Effect of Fluid Inertia on Force Coefficients for the Long Squeeze Film Damper

1988 ◽  
Vol 31 (3) ◽  
pp. 370-375 ◽  
Author(s):  
Luis A. San Andrés
Keyword(s):  
Squeeze Film ◽  
Fluid Inertia ◽  
Squeeze Film Damper ◽  
Force Coefficients

Analysis of Short Squeeze Film Dampers With a Central Groove

1992 ◽  
Vol 114 (4) ◽  
pp. 659-664 ◽  
Author(s):  
Luis A. San Andres
Keyword(s):  
Squeeze Film ◽  
Inertia Force ◽  
Dynamic Force ◽  
Fluid Inertia ◽  
Dynamic Flow ◽  
Low Frequencies ◽  
Squeeze Film Damper ◽  
Force Coefficients ◽  
Squeeze Film Dampers ◽  
Combined Action

A novel analysis for the dynamic force response of a squeeze film damper with a central feeding groove considers the dynamic flow interaction between the squeeze film lands and the feeding groove. For small amplitude centered motions and based on the short bearing model, corrected values for the damping and inertia force coefficients are determined. Correlations with existing experimental evidence is excellent. Analytical results show that the grooved-damper behaves at low frequencies as a single land damper. Dynamic force coefficients are determined to be frequency dependent. Analytical predictions show that the combined action of fluid inertia and groove volume—liquid compressibility affects the force coefficients for dynamic excitation at large frequencies.

Squeeze Film Damper Suppression of Thermal Bow: Morton Effect Instability

2020 ◽  
Author(s):  
Dongil Shin ◽  
Alan B. Palazzolo ◽  
Xiaomeng Tong
Keyword(s):  
Squeeze Film ◽  
Viscous Heating ◽  
Fluid Inertia ◽  
Euler Beam ◽  
Nonlinear Simulation ◽  
Squeeze Film Damper ◽  
Morton Effect ◽  
Tilting Pad ◽  
Tilting Pad Journal Bearing ◽  
Rotor Model

Abstract The Morton Effect (ME) is a synchronous vibration problem in turbomachinery caused by the non-uniform viscous heating around the journal circumference, and its resultant thermal bow and ensuing synchronous vibration. This paper treats the unconventional application of the SFD for the mitigation of ME-induced vibration. Installing a properly designed squeeze film damper (SFD) may change the rotor’s critical speed location, damping and deflection shape, and thereby suppress the vibration caused by the ME. The effectiveness of the SFD on suppressing the ME is tested via linear and nonlinear simulation studies employing a 3D thermo-hydrodynamic (THD) tilting pad journal bearing, and a flexible, Euler beam rotor model. The example rotor model is for a compressor that experimentally exhibited an unacceptable vibration level along with significant journal differential heating near 8,000 rpm. The SFD model includes fluid inertia and is installed on the non-drive end bearing location where the asymmetric viscous heating of the journal is highest. The influence of SFD cage stiffness is evaluated.

scholarly journals Squeeze-Film Damper Technology: Part 1 — Prediction of Finite Length Damper Performance

1983 ◽  
Author(s):  
J. W. Lund ◽  
A. J. Smalley ◽  
J. A. Tecza ◽  
J. F. Walton
Keyword(s):  
Finite Length ◽  
Gas Turbines ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Inertia Effects ◽  
Strongly Coupled ◽  
Squeeze Film Damper ◽  
Rotor Systems ◽  
Squeeze Film Dampers ◽  
Calculation Results

Squeeze-film dampers are commonly used in gas turbine engines and have been applied successfully in a great many new designs, and also as retrofits to older engines. Of the mechanical components in gas turbines, squeeze-film dampers are the least understood. Their behavior is nonlinear and strongly coupled to the dynamics of the rotor systems on which they are installed. The design of these dampers is still largely empirical, although they have been the subject of a large number of past investigations. To describe recent analytical and experimental work in squeeze-film damper technology, two papers are planned. This abstract outlines the first paper, Part 1, which concerns itself with squeeze-film damper analysis. This paper will describe an analysis method and boundary conditions which have been developed recently for modelling dampers, and in particular, will cover the treatment of finite length, feed and drain holes and fluid inertia effects, the latter having been shown recently to be of great importance in predicting rotor system behavior. A computer program that solves the Reynolds equation for the above conditions will be described and sample calculation results presented.

