Electrical discharge machining of the AISI D6 tool steel: Prediction and modeling of the material removal rate and tool wear ratio

2016 ◽  
Vol 45 ◽  
pp. 435-444 ◽  
Author(s):  
Reza Vatankhah Barenji ◽  
Hamed H. Pourasl ◽  
Vahid M. Khojastehnezhad
Keyword(s):  
Tool Wear ◽  
Tool Steel ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Wear Ratio ◽  
Tool Wear Ratio

Material Removal Rate and Tool Wear Ratio for Powder Mixed Dielectric Based Electric Discharge Machining

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Gurmail Singh Malhi ◽  
Gurpreet Singh Sokhal ◽  
Gurprinder Singh Dhindsa ◽  
Kamaljit Singh Sokhal
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Performance Study ◽  
Tool Wear Rate ◽  
Electric Discharge Machining ◽  
Tool Wear Ratio

Electrical discharge machining (EDM) is used in die making and aerospace industries. This paper presents the performance study of the conventional EDM when used with powder mixed dielectric. Copper, graphite and mix (copper and graphite) were used. Pulse on, pulse off and current are the parameters which were varied at three levels. Copper, graphite and tungsten-copper were used as the electrode. The material removal rate and tool wear rate are assessed using design of experiments.

CHARACTERIZATION OF ZrB2-SiC COMPOSITES WITH AN ANALYTICAL STUDY ON MATERIAL REMOVAL RATE AND TOOL WEAR RATE DURING ELECTRICAL DISCHARGE MACHINING

2016 ◽  
Vol 40 (3) ◽  
pp. 331-349 ◽  
Author(s):  
S. Sivasankar ◽  
R. Jeyapaul
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Relative Density ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Tool Materials

This research work concentrates on Electrical Discharge Machining (EDM) performance evaluation of ZrB2- SiC ceramic matrix composites with different tool materials at various machining parameters. Monolithic ZrB2 possesses lower relative density (98.72%) than composites. ZrB2 with 20 Vol.% of SiC possesses 99.74% of the relative density with improved hardness values. Bend strength and Young’s modulus increase with SiC addition until it reaches 20 Vol% and then decreasing. EDM performance on tool materials of tungsten, niobium, tantalum, graphite and titanium at various levels of pulse on time and pulse off time are analyzed. Graphite produces the best Material removal rate (MRR) for all the workpieces. Tool wear rate decreases with melting point and thermal conductivity of the tool material.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Analysis of MRR and TWR on OHNS Die Steel with Different Electrodes Using Electrical Discharge Machining

2016 ◽  
Vol 22 ◽  
pp. 112-120 ◽  
Author(s):  
S. Nallusamy
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Dielectric Fluid ◽  
Work Piece ◽  
Tool Wear Rate

Electrical Discharge Machining is a machining method primarily used for hard metals or those that are impossible to be machined with traditional techniques. The experimental investigation of material removal rate and tool wear rate during machining of oil hardened non-shrinking steel with brass and copper electrodes using EDM machine was carried out in this paper. This investigation presents the analysis and evaluation of heat affected zones and surface finish of the work piece using different tool electrodes and varying the machine parameters. The commercial grade kerosene oil has been used as dielectric fluid. The effect of various important EDM parameters such as discharge current (Ip) 2 to12A, pulse duration (Ton and Toff) and sparking voltage (V) of 80±5% have been used to yield the response in terms of Material Removal Rate (MRR) and Tool Wear Rate (TWR). Further a detailed analysis of the heat affected regions was also been carried out by using scanning electron microscopy.

PENGARUH PARAMETER PROSES EDM DIE SINKING TERHADAP LAJU PELEPASAN BAHAN DAN LAJU KEAUSAN ELEKTRODA

2019 ◽  
Vol 1 (2) ◽  
pp. 105-112
Author(s):  
Nafsan Upara ◽  
Dimas Anugrah Destianto
Keyword(s):  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Orthogonal Array ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate

Electrical Discharge Machining (EDM) merupakan pemesinan nonkonvensional yang memanfaatkan proses konversi listrik dan panas, dimana energi listrik digunakan untuk memunculkan loncatan bunga api dan proses pelepassan bahan terjadi akibat energi panas yang ditimbulkan dari bunga api tersebut.Keausan elektroda pada proses EDM die sinking merupakan peristiwa yang tidak dapat di hindari, namun dengan mengatur parameter pemotongan yang sesuai, diharapkan keausan yang terjadi pada elektroda se-minim mungkin dan pemakanan benda kerja semaksimal mungkin sehingga didapati tingkat akurasi ukuran pada benda kerja. Pada penelitian ini menggunakan metode Taguchi  dengan L8 orthogonal array memakai elektroda bahan tembaga dan benda kerja material SKS 3. S/N ratio dan ANOVA menentukan performa parameter proses EDM dengan respon yang di teliti adalah Material Removal Rate (MRR) dan Tool Wear Rate (TWR). Hasil dari eksperimen tersebut menghasilkan parameter optimum Aruslevel 2= 6 A; Ponlevel 1=100 µs dan Pofflevel 1=50µs.

Machinability Evaluation by Single Electrical Discharge

2013 ◽  
Vol 371 ◽  
pp. 290-294 ◽  
Author(s):  
Lorelei Gherman ◽  
Ionut Palaghia ◽  
Laurenţiu Slătineanu
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Copper Alloys ◽  
Tool Electrode ◽  
Thin Sheets ◽  
Process Factors

Electrical discharge machining is widely used in processing complex shaped parts. The method uses a tool electrode having a specific geometry, but the tool wear can affect such geometry in time. An affordable material for obtaining tool electrodes with complicated profiles can be electrolytic copper. Some issues appear when workpiece materials made also out of copper or copper alloys are processed, as the copper tool life span decreases. Machinability is the property of a material that indicates good process outcomes for the manufacturer, such as a high material removal rate and low tool wear. In order to determine some machinability indicators such as tool wear and material removal rate, a set of experiments were designed for single discharge machining using thin sheets of copper as tool electrodes and thin sheets of brass as test pieces, with workpiece thicknesses of 0.1 mm. The craters obtained after discharge were analyzed by means of a digital microscope. Based on these results, a statistical analysis was developed and the influence of input process factors was evaluated.

Sign in / Sign up

Export Citation Format

Share Document