Leading-edge receptivity to free-stream disturbance waves for hypersonic flow over a parabola

2001 ◽  
Vol 441 ◽  
pp. 315-367 ◽  
Author(s):  
XIAOLIN ZHONG
Keyword(s):  
Boundary Layer ◽  
Hypersonic Flow ◽  
Boundary Layers ◽  
Free Stream ◽  
Stokes Equations ◽  
Leading Edge ◽  
Bow Shock ◽  
Navier Stokes ◽  
Hypersonic Boundary Layer ◽  
Disturbance Waves

The receptivity of hypersonic boundary layers to free-stream disturbances, which is the process of environmental disturbances initially entering the boundary layers and generating disturbance waves, is altered considerably by the presence of bow shocks in hypersonic flow fields. This paper presents a numerical simulation study of the generation of boundary layer disturbance waves due to free-stream waves, for a two-dimensional Mach 15 viscous flow over a parabola. Both steady and unsteady flow solutions of the receptivity problem are obtained by computing the full Navier–Stokes equations using a high-order-accurate shock-fitting finite difference scheme. The effects of bow-shock/free-stream-sound interactions on the receptivity process are accurately taken into account by treating the shock as a discontinuity surface, governed by the Rankine-Hugoniot relations. The results show that the disturbance waves generated and developed in the hypersonic boundary layer contain both first-, second-, and third-mode waves. A parametric study is carried out on the receptivity characteristics for different free-stream waves, frequencies, nose bluntness characterized by Strouhal numbers, Reynolds numbers, Mach numbers, and wall cooling. In this paper, the hypersonic boundary-layer receptivity is characterized by a receptivity parameter defined as the ratio of the maximum induced wave amplitude in the first-mode-dominated region to the amplitude of the free-stream forcing wave. It is found that the receptivity parameter decreases when the forcing frequency or nose bluntness increase. The results also show that the generation of boundary layer waves is mainly due to the interaction of the boundary layer with the acoustic wave field behind the bow shock, rather than interactions with the entropy and vorticity wave fields.

scholarly journals Free-stream coherent structures in the unsteady Rayleigh boundary layer

2020 ◽  
Vol 85 (6) ◽  
pp. 1021-1040
Author(s):  
Eleanor C Johnstone ◽  
Philip Hall
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Coherent Structures ◽  
Free Stream ◽  
Stokes Equations ◽  
Boundary Region ◽  
Navier Stokes ◽  
Equilibrium Solutions ◽  
Nonlinear Equilibrium ◽  
Set Up

Abstract Results are presented for nonlinear equilibrium solutions of the Navier–Stokes equations in the boundary layer set up by a flat plate started impulsively from rest. The solutions take the form of a wave–roll–streak interaction, which takes place in a layer located at the edge of the boundary layer. This extends previous results for similar nonlinear equilibrium solutions in steady 2D boundary layers. The results are derived asymptotically and then compared to numerical results obtained by marching the reduced boundary-region disturbance equations forward in time. It is concluded that the previously found canonical free-stream coherent structures in steady boundary layers can be embedded in unbounded, unsteady shear flows.

Swept-wing boundary-layer receptivity

2012 ◽  
Vol 700 ◽  
pp. 490-501 ◽  
Author(s):  
David Tempelmann ◽  
Ardeshir Hanifi ◽  
Dan S. Henningson
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Free Stream ◽  
Stokes Equations ◽  
Cross Flow ◽  
Leading Edge ◽  
Navier Stokes ◽  
Flow Mode ◽  
Swept Wing ◽  
Worst Case

AbstractAdjoint solutions of the linearized incompressible Navier–Stokes equations are presented for a cross-flow-dominated swept-wing boundary layer. For the first time these have been computed in the region upstream of the swept leading edge and may therefore be used to predict receptivity to any disturbances of the incoming free stream as well as to surface roughness. In this paper we present worst-case scenarios, i.e. those external disturbances yielding maximum receptivity amplitudes of a steady cross-flow disturbance. In the free stream, such an ‘optimal’ disturbance takes the form of a streak which, while being convected downstream, penetrates the boundary layer and smoothly turns into a growing cross-flow mode. The ‘worst-case’ surface roughness has a wavy shape and is distributed in the chordwise direction. It is shown that, under such optimal conditions, the boundary layer is more receptive to surface roughness than to incoming free stream disturbances.

