Electric insulator

AccessScience ◽  
2015 ◽  
Keyword(s):  
2021 ◽  
Vol 651 (2) ◽  
pp. 022037
Author(s):  
Kai Guo ◽  
Bo Jiang ◽  
Peng Zhao ◽  
Yaping Wu ◽  
Shuang Tian ◽  
...  
Keyword(s):  

2021 ◽  
Author(s):  
Sabarinathan Palaniyappan ◽  
Annamalai Veiravan ◽  
Rajkumar Kaliyamoorthy ◽  
Vishal Kumar

Abstract Increasing demand and resource overuse has prompted the exploration of spent secondary materials as a primary raw material for a variety of applications, leading to a more sustainable environment. Spent electric grid ceramic insulator, one of the waste materials of ceramic industry has a good hardness and strength. It can be reused as value added material in Abrasive Water Jet Machining (AWJM) industry. This present work deals with conversion of electric insulator rejects (EIR) into a cost-effective replacement material for abrasive water jet machining process. Mechanical crushing method is opted to generate the abrasive grit for the machining process. Grit generation pattern and the friability of the electric insulator rejects were determined experimentally. The results indicate that the friability of the processed electric insulator rejects is comparable with the commercially available garnet abrasive. Geometric parameters such as sphericity, elongation ratio, and shape factor for the processed electric insulator rejects were studied using scanning electron microscopy. The machining performance indicators for standard aluminium material such as volume of material removal, kerf angle, surface roughness and cutting width were measured for electric insulator rejects and compared with existing garnet abrasive grain. The experimental results of newly generated electric insulator reject abrasive were matched with performance indicators of the garnet abrasive. The observed deviation was lower proving that it can be used as alternative abrasive in the abrasive jet machining process. Cost analysis and recycling ability predict the economical usability of the newly generated abrasives.


1961 ◽  
Vol 201 (4) ◽  
pp. 587-592 ◽  
Author(s):  
Paul Bass ◽  
Charles F. Code ◽  
Edward H. Lambert

In preparation for a study of the electric activity in the wall of the gastroduodenal junction in unanesthetized trained dogs, the pyloric portion of the stomach (antrum), the pylorus, and the first portion of the duodenum were exteriorized surgically. When the animals were fully recovered, needle electrodes were inserted into the wall of the bowel for the detection of electric activity. The pylorus was found to act as an "electric insulator" between the stomach and the duodenum. The basic electric rhythm (BER) and the fast or spike activity detected in both the pyloric canal and the duodenal bulb became attenuated in the pylorus and usually disappeared in it. The BER of the antrum had a mean frequency of 4.4 cycle/min and spike potentials sometimes were associated with it. The frequency of the BER in the duodenal bulb was the same as in the duodenum but its voltage was less and its form more irregular. Spike potentials in the bulb occurred during a greater portion of the BER and had a greater tendency to distort the BER than in the more distal duodenum.


2006 ◽  
Vol 48 ◽  
pp. 127-132
Author(s):  
O.I. Raychenko ◽  
T.I. Istomina ◽  
R.O. Morozova ◽  
I.A. Morozov ◽  
O.V. Derev'yanko

A number of installations for electric discharge sintering of powder materials is developed. There are installations in which energy is delivered by following currents: 1) superposition of the direct and alternating (with frequency up 7900 Hz) currents, 2) alternating current (50 Hz). The sintering is carried out in conductive (graphite) moulds. The sintering is often done in thermal and electric insulator moulds (for example, ceramic on Si3N4 base, asbestos cement). At sintering of metal-diamond composition in insulator moulds metallic electrodespunches (steel) are used. Such a variant of sintering allows one its duration to short from ~900 s down to ~60–150 s. This ensures complete safety of dimensions and operating characteristics of diamond grains. The technologies of various diamond elements for tools for treatment of glasses and soft stones (stone saws, tools in forms of tablets, rings). The preliminary pressure which is applied to powder sample simultaneously with current was equal to ~10 MPa (~100 kg/cm2). The end pressure was equal to ~100 MPa (~1000 kg/cm2). The current density was equal to ~700– 1200 A/cm2. Tests of diamond tablets (diamond 20/14 mkm, binder 80 % Cu+20 % Sn) at grinding of glass had shown: the abrasivity of tablets with common diamonds is equal to ~50 g/(cm2 min), and abrasivity in case with diamonds annealed in hydrogen is equal to ~70 g/(cm2 min).


1990 ◽  
Vol 110 (5) ◽  
pp. 561-569 ◽  
Author(s):  
Keiji Nakamura ◽  
Chobei Yamabe ◽  
Kenji Horii

2017 ◽  
Vol 265 ◽  
pp. 496-500
Author(s):  
A.N. Demidov ◽  
M.A. Karimbekov ◽  
A.Yu. Marchenkov

The mechanical properties investigation results obtained by tension and indentation tests of RIP (resin impregnated paper) electric insulator are presented. Tension and indentation tests of the RIP electric insulation material in wide temperature range are conducted. The common relations between strength and temperature as well as between hardness and temperature for the RIP electric insulation are established. The ratio of ultimate tensile strength to Brinell hardness is performed to be constant (about 1/3) irrespective of temperature, that means a possibility of the RIP electric insulation mechanical properties evaluation by the instrumented indentation test.


Sign in / Sign up

Export Citation Format

Share Document