Study of Static Fluid Forces in a Squeeze Film Damper with a Circumferential Groove

1995 ◽  
Vol 209 (4) ◽  
pp. 263-274
Author(s):  
J X Zhang
Keyword(s):  
Fluid Pressure ◽  
Squeeze Film ◽  
Fluid Inertia ◽  
Traditional Use ◽  
Fluid Force ◽  
Squeeze Film Damper ◽  
Fluid Forces ◽  
Supply Pressure ◽  
Static Fluid ◽  
Approximate Expressions

Approximate expressions are obtained for static fluid pressure and force for a centrally grooved squeeze film damper (SFD) resting at an equilibrium position without vibration. The analysis shows that, to some extent, grooved SFDs may share some characteristics with hydrostatic bearings, due to the existence of the lubricant supply pressure. Thus static fluid force and hence oil stiffness may exist in SFDs, in addition to the conventional inertial and damping coefficients for SFDs. This paper is solely focused on the static fluid forces and oil stiffness generated in an SFD with a finite length groove. Flow continuity is used at the centre of the groove, which takes into account the effects of the inlet oil flowrate and oil supply pressure. This use of flow continuity differs substantially from the traditional use of constant pressure in the central groove, and it provides better results. At the interface between the groove and the thin film land, a step bearing model with ignored fluid inertia is employed. It is verified by both the theory and previous experiments that the static fluid force and stiffness are linearly proportional to both the lubricant supply pressure and the eccentricity ratio of the SFD journal.

Squeeze Film Damper Suppression of Thermal Bow-Morton Effect Instability

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Dongil Shin ◽  
Alan B. Palazzolo ◽  
Xiaomeng Tong
Keyword(s):  
Three Dimensional ◽  
Squeeze Film ◽  
Viscous Heating ◽  
Fluid Inertia ◽  
Euler Beam ◽  
Nonlinear Simulation ◽  
Squeeze Film Damper ◽  
Morton Effect ◽  
Tilting Pad Journal Bearing ◽  
Rotor Model

Abstract The Morton effect (ME) is a synchronous vibration problem in turbomachinery caused by the nonuniform viscous heating around the journal circumference, and its resultant thermal bow (TB) and ensuing synchronous vibration. This paper treats the unconventional application of the SFD for the mitigation of ME-induced vibration. Installing a properly designed squeeze film damper (SFD) may change the rotor's critical speed location, damping, and deflection shape, and thereby suppress the vibration caused by the ME. The effectiveness of the SFD on suppressing the ME is tested via linear and nonlinear simulation studies employing a three-dimensional (3D) thermohydrodynamic (THD) tilting pad journal bearing (TJPB), and a flexible, Euler beam rotor model. The example rotor model is for a compressor that experimentally exhibited an unacceptable vibration level along with significant journal differential heating near 8000 rpm. The SFD model includes fluid inertia and is installed on the nondrive end bearing location where the asymmetric viscous heating of the journal is highest. The influence of SFD cage stiffness is evaluated.

Forced Response of a Squeeze Film Damper and Identification of Force Coefficients From Large Orbital Motions

2004 ◽  
Vol 126 (2) ◽  
pp. 292-300 ◽  
Author(s):  
Luis San Andre´s ◽  
Oscar De Santiago
Keyword(s):  
Excitation Frequency ◽  
Air Entrainment ◽  
Forced Response ◽  
Effective Length ◽  
Single Frequency ◽  
Squeeze Film ◽  
Inertia Force ◽  
Damping Force ◽  
Squeeze Film Damper ◽  
Force Coefficients

Experimentally derived damping and inertia force coefficients from a test squeeze film damper for various dynamic load conditions are reported. Shakers exert single frequency loads and induce circular and elliptical orbits of increasing amplitudes. Measurements of the applied loads, bearing displacements and accelerations permit the identification of force coefficients for operation at three whirl frequencies (40, 50, and 60 Hz) and increasing lubricant temperatures. Measurements of film pressures reveal an early onset of air ingestion. Identified damping force coefficients agree well with predictions based on the short length bearing model only if an effective damper length is used. A published two-phase flow model for air entrainment allows the prediction of the effective damper length, and which ranges from 82% to 78% of the damper physical length as the whirl excitation frequency increases. Justifications for the effective length or reduced (flow) viscosity follow from the small through flow rate, not large enough to offset the dynamic volume changes. The measurements and analysis thus show the pervasiveness of air entrainment, whose effect increases with the amplitude and frequency of the dynamic journal motions. Identified inertia coefficients are approximately twice as large as those derived from classical theory.

Sign in / Sign up

Export Citation Format

Share Document