstream tube is an important heat transfer augmentation mechanism for the common-flow-up arrangement of vortex generators in the inline-tube geometry. At Re=850 with a constant tube-wall temperature, the 3VG-inline-array configuration achieves enhancements up to 32% in total heat flux and 74% in j factor over the baseline case, with an associated pressure-drop increase of about 41%. The numerical results for the integral heat transfer quantities agree well with the available experimental measurements.


2008 ◽  
Vol 595-598 ◽  
pp. 501-509
Author(s):  
Damien Kaczorowski ◽  
Gouenou Girardin ◽  
S. Chamousset

Nickel base alloys 617 and 230 are promising candidates for the Intermediate Heat eXchanger (IHX) of GenIV Very High Temperature gas cooled Reactors. The capability to maintain an oxide layer as an efficient barrier against corrosion under mechanical loading is investigated through SEM in situ tensile test. The mechanical properties of external oxide layers are so compared between the two alloys. Cracks and spallation are observed. Few differences could be observed between these two alloys when pre oxidized in impure helium.


Sign in / Sign up

Export Citation Format

Share Document