Essential Ingredients for the Computation of Steady and Unsteady Blade Boundary Layers

1991 ◽  
Vol 113 (4) ◽  
pp. 608-616 ◽  
Author(s):  
H. M. Jang ◽  
J. A. Ekaterinaris ◽  
M. F. Platzer ◽  
T. Cebeci
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Stokes Equations ◽  
Inviscid Flow ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Transitional Region ◽  
Low Reynolds Numbers ◽  
Flow Equations ◽  
Low Reynolds

Two methods are described for calculating pressure distributions and boundary layers on blades subjected to low Reynolds numbers and ramp-type motion. The first is based on an interactive scheme in which the inviscid flow is computed by a panel method and the boundary layer flow by an inverse method that makes use of the Hilbert integral to couple the solutions of the inviscid and viscous flow equations. The second method is based on the solution of the compressible Navier–Stokes equations with an embedded grid technique that permits accurate calculation of boundary layer flows. Studies for the Eppler-387 and NACA-0012 airfoils indicate that both methods can be used to calculate the behavior of unsteady blade boundary layers at low Reynolds numbers provided that the location of transition is computed with the en method and the transitional region is modeled properly.

Free-stream coherent structures in parallel boundary-layer flows

2014 ◽  
Vol 752 ◽  
pp. 602-625 ◽  
Author(s):  
Kengo Deguchi ◽  
Philip Hall
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Coherent Structures ◽  
Free Stream ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Homotopy Continuation ◽  
Boundary Layer Flows ◽  
Navier Stokes Equations ◽  
High Reynolds

AbstractOur concern in this paper is with high-Reynolds-number nonlinear equilibrium solutions of the Navier–Stokes equations for boundary-layer flows. Here we consider the asymptotic suction boundary layer (ASBL) which we take as a prototype parallel boundary layer. Solutions of the equations of motion are obtained using a homotopy continuation from two known types of solutions for plane Couette flow. At high Reynolds numbers, it is shown that the first type of solution takes the form of a vortex–wave interaction (VWI) state, see Hall & Smith (J. Fluid Mech., vol. 227, 1991, pp. 641–666), and is located in the main part of the boundary layer. On the other hand, here the second type is found to support an equilibrium solution of the unit-Reynolds-number Navier–Stokes equations in a layer located a distance of $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}O(\ln \mathit{Re})$ from the wall. Here $\mathit{Re}$ is the Reynolds number based on the free-stream speed and the unperturbed boundary-layer thickness. The streaky field produced by the interaction grows exponentially below the layer and takes its maximum size within the unperturbed boundary layer. The results suggest the possibility of two distinct types of streaky coherent structures existing, possibly simultaneously, in disturbed boundary layers.

Similarity Solutions for the Interaction of a Potential Vortex With Free Stream Sink Flow and a Stationary Surface

1974 ◽  
Vol 96 (1) ◽  
pp. 49-54 ◽  
Author(s):  
J. A. Hoffmann
Keyword(s):  
Boundary Layer ◽  
Differential Equations ◽  
Free Stream ◽  
Stokes Equations ◽  
Similarity Solutions ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Stationary Surface ◽  
Direct Numerical Integration ◽  
Potential Vortex

Similarity equations, using an assumed transformation which reduces the partial differential equations to sets of ordinary differential equations, are obtained from the boundary layer and the complete Navier-Stokes equations for the interaction of vortex flows with free stream sink flows and a stationary surface. Solutions to the boundary layer equations for the case of the potential vortex that satisfy the prescribed boundary conditions are shown to be nonexistent using the assumed transformation. Direct numerical integration is used to obtain solutions to the complete Navier-Stokes equations under a potential vortex with equal values of tangential and radial free stream velocities. Solutions are found for Reynolds numbers up to 2.0.

