Numerical and experimental predictions of formability parameters in tube hydroforming process

2021 ◽  
pp. 1-17
Author(s):  
Bapurao G. Marlapalle ◽  
Rahulkumar S. Hingole
Keyword(s):  
Tube Hydroforming ◽  
Hydroforming Process

Optimization of Tube Hydroforming Process Using Probabilistic Constraints on Failure Modes

2011 ◽  
Vol 62 ◽  
pp. 21-35 ◽  
Author(s):  
Anis Ben Abdessalem ◽  
A. El Hami
Keyword(s):  
Failure Modes ◽  
High Reliability ◽  
Thickness Distribution ◽  
Tube Hydroforming ◽  
Forming Limit Diagram ◽  
Plastic Instability ◽  
Probabilistic Constraints ◽  
Forming Limit ◽  
Reliability Based Design ◽  
Hydroforming Process

In metal forming processes, different parameters (Material constants, geometric dimensions, loads …) exhibits unavoidable scatter that lead the process unreliable and unstable. In this paper, we interest particularly in tube hydroforming process (THP). This process consists to apply an inner pressure combined to an axial displacement to manufacture the part. During the manufacturing phase, inappropriate choice of the loading paths can lead to failure. Deterministic approaches are unable to optimize the process with taking into account to the uncertainty. In this work, we introduce the Reliability-Based Design Optimization (RBDO) to optimize the process under probabilistic considerations to ensure a high reliability level and stability during the manufacturing phase and avoid the occurrence of such plastic instability. Taking account of the uncertainty offer to the process a high stability associated with a low probability of failure. The definition of the objective function and the probabilistic constraints takes advantages from the Forming Limit Diagram (FLD) and the Forming Limit Stress Diagram (FLSD) used as a failure criterion to detect the occurrence of wrinkling, severe thinning, and necking. A THP is then introduced as an example to illustrate the proposed approach. The results show the robustness and efficiency of RBDO to improve thickness distribution and minimize the risk of potential failure modes.

scholarly journals Numerical investigation of plastic flow and residual stresses generated in hydroformed tubes

2021 ◽  
pp. 146442072198974
Author(s):  
A Ktari ◽  
A Abdelkefi ◽  
N Guermazi ◽  
P Malecot ◽  
N Boudeau
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Plastic Flow ◽  
Tube Hydroforming ◽  
Three Dimensional ◽  
Element Model ◽  
Tube Cross Section ◽  
Straight Wall ◽  
Hydroforming Process

During tube hydroforming process, the friction conditions between the tube and the die have a great importance on the material plastic flow and the distribution of residual stresses of the final component. Indeed, a three-dimensional finite element model of a tube hydroforming process in the case of square section die has been performed, using dynamic and static approaches, to study the effect of the friction conditions on both plastic flow and residual stresses induced by the process. First, a comparative study between numerical and experimental results has been carried out to validate the finite element model. After that, various coefficients of friction were considered to study their effect on the thinning phenomenon and the residual stresses distribution. Different points have been retained from this study. The thinning is located in the transition zone cited between the straight wall and the corner zones of hydroformed tube due to the die–tube contact conditions changes during the process. In addition, it is clear that both die–tube friction conditions and the tube bending effects, which occurs respectively in the tube straight wall and corner zones, are the principal causes of the obtained residual stresses distribution along the tube cross-section.

Experimental Researches upon Changes of a Pipe's Roughness after Hydroformation

2013 ◽  
Vol 371 ◽  
pp. 111-115
Author(s):  
Bogdan Constantin Vaceanu ◽  
Gheorghe Nagit ◽  
Vasile Huian
Keyword(s):  
Surface Roughness ◽  
Tube Hydroforming ◽  
Work Piece ◽  
Copper Pipe ◽  
Work Area ◽  
The Coefficient Of Friction ◽  
Hydroforming Process ◽  
Aluminum Pipe ◽  
Experimental Researches

Surface roughness was studied in the tube hydroforming process, considering the quality of the material and the coefficient of friction between the work piece and die. Other researchers have studied the surface roughness to the front of an aluminum pipe [. The aim of this work was to analyze changes in a copper pipe roughness occurred after hydroforming process with fluid. Effects of changing roughness were studied, following the deformation of the material in the work area and roughness changes occurring in the material flow. After achieving hydroforming process, the surface roughness was measured by electron microscopy SEM in different areas of the hydro formed tube. After hydroforming process, an increase of surface roughness in connection areas of the mold to the curvature and the transverse direction of the pipe.

Corner Fill Modeling of Tube Hydroforming

2000 ◽  
Author(s):  
J. Y. Chen ◽  
Z. C. Xia ◽  
S. C. Tang
Keyