Friction and wear of liner and grinding ball in iron ore ball mill

2017 ◽  
Vol 115 ◽  
pp. 506-517 ◽  
Author(s):  
Yu-xing Peng ◽  
Xu Ni ◽  
Zhen-cai Zhu ◽  
Zhang-fa Yu ◽  
Zi-xin Yin ◽  
...  
Keyword(s):  
Ball Mill ◽  
Friction And Wear ◽  
Iron Ore

Tribological Behavior of Mesophase Carbon Added with Titanium and Copper

2011 ◽  
Vol 80-81 ◽  
pp. 60-63
Author(s):  
Xue Qing Yue ◽  
Hua Wang ◽  
Shu Ying Wang
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Friction Coefficient ◽  
Ball Mill ◽  
Friction And Wear ◽  
Applied Load ◽  
Tribological Behavior ◽  
Metallic Elements ◽  
X Ray Diffraction ◽  
X Ray

Incorporation of metallic elements, titanium and copper, into carbonaceous mesophase (CM) was performed through mechanical alloying in a ball mill apparatus. The structures of the raw CM as well as the Ti/Cu-added CM were characterized by X-ray diffraction. The tribological behavior of the Ti/Cu-added CM used as lubricating additives was investigated by using a high temperature friction and wear tester. The results show that, compared with the raw CM, the Ti/Cu-added CM exhibits a drop in the crystallinity and a transition to the amorphous. The Ti/Cu-added CM used as lubricating additive displays an obvious high temperature anti-friction and wear resistance effect, and the lager the applied load, the lower the friction coefficient and the wear severity.

Failure analysis of a steel slide ring of a tubular ball mill used in an iron ore mining plant

2020 ◽  
Vol 110 ◽  
pp. 104433
Author(s):  
Leonardo Barbosa Godefroid ◽  
Luiz Cláudio Cândido ◽  
Claudinei Roberto Guimarães ◽  
Sidney Cardoso Araújo
Keyword(s):  
Failure Analysis ◽  
Ball Mill ◽  
Iron Ore ◽  
Mining Plant

Tribological Performance of Iron Ore Tailings Enhanced Resin Composites for Automotive Brake Linings

2011 ◽  
Vol 189-193 ◽  
pp. 4387-4390
Author(s):  
Gui Hua Hou ◽  
Zhan Hong Wang
Keyword(s):  
Composite Materials ◽  
Friction And Wear ◽  
Iron Ore ◽  
Resin Composites ◽  
Wear Properties ◽  
Molding Method ◽  
Iron Ore Tailings ◽  
Friction And Wear Properties ◽  
Automotive Clutch ◽  
Automotive Brake

Iron tailings is the bulk waste produced by steel plants that has not yet been used. In this study, the mineral composition of iron tailings was determined by XRD. The microstructure was observed by SEM-BEI. Resin-based composite materials with different contents of iron tailings were prepared by compression molding method and the tribological properties of the composites were studied. The results showed that: when the contents of iron tailings were 10%, 20%, 30%, 40% and 50%, the friction and wear properties of the resin-based composite materials can meet the standards for automotive clutch (GB/T 5764-1998). Among these samples, the sample with 20% iron tailings had the best performance. This paper provides a new way for the use of iron tailings.

scholarly journals Study on heat transfer behavior and thermal breakage characteristic of the charge in ball mills

2021 ◽  
Vol 13 (3) ◽  
pp. 168781402199496
Author(s):  
Tongqing Li ◽  
Zixin Yin ◽  
Guiyi Wu
Keyword(s):  
Heat Transfer ◽  
Ball Mill ◽  
Iron Ore ◽  
Heating Temperature ◽  
Temperature Fields ◽  
Ball Mills ◽  
Optimal Feed ◽  
Underlying Mechanisms ◽  
Mill Speed ◽  
Charge Temperature

Ball mill is the widely used comminution device for the size reduction of iron ore particles, yet the underlying mechanisms of heat transfer and thermal breakage inside the mills heretofore are not deeply understood. Therefore, the Discrete element method was carried out to study the effect of operating parameters on charge temperature, and the batch grinding experiments of iron ores were conducted to verify the heating temperatures using a laboratory ball mill. Results show that increasing mill speed will result in the charge temperature increasing initially and then decreasing. The temperature fields of the charge and load behavior remain approximately the same for the different ball filling. The main findings of this study are that the heating temperature can contribute to enhancing the breakage behavior of iron ore particles, and correspondingly the optimal feed sizes for different heating temperatures are determined to be 2.48 mm, 2.63 mm, 2.78 mm, and 3.59 mm, respectively.