Boundary layer development after a separated region

1998 ◽  
Vol 374 ◽  
pp. 91-116 ◽  
Author(s):  
IAN P. CASTRO ◽  
ELEANORA EPIK
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulence Models ◽  
Separated Flow ◽  
Leading Edge ◽  
Turbulence Structure ◽  
Outer Flow ◽  
Free Stream Turbulence ◽  
Layer Region

Measurements obtained in boundary layers developing downstream of the highly turbulent, separated flow generated at the leading edge of a blunt flat plate are presented. Two cases are considered: first, when there is only very low (wind tunnel) turbulence present in the free-stream flow and, second, when roughly isotropic, homogeneous turbulence is introduced. With conditions adjusted to ensure that the separated region was of the same length in both cases, the flow around reattachment was significantly different and subsequent differences in the development rate of the two boundary layers are identified. The paper complements, but is much more extensive than, the earlier presentation of some of the basic data (Castro & Epik 1996), confirming not only that the development process is very slow, but also that it is non-monotonic. Turbulence stress levels fall below those typical of zero-pressure-gradient boundary layers and, in many ways, the boundary layer has features similar to those found in standard boundary layers perturbed by free-stream turbulence. It is argued that, at least as far as the turbulence structure is concerned, the inner layer region develops no more quickly than does the outer flow and it is the latter which essentially determines the overall rate of development of the whole flow. Some numerical computations are used to assess the extent to which current turbulence models are adequate for such flows.

scholarly journals Essential Ingredients for the Computation of Steady and Unsteady Blade Boundary Layers

1990 ◽  
Author(s):  
H. M. Jang ◽  
M. F. Platzer ◽  
J. A. Ekaterinaris ◽  
T. Cebeci
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Stokes Equations ◽  
Inviscid Flow ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Transitional Region ◽  
Low Reynolds Numbers ◽  
Flow Equations ◽  
Low Reynolds

Two methods are described for calculating pressure distributions and boundary layers on blades subjected to low Reynolds numbers and ramp–type motion. The first is based on an interactive scheme in which the inviscid flow is computed by a panel method and the boundary layer flow by an inverse method that makes use of the Hilbert integral to couple the solutions of the inviscid and viscous flow equations. The second method is based on the solution of the compressible Navier–Stokes equations with an embedded grid technique that permits accurate calculation of boundary layer flows. Studies for the Eppler and NACA–0012 airfoils indicate that both methods can be used to calculate the behavior of unsteady blade boundary layers at low Reynolds numbers provided that the location of transition is computed with the en–method and the transitional region is modelled properly.

Experiments on transitional boundary layers with wake-induced unsteadiness

1991 ◽  
Vol 231 ◽  
pp. 229-256 ◽  
Author(s):  
X. Liu ◽  
W. Rodi
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Leading Edge ◽  
Clear Correlation ◽  
Hot Wire ◽  
Test Plate ◽  
Streamwise Location ◽  
Boundary Layer Development ◽  
Wake Passing

Hot-wire measurements were carried out in boundary layers developing along a flat plate over which wakes passed periodically. The wakes were generated by cylinders moving on a squirrel cage in front of the plate leading edge. The flow situation studied is an idealization of that occurring on turbomachinery blades where unsteady wakes are generated by the preceding row of blades. The influence of wake-passing frequency on the boundary-layer development and in particular on the transition processes was examined. The hot-wire signals were processed to yield ensemble-average values and the fluctuations could be separated into periodic and stochastic turbulent components. Hot-wire traces are reported as well as time variations of periodic and ensemble-averaged turbulent fluctuations and of the boundary-layer integral parameters, yielding a detailed picture of the flow development. The Reynolds number was relatively low so that in the limiting case of a boundary layer undisturbed by wakes this remained laminar over the full length of the test plate. When wakes passed over the plate, the boundary layer was found to be turbulent quite early underneath the free-stream disturbances due to the wakes, while it remained initially laminar underneath the undisturbed free-stream regions in between. The turbulent boundary-layer stripes underneath the disturbed free stream travel downstream and grow together so that the embedded laminar regions disappear and the boundary layer becomes fully turbulent. The streamwise location where this happens moves upstream with increasing wake-passing frequency, and a clear correlation could be determined in the experiments. The results are also reported in a mean Lagrangian frame by following fluid parcels underneath the disturbed and undisturbed free stream, respectively, as they travel downstream.

