Starch Flow Behavior Alone And Under Different Glidants Action Using The Shear Cell Method

Author(s):  
Paulo J. Salústio ◽  
Maria F. Monteiro ◽  
Telmo Nunes ◽  
José P. Sousa e Silva ◽  
Paulo J. Costa
Keyword(s):  
Author(s):  
M. A. Kabir ◽  
C. F. Higgs ◽  
M. R. Lovell ◽  
V. Jasti ◽  
M. C. Marinack

Explicit finite element method modeling of granular flow behavior in an annular shear cell has been studied and presented in this paper. The explicit finite element method (FEM) simulations of granular flow in an annular shear cell with around 1633 particles were performed, where the inner wheel rotated at a very high speed and the outer disk remained stationary. The material properties of the particles and the outer wheel were defined as elastic steel whereas the inner wheel was elastic aluminum. In this investigation, the explicit FEM model mimicked granular flow in an experimental set up where the inner wheel was rotated at a speed of 240 rpm. The FEM results for shearing motion and solid fraction were compared with experimental results from a granular shear cell.


Author(s):  
Paulo José Salústio ◽  
Mafalda Machado ◽  
Telmo Nunes ◽  
José Paulo Sousa e Silva ◽  
Paulo Cardoso Costa

2019 ◽  
Vol 25 (2) ◽  
pp. 237-244 ◽  
Author(s):  
Paulo José Salústio ◽  
Cláudia Inácio ◽  
Telmo Nunes ◽  
José Paulo Sousa e Silva ◽  
Paulo Cardoso Costa

2020 ◽  
Vol 25 (6) ◽  
pp. 686-693 ◽  
Author(s):  
Paulo José Salústio ◽  
Mafalda Machado ◽  
Telmo Nunes ◽  
José Paulo Sousa e Silva ◽  
Paulo Cardoso Costa

2021 ◽  
Vol 249 ◽  
pp. 01001
Author(s):  
Sandip Mandal ◽  
Adrien Gans ◽  
Maxime Nicolas ◽  
Olivier Pouliquen

Cohesive granular media have broad applications in industries. However, our understanding of their flow behavior is still limited compared to dry granular media, although rich knowledge about their static and plastic properties has been gained. In this paper, we provide some insights into the flow behavior of cohesive granular media from our recent numerical studies using an inclined plane and a plane shear cell. We evidence that the cohesive nature of flows is significantly affected by material properties of the particles like stiffness and inelasticity in addition to the inter-particle adhesion and introduce the concept of “effective” adhesion, which incorporates the effects of these three variables. We propose constitutive relations involving dimensionless inertial number and “effective” cohesion number, based on the “effective” adhesion to describe the rheology. We also show that increasing adhesion increases the hysteresis in granular media, evidencing the existence of a prominent shear weakening branch in the friction coefficient versus inertial number rheological curve. Moreover, we reveal that this increasing hysteresis gives rise to the increasing occurrence of shear banding instability, pointing to the increasing possibility of jamming in cohesive granular media. Finally, we present a promising experimental approach to investigate the flow behavior of cohesive granular materials, based on a simple method of preparing a long time stable medium with a controlled adhesion between particles.


Netsu Bussei ◽  
2005 ◽  
Vol 19 (3) ◽  
pp. 147-152
Author(s):  
Tomoharu Fukazawa ◽  
Tadahiko Masaki ◽  
Toshio Itami ◽  
Yuki Watanabe

2020 ◽  
Vol 117 (6) ◽  
pp. 619
Author(s):  
Rui Xu ◽  
Haitao Ling ◽  
Haijun Wang ◽  
Lizhong Chang ◽  
Shengtao Qiu

The transient multiphase flow behavior in a single-strand tundish during ladle change was studied using physical modeling. The water and silicon oil were employed to simulate the liquid steel and slag. The effect of the turbulence inhibitor on the slag entrainment and the steel exposure during ladle change were evaluated and discussed. The effect of the slag carry-over on the water-oil-air flow was also analyzed. For the original tundish, the top oil phase in the impact zone was continuously dragged into the tundish bath and opened during ladle change, forming an emulsification phenomenon. By decreasing the liquid velocities in the upper part of the impact zone, the turbulence inhibitor decreased considerably the amount of entrained slag and the steel exposure during ladle change, thereby eliminating the emulsification phenomenon. Furthermore, the use of the TI-2 effectively lowered the effect of the slag carry-over on the steel cleanliness by controlling the movement of slag droplets. The results from industrial trials indicated that the application of the TI-2 reduced considerably the number of linear inclusions caused by ladle change in hot-rolled strip coils.


Sign in / Sign up

Export Citation Format

Share Document