scholarly journals Discrete element method simulations of load behavior with mono-sized iron ore particles in a ball mill

2017 ◽  
Vol 9 (5) ◽  
pp. 168781401770559 ◽  
Author(s):  
Yuxing Peng ◽  
Tongqing Li ◽  
Zhencai Zhu ◽  
Shengyong Zou ◽  
Zixin Yin
Keyword(s):  
Discrete Element Method ◽  
Ball Mill ◽  
Iron Ore ◽  
Discrete Element ◽  
Load Behavior ◽  
Element Method

EVALUATION OF THE MECHANICAL BEHAVIOR OF STEELS USED IN THE SLIDE RING OF A BALL MILL OF AN IRON ORE MINING PLANT

2019 ◽  
Author(s):  
Claudinei Roberto Guimarães ◽  
Leonardo Godefroid ◽  
Luiz Cláudio Cândido ◽  
Sidney Araújo
Keyword(s):  
Mechanical Behavior ◽  
Ball Mill ◽  
Iron Ore ◽  
Mining Plant

The Study of the Properties and Function of Large Ball Mill with Liner Material

2011 ◽  
Vol 117-119 ◽  
pp. 1044-1047
Author(s):  
Jing Pei Xie ◽  
Ning Bo Li ◽  
Wen Yan Wang ◽  
Ai Qin Wang ◽  
Pei Zhang
Keyword(s):  
Ball Mill ◽  
High Speed ◽  
Friction And Wear ◽  
Large Scale ◽  
Testing Machine ◽  
Reduction Rate ◽  
Extension Rate ◽  
Tempering Temperature ◽  
Liner Material ◽  
Scanning Electron Microscope Study

In this paper, based on ctual large-scale ball mill liners working conditions, effects of different quenching temperature and tempering temperature on the Cr-Mo steel performance, optimize the best heat treatment process.The use of sophisticated electronic universal tensile testing machine, and Rockwell hardness testing machine for testing mechanical properties of steel materials were tested; Using the MMS-1G-type high-temperature high-speed Friction and wear tester, the wear properties of steel samples were studied using JSM-5610LV scanning electron microscope study of the tensile test fracture surfaces of steel and the friction and wear morphology. The results show that: For the high carbon alloy steel, of which 870 °C 620 °C tempered quenched specimen extension rate of 7.0% area reduction rate of 9.5%.

Xperimental Research on Grinding Medium and Influence Factors of SiJiaYing's Fine Grain Hematite

2013 ◽  
Vol 641-642 ◽  
pp. 557-561
Author(s):  
Bing Liang ◽  
Li Bing Zhao ◽  
Jin Rui Zhang
Keyword(s):  
Ball Mill ◽  
Iron Ore ◽  
Influence Factors ◽  
Filling Ratio ◽  
Gangue Mineral ◽  
Grinding Process ◽  
Sphere Diameter ◽  
Effect Factor ◽  
Fine Grain

SiJiaYing's iron ore is fine grain hematite and gangue mineral is quartz,chlorite,black mica and parts of clay mineral.Grinding process is tend to argillation,which seriously impact the subsequent strong magnetic and flotation thick operation.This paper mainly conduct ball mill sphere diameter,ball ratio and the grinding effect factor test,which including medium filling ratio,grinding concentration and so on.By compared experiments optimize,grinding process and improve the grinding effect.

scholarly journals POPULATION BALANCE MODEL APPROACH TO BALL MILL OPTIMIZATION IN IRON ORE GRINDING

2014 ◽  
Author(s):  
Patrícia Mundim Campos Faria ◽  
Luís Marcelo Tavares ◽  
Raj K. Rajamani
Keyword(s):  
Ball Mill ◽  
Iron Ore ◽  
Population Balance ◽  
Balance Model ◽  
Population Balance Model ◽  
Model Approach
Sign in / Sign up

Export Citation Format

Share Document