CFD investigation of effect of relative roughness height on Nusselt number and friction factor in an artificially roughened solar air heater

2015 ◽  
Vol 38 (4) ◽  
pp. 494-502 ◽  
Author(s):  
Anil Singh Yadav
Keyword(s):  
Nusselt Number ◽  
Friction Factor ◽  
Roughness Height ◽  
Solar Air Heater ◽  
Air Heater ◽  
Relative Roughness

scholarly journals CFD Analysis to Study Effect of Circular Vortex Generator Placed in Inlet Section to Investigate Heat Transfer Aspects of Solar Air Heater

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Vipin B. Gawande ◽  
A. S. Dhoble ◽  
D. B. Zodpe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Vortex Generator ◽  
Inlet Section ◽  
Solar Air Heater ◽  
Cfd Analysis ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness

CFD analysis of 2-dimensional artificially roughened solar air heater duct with additional circular vortex generator, inserted in inlet section is carried out. Circular transverse ribs on the absorber plate are placed as usual. The analysis is done to investigate the effect of inserting additional vortex generator on the heat transfer and flow friction characteristics inside the solar air heater duct. This investigation covers relative roughness pitch in the range of 10 ≤P/e≤ 25 and relevant Reynolds numbers in the range of 3800 ≤ Re ≤ 18000. Relative roughness height (e/D) is kept constant as 0.03 for analysis. The turbulence created due to additional circular vortex generator increases the heat transfer rate and at the same time there is also increase in friction factor values. For combined arrangement of ribs and vortex generator, maximum Nusselt number is found to be 2.05 times that of the smooth duct. The enhancement in Nusselt number with ribs and additional vortex generator is found to be 1.06 times that of duct using ribs alone. The maximum increase in friction factor with ribs and circular vortex generator is found to be 2.91 times that of the smooth duct. Friction factor in a combined arrangement is 1.114 times that in a duct with ribs alone on the absorber plate. The augmentation in Thermal Enhancement Factor (TEF) with vortex generator in inlet section is found to be 1.06 times more than with circular ribs alone on the absorber plate.

scholarly journals Nusselt Number and Friction Factor Correlations Development for Arc-Shape Apex Upstream Artificial Roughness in Solar Air Heater

2021 ◽  
Author(s):  
Mukesh Kumar Sahu ◽  
Manjeet Kharub ◽  
Mahalingam Murugesan Matheswaran
Keyword(s):  
Nusselt Number ◽  
Friction Factor ◽  
Roughness Element ◽  
Circular Cross Section ◽  
Solar Air Heater ◽  
Enhancement Ratio ◽  
Air Heater ◽  
Relative Roughness ◽  
Evaluation Of Performance ◽  
Arc Shape

Abstract In the present work an outdoor experimental investigation for solar air heater with arc-shaped apex-upstream flow by the use of circular cross section wires as roughness elements has been carried out. The roughness-element have been expressed in non-dimensionalizing geometric parameters as relative roughness-pitch (P/e), relative roughness-height (e/D) and flow attack-angle (α/60), and the range of these parameters varies from 8 to 15, 0.0454, and 0.75 to 1.25, respectively. For evaluation of performance of the roughened SAH, a novel parameter has been proposed and introduced in the present investigation which is Thermo-Hydraulic Improvement Parameter (THIP). With the use of present roughness geometry, considerably Nusselt number enhancement ratio (NNER) and friction factor enhancement ratio (FFER) have been observed. The maximum NNER and FFER values obtained experimentally is about 2.83 and 1.79 times, respectively. While, the maximum THIP has been obtained 157.49% higher than the smooth SAH. Using the experimental results correlations for the output parameters (Nusselt number and friction factor) as a function of input parameters (flow and roughness) have been developed.

scholarly journals Computational fluid dynamics analysis of a V-rib with gap roughened solar air heater

2018 ◽  
Vol 22 (2) ◽  
pp. 963-972 ◽  
Author(s):  
Jitesh Rana ◽  
Anshuman Silori ◽  
Rajesh Maithani ◽  
Sunil Chamoli
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Friction Factor ◽  
Angle Of Attack ◽  
Solar Air Heater ◽  
Computational Domain ◽  
Cfd Analysis ◽  
Air Heater ◽  
Relative Roughness ◽  
Computational Fluid Dynamics Analysis

A CFD analysis of a solar air heater has been carried out using V-shaped ribs as artificial roughness on the absorber plate. The relative roughness pitch, P/e = 6-12, Reynolds number of 3800-18000, relative roughness height, e/D = = 0.042, and angle of attack, ? = 30?-75?, have been selected as design variables of V-shaped rib for analysis. The ANSYS FLUENT 15.0 with renormalization group k-? turbulence model is selected for the analysis of computational domain of solar air heater. The enhancement of Nusselt number and friction factor with Reynolds number for different values of a relative roughness pitch are presented and discussed by CFD analysis. The effect of angle of attack and Reynolds number on enhancement of Nusselt number and friction factor is also presented. The optimum value of rib configuration based on constant pumping power requirement has been derived using thermohydraulic performance parameter and has been found maximum at angle of attack of 60? and P/e = 10.

