Comparative Life-Cycle Assessment of Aquifer Thermal Energy Storage Integrated with in Situ Bioremediation of Chlorinated Volatile Organic Compounds

2020 ◽  
Vol 54 (5) ◽  
pp. 3039-3049
Author(s):  
Zhuobiao Ni ◽  
Yue Wang ◽  
Yafei Wang ◽  
Shaoqing Chen ◽  
Manxi Xie ◽  
...  
2021 ◽  
Author(s):  
Boyan Meng ◽  
Christof Beyer ◽  
Olaf Kolditz ◽  
Haibing Shao

<p>In urban areas where the shallow subsurface is used for thermal energy storage (TES), interactions between the introduced heat and groundwater pollution caused by toxic organic contaminants can be expected. Temperature elevations may affect the transfer of these volatile organic compounds (VOCs) from the groundwater to the unsaturated zone, creating a redistribution or release of the contaminants in/from the subsurface environment. Such effects are particularly important considering the intersection of the unsaturated zone with the land surface and the remediation capacity of polluted aquifers. In this work, a non-isothermal multi-component two-phase flow model was developed to investigate the thermally induced volatilization and migration of the VOCs in contaminated aquifers. The numerical model, which is implemented in the open source framework <em>OpenGeoSys</em>-6, is able to simulate temperature-dependent mass and heat transfer processes in partially-saturated soils while allowing for phase change. Verification of the model against various benchmark problems and experimental data showed good accuracy. Simulation results revealed that a temperature-driven migration of dissolved trichloroethylene (TCE) from the groundwater to the drier regions of the unsaturated zone can be observed in general. A temperature increase of 20 K around the borehole led to a maximum decline of the total TCE concentration by 63% assuming zero TCE concentration at the soil surface. In addition, the TCE concentration distribution varied considerably with the depth-dependent water saturation. Further investigations were carried out to study the effects of different parameters, e.g. groundwater velocity, contaminant type and boundary conditions. Based on our analysis, the planning of subsurface TES systems can be optimized to account for the possible interactions with pre-existing groundwater contamination.</p><p><strong>References:</strong></p><p>Kolditz, O., Bauer, S., Bilke, L., Böttcher, N., Delfs, J. O., Fischer, T., ... & Zehner, B. (2012). OpenGeoSys: an open-source initiative for numerical simulation of thermo-hydro-mechanical/chemical (THM/C) processes in porous media. <em>Environmental Earth Sciences</em>, <em>67</em>(2), 589-599.</p>


2021 ◽  
Vol 248 ◽  
pp. 114787
Author(s):  
D. Le Roux ◽  
Y. Lalau ◽  
B. Rebouillat ◽  
P. Neveu ◽  
R. Olivès

2021 ◽  
Vol 285 ◽  
pp. 116378
Author(s):  
Giuseppe Di Florio ◽  
Edoardo Gino Macchi ◽  
Luigi Mongibello ◽  
Maria Camilla Baratto ◽  
Riccardo Basosi ◽  
...  

Procedia CIRP ◽  
2018 ◽  
Vol 69 ◽  
pp. 206-211 ◽  
Author(s):  
Rafael Horn ◽  
Matthias Burr ◽  
Dominik Fröhlich ◽  
Stefan Gschwander ◽  
Michael Held ◽  
...  

Author(s):  
John J. Burkhardt ◽  
Garvin Heath ◽  
Craig Turchi

This study evaluates the environmental impacts of a hypothetical 103 megawatt, parabolic trough, wet-cooled concentrating solar power (CSP) plant in the U.S. Southwest with 6.3 hours of thermal energy storage by means of a hybrid life cycle assessment. Life cycle greenhouse gas emissions, cumulative energy demand, and water consumption associated with the manufacture, construction, operation, dismantling, and disposal of the power plant are evaluated and disaggregated by major systems and components. The reference CSP plant emits 26 g CO2eq per kWh of electrical output across its life cycle, cumulatively demands 0.43 MJeq/kWh of energy, and consumes 4.7 L/kWh of water. The majority of water is consumed by the power block for evaporative cooling. Sensitivity analyses are performed on several key assumptions and design elements: the configuration of the thermal energy storage system (i.e., thermocline), the heat transfer fluid, the nitrate salts, the cooling system type (i.e., dry-cooled) and the energy required for construction and end-of-life dismantling. Our base case results are robust to alternative assumptions regarding the heat transfer fluid and energy required for construction and dismantling; however, the total life cycle impacts are strongly influenced by the type of cooling system and nitrate salts employed.


Sign in / Sign up

Export Citation Format

Share Document