Active Chemistry Control for Coolant Helium Applying High-Temperature Gas-Cooled Reactors

Author(s):  
Nariaki Sakaba ◽  
Shimpei Hamamoto ◽  
Yoichi Takeda

Lifetime extension of high-temperature equipment such as the intermediate heat exchanger of high-temperature gas-cooled reactors (HTGRs) is important from the economical point of view. Since the replacing cost will cause the increasing of the running cost, it is important to reduce replacing times of the high-cost primary equipment during assumed reactor lifetime. In the past, helium chemistry has been controlled by the passive chemistry control technology in which chemical impurity in the coolant helium is removed as low concentration as possible, as does Japan’s HTTR. Although the lifetime of high-temperature equipment almost depends upon the chemistry conditions in the coolant helium, it is necessary to establish an active chemistry control technology to maintain adequate chemical conditions. In this study, carbon deposition which could occur at the surface of the heat transfer tubes of the intermediate heat exchanger and decarburization of the high-temperature material of Hastelloy XR used at the heat transfer tubes were evaluated by referring the actual chemistry data obtained by the HTTR. The chemical equilibrium study contributed to clarify the algorism of the chemistry behaviours to be controlled. The created algorism is planned to be added to the instrumentation system of the helium purification systems. In addition, the chemical composition to be maintained during the reactor operation was proposed by evaluating not only core graphite oxidation but also carbon deposition and decarburization. It was identified when the chemical composition could not keep adequately, injection of 10 ppm carbon monoxide could effectively control the chemical composition to the designated stable area where the high-temperature materials could keep their structural integrity beyond the assumed duration. The proposed active chemistry control technology is expected to contribute economically to the purification systems of the future very high-temperature reactors.

2010 ◽  
Vol 9 (2) ◽  
pp. 219-232 ◽  
Author(s):  
Yorikata MIZOKAMI ◽  
Toshihide IGARI ◽  
Keiichi NAKASHIMA ◽  
Fumiko KAWASHIMA ◽  
Noriyuki SAKAKIBARA ◽  
...  

2008 ◽  
Vol 595-598 ◽  
pp. 501-509
Author(s):  
Damien Kaczorowski ◽  
Gouenou Girardin ◽  
S. Chamousset

Nickel base alloys 617 and 230 are promising candidates for the Intermediate Heat eXchanger (IHX) of GenIV Very High Temperature gas cooled Reactors. The capability to maintain an oxide layer as an efficient barrier against corrosion under mechanical loading is investigated through SEM in situ tensile test. The mechanical properties of external oxide layers are so compared between the two alloys. Cracks and spallation are observed. Few differences could be observed between these two alloys when pre oxidized in impure helium.


Author(s):  
Yannan Wu ◽  
Yujie Dong ◽  
Kun Yuan

In order to improve the thermal efficiency of the intermediate heat exchanger (IHX) in high temperature gas-cooled reactor, the article takes a theoretical calculation and simulation analysis of different turbulence models on the turbulent flow boundary layer of the IHX. And a suitable model for the high temperature and high pressure unit of the IHX is built. According to the boundary layer distribution of different models and the fluid velocity and temperature changes of central region, we find the related characteristics and cut-off point of the boundary layer area and the Poiseuille flow area. At the same time, the paper verifies the three kinds of turbulence model and the formula with solution theory, including the relationship of Nu (Nusselt) number and Re (Reynolds) number and the partial wall friction resistance. These results provides theoretical support for the next step of the heat transfer enhancement research using the artificial roughness elements.


2016 ◽  
Vol 713 ◽  
pp. 280-283 ◽  
Author(s):  
Kee Nam Song ◽  
Eung Seon Kim ◽  
S.Y. Jang

The IHX (Intermediate Heat Exchanger) of a VHTR (Very High Temperature Reactor) transfers 950°C heat generated from the VHTR to a hydrogen production plant. The Korea Atomic Energy Research Institute has manufactured a lab-scale Alloy 800HT PCHE (Printed Circuit Heat Exchanger) prototype under consideration as a candidate of the IHX (Intermediate Heat Exchanger). In this study, as a part of a structural integrity evaluation of the PCHE prototype, an elasto-plastic structural analysis including a thermal analysis was carried out under the designed test conditions of the PCHE prototype in a helium experimental loop (HELP). The analysis results were reflected to re-design the pipeline layout of HELP and to determine the actual test conditions of the PCHE prototype in the re-designed HELP in view of experimental safety.


Sign in / Sign up

Export Citation Format

Share Document