Determination of the Values of the Technological Parameters which are Used to Describe the Time Course of Cutting Force Components in Milling

CIRP Annals ◽  
1985 ◽  
Vol 34 (1) ◽  
pp. 141-144 ◽  
Author(s):  
K.-D. Bouzakis ◽  
G. Methenitis ◽  
W. König
Keyword(s):  
Cutting Force ◽  
Time Course ◽  
Technological Parameters ◽  
Cutting Force Components ◽  
Force Components

scholarly journals Determination of specific cutting force components and exponents when applying high feed rates

Procedia CIRP ◽  
2018 ◽  
Vol 77 ◽  
pp. 30-33 ◽  
Author(s):  
Bernhard Karpuschewski ◽  
János Kundrák ◽  
Gyula Varga ◽  
István Deszpoth ◽  
Dmytro Borysenko
Keyword(s):  
Cutting Force ◽  
Specific Cutting Force ◽  
High Feed ◽  
Cutting Force Components ◽  
Force Components

Determination of Cutting Forces in Oblique Cutting

2015 ◽  
Vol 756 ◽  
pp. 659-664 ◽  
Author(s):  
A.V. Filippov ◽  
E.O. Filippova
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
Theoretical Calculations ◽  
Experimental Investigations ◽  
Cutting Depth ◽  
Turning Operations ◽  
Error Check ◽  
Cutting Force Components ◽  
Force Components

This study describes the method of determining cutting force components in oblique turning. The scheme of how the investigations were performed is presented. The characteristic curves of cutting force components vs. thickness of the material removed, tool clearance and tool rake angles are shown. The study presents the data, which have been obtained during the experimental investigations and analytically calculated, on how the cutting forces are subject to changes depending on a cutter angle, cutting depth and feed in oblique turning operations. The analysis of approximation of the experimental results and error check of the theoretical calculations relative to the experimental data are given.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

Artificial neural networks back propagation algorithm for cutting force components predictions

2013 ◽  
Vol 14 (6) ◽  
pp. 431-439 ◽  
Author(s):  
Issam Hanafi ◽  
Francisco Mata Cabrera ◽  
Abdellatif Khamlichi ◽  
Ignacio Garrido ◽  
José Tejero Manzanares
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Cutting Force ◽  
Back Propagation ◽  
Back Propagation Algorithm ◽  
Propagation Algorithm ◽  
Cutting Force Components ◽  
Artificial Neural ◽  
Force Components
Sign in / Sign up

Export Citation Format

Share Document