Three-Dimensional Thermo-Hydraulic Analysis of Solar Air Heater With Equilateral Prism-Shaped Rib Roughness

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Inzamam Ahmad ◽  
N. H. Khan ◽  
M. A. Hassan ◽  
M. K. Paswan
Keyword(s):  
Nusselt Number ◽  
Friction Factor ◽  
Average Nusselt Number ◽  
Three Dimensional ◽  
Hydraulic Performance ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Flow Friction ◽  
Air Heater ◽  
Relative Roughness

Abstract Thermal transport and flow friction characteristics due to roughness on the absorber plate of solar air heater are evaluated by applying three-dimensional finite volume based code. Renormalization group (RNG) k–ɛ model is employed to capture the turbulent nature of the flow. The effect of equilateral prism-shaped rib roughness geometrical parameters in terms of relative roughness height (e/D) and relative roughness pitch (p/e) on heat transfer and flow friction is analyzed. Further, the effect of flow parameter, Re in the range of 4000–18,000 is also explored. Results are elucidated in terms of average Nusselt number, friction factor, turbulent kinetic energy, and eddy dissipation. Results are compared with a smooth absorber plate solar air heater. Thermo-hydraulic performance of the roughened solar air heater is analyzed. Noteworthy augmentation in heat transport is obtained. The thermal enhancement factor is calculated for optimal performance and found to vary from 1.7 to 3.5. However, friction factor and pressure loss for roughened plate is significantly higher than its smooth counterpart. The pressure drop across the test section increases with the rise in roughness height due to flow obstruction. A minimum value of the friction factor enhancement ratio worth 2.13 is obtained. Enhancement in thermal transport and pressure losses are combined by introducing a thermo-hydraulic performance factor (THHP). For the range of parameters investigated, the optimum value of the thermo-hydraulic performance factor is found to be 3.41. Correlations for average Nusselt number and friction factor are offered at the end.

Impact of relative roughness height on the materialistic thermohydraulic performance of the multiple V-ribbed solar air heater

2020 ◽  
Vol 26 ◽  
pp. 1845-1849
Author(s):  
Gagan Bansal ◽  
Chandra Kishore ◽  
Vaishally Dogra ◽  
Amit Bansal ◽  
Rahul Keshari
Keyword(s):  
Roughness Height ◽  
Solar Air Heater ◽  
Air Heater ◽  
Relative Roughness

Heat Transfer and Friction Factor Correlations for Solar Air Heater With Gap in V-Rib With Symmetrical Gap and Staggered Ribs

2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Sumer Singh Patel ◽  
Atul Lanjewar
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Smooth Surface ◽  
Heat Transfer Analysis ◽  
Operating Parameters ◽  
Solar Air Heater ◽  
Gap Size ◽  
Maximum Enhancement ◽  
Air Heater ◽  
Relative Roughness

Abstract The present experimental study is concerned with heat transfer analysis of air flowing in solar air heater duct with a gap in V-rib with symmetrical gap and staggered ribs geometry. The investigated parameters are Reynolds number (Re) of 4000–14,000, relative roughness pitch (p/e) of 12, relative roughness height (e/Dh) of 0.043, angle of attack (α) of 60 deg, relative staggered rib pitch (p′/p) of 0.65, relative gap size (g/e) of 4, relative staggered rib size (r/e) of 4, relative gap position of additional gap in each symmetrical rib elements (d/w) of 0.65, relative gap size of additional gap in each symmetrical rib elements (g′/e) of 1, number of main gaps (Ng) of 1, 2, 3, 4, and number of additional gap (ng) varying from 1 to 5. Fourteen roughened absorber plates were tested. The maximum enhancement in Nusselt number (Nu) and friction factor (f) was 2.34 and 2.79 times that of smooth surface corresponding to the number of main gaps (Ng) of 4 with the number of additional gaps (ng) of 4. The performance of the gap in V-rib with symmetrical gap and staggered rib geometry has been compared with the existing latest V-rib geometry and smooth surface. The proposed gap in V-rib with symmetrical gap and staggered ribs geometry has a better performance than the existing latest V-rib geometry. The following correlations have been developed for heat transfer and friction factor in terms of roughness and operating parameters. Heat transfer:Nur=0.0073(Re)0.9788(Ng)0.2790(ng)0.0184exp[−0.1678(ln(Ng))2]exp[−0.0129(ln(ng))2] Friction factor:fr=0.0477(Re)−0.0678(Ng)0.5919(ng)−0.0562exp[−0.4922(ln(Ng))2]exp[−0.0487(ln(ng))2]

Experimental Investigation on Thermal Performance in Three-Sided Solar Air Heaters Having an Alignment of Multi-v and Transverse Wire Roughness on the Absorber Plate

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Dhananjay Kumar ◽  
Laljee Prasad
Keyword(s):  
Thermal Performance ◽  
Thermal Efficiency ◽  
Roughness Height ◽  
Space Heating ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness ◽  
Operational Constraints

Abstract The use of artificial roughness is an efficient and commercial way to appreciate the thermal performance from the collector to the air in solar air heater ducts, for numerous applications such as space-heating, crop-drying, and seasoning of timber industrial purpose. In this paper, the tentative inquiry on thermal enactment using new-fangled of three-sided roughened quadrilateral duct solar air heater having an alignment of multiple-v and transverse wire is performed and compared the outcomes with smooth duct air heater under similar operational circumstances. The modification of an arrangement and operational constraints is inspected within the restrictions, the moral of four-sided duct aspect ratio (W/H) = 8, the Reynolds number occupied from 3000 to 12,000, fraction of pitch to roughness height, P/e in the range of 10–25; ratio of roughness height to hydraulic diameter, e/D in the range of 0.018–0.042; at flow attack angle, α = 60 deg for constant moral of relative roughness width, (W/w) = 6. The augmentation on thermal efficiency in three-sided rugged duct is found to be 23–86% when compared to smooth duct, and the maximum thermal efficiency can occur at P/e = 10 and e/D = 0.042. The enhancement in air temperature flowing under three-sided roughened duct is found to be 49.27% more than that of a smooth duct. The instant innovative form of three-sided roughened solar air warmer would be preferable to those of a smooth solar air heater with respect to heat assignment.

Sign in / Sign up

Export Citation Format

Share Document