Generic Wavelength-routed Optical Router (GWOR) based on grating-assisted vertical couplers for multilayer optical networks

Insertion loss and crosstalk noise will influence network performance severely, especially in optical networks-on-chip (ONoCs) when wavelength division multiplexing (WDM) technology is employed. In this paper, an insertion loss and crosstalk analysis model for WDM-based torus ONoCs is proposed to evaluate the network performance. To demonstrate the feasibility of the proposed methods, numerical simulations of the WDM-based torus ONoCs with optimized crossbar and crux optical routers are presented, and the worst-case link and network scalability are also revealed. The numerical simulation results demonstrate that the scale of the WDM-based torus ONoCs with the crux optical router can reach 6 × 5 or 5 × 6 before the noise power exceeds the signal power, and the network scale is 5 × 4 in the worst case when the optimized crossbar router is employed. Additionally, the simulated results of OptiSystem reveal that WDM-based torus ONoCs have better signal transmission quality when using the crux optical router, which is consistent with previous numerical simulations. Furthermore, compared with the single-wavelength network, WDM-based ONoCs have a great performance improvement in end-to-end (ETE) delay and throughput according to the simulated results of OPNET. The proposed network analysis method provides a reliable theoretical basis and technical support for the design and performance optimization of ONoCs.

Download Full-text

A Promise for Software-defined Optical Networks: Optical Router Engine Design enabled by Cloud-based Spatio-Temporal Label Computing and Switching Protocol (Invited)1

Advanced Photonics 2013 ◽

10.1364/networks.2013.nt2c.2 ◽

2013 ◽

Author(s):

Anpeng Huang ◽

Linzhen Xie ◽

Anshi Xu ◽

Zhangyuan Chen

Keyword(s):

Optical Networks ◽

Optical Router ◽

Engine Design ◽

Spatio Temporal

Download Full-text

A Novel Algorithm for Routing Paths Selection in Mesh-Based Optical Networks-on-Chips

Micromachines ◽

10.3390/mi11110996 ◽

2020 ◽

Vol 11 (11) ◽

pp. 996

Author(s):

Xiao-Ping Yang ◽

Ting-Ting Song ◽

Yi-Chen Ye ◽

Bo-Cheng Liu ◽

Hua Yan ◽

...

Keyword(s):

Optical Networks ◽

Power Loss ◽

Signal To Noise Ratio ◽

Optical Network ◽

Routing Algorithm ◽

Optical Signal ◽

Crosstalk Noise ◽

Optical Router ◽

Networks On Chips ◽

Novel Algorithm

Optical networks-on-chips (ONoCs) is an effective and extensible on-chip communication technology, which has the characteristics of high bandwidth, low consumption, and low delay. In the design process of ONoCs, power loss is an important factor for limiting the scalability of ONoCs. Additionally, the optical signal-to-noise ratio (OSNR) is an index to measure the quality of ONoCs. Nowadays, the routing algorithm commonly used in ONoCs is the dimension-order routing algorithm, but the routing paths selected by the algorithm have high power loss and crosstalk noise. In this paper, we propose a 5×5 all-pass optical router model for two-dimensional (2-D) mesh-based ONoCs. Based on the general optical router model and the calculation models of power loss and crosstalk noise, a novel algorithm is proposed in ordder to select the routing paths with the minimum power loss. At the same time, it can ensure that the routing paths have the approximately optimal OSNR. Finally, we employ the Cygnus optical router to verify the proposed routing algorithm. The results show that the algorithm can effectively reduce the power loss and improve the OSNR in the case of network sizes of 5×5 and 6×6. With the increase of the optical network scale, the algorithm can perform better in reducing the power loss and raising the OSNR.

Download Full-text