The generation of Tollmien-Schlichting waves by free-stream turbulence

1996 ◽  
Vol 312 ◽  
pp. 341-371 ◽  
Author(s):  
P. W. Duck ◽  
A. I. Ruban ◽  
C. N. Zhikharev
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Free Stream ◽  
Stokes Equations ◽  
Leading Edge ◽  
Wave Generation ◽  
Generation Process ◽  
Viscous Boundary Layer ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting

The phenomenon of Tollmien-Schlichting wave generation in a boundary layer by free-stream turbulence is analysed theoretically by means of asymptotic solution of the Navier-Stokes equations at large Reynolds numbers (Re → ∞). For simplicity the basic flow is taken to be the Blasius boundary layer over a flat plate. Free-stream turbulence is taken to be uniform and thus may be represented by a superposition of vorticity waves. Interaction of these waves with the flat plate is investigated first. It is shown that apart from the conventional viscous boundary layer of thickness O(Re−1/2), a ‘vorticity deformation layer’ of thickness O(Re−1/4) forms along the flat-plate surface. Equations to describe the vorticity deformation process are derived, based on multiscale asymptotic techniques, and solved numerically. As a result it is shown that a strong singularity (in the form of a shock-like distribution in the wall vorticity) forms in the flow at some distance downstream of the leading edge, on the surface of the flat plate. This is likely to provoke abrupt transition in the boundary layer. With decreasing amplitude of free-stream turbulence perturbations, the singular point moves far away from the leading edge of the flat plate, and any roughness on the surface may cause Tollmien-Schlichting wave generation in the boundary layer. The theory describing the generation process is constructed on the basis of the ‘triple-deck’ concept of the boundary-layer interaction with the external inviscid flow. As a result, an explicit formula for the amplitude of Tollmien-Schlichting waves is obtained.

scholarly journals A class of exact Navier–Stokes solutions for homogeneous flat-plate boundary layers and their linear stability

2014 ◽  
Vol 752 ◽  
pp. 462-484 ◽  
Author(s):  
Michael O. John ◽  
Dominik Obrist ◽  
Leonhard Kleiser
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Linear Stability ◽  
Boundary Layers ◽  
Stokes Equations ◽  
Plate Boundary ◽  
Navier Stokes ◽  
Transition Prediction ◽  
Neutral Curves ◽  
Tollmien Schlichting

AbstractWe introduce a new boundary layer formalism on the basis of which a class of exact solutions to the Navier–Stokes equations is derived. These solutions describe laminar boundary layer flows past a flat plate under the assumption of one homogeneous direction, such as the classical swept Hiemenz boundary layer (SHBL), the asymptotic suction boundary layer (ASBL) and the oblique impingement boundary layer. The linear stability of these new solutions is investigated, uncovering new results for the SHBL and the ASBL. Previously, each of these flows had been described with its own formalism and coordinate system, such that the solutions could not be transformed into each other. Using a new compound formalism, we are able to show that the ASBL is the physical limit of the SHBL with wall suction when the chordwise velocity component vanishes while the homogeneous sweep velocity is maintained. A corresponding non-dimensionalization is proposed, which allows conversion of the new Reynolds number definition to the classical ones. Linear stability analysis for the new class of solutions reveals a compound neutral surface which contains the classical neutral curves of the SHBL and the ASBL. It is shown that the linearly most unstable Görtler–Hämmerlin modes of the SHBL smoothly transform into Tollmien–Schlichting modes as the chordwise velocity vanishes. These results are useful for transition prediction of the attachment-line instability, especially concerning the use of suction to stabilize boundary layers of swept-wing aircraft.

Sign in / Sign up

Export Citation Format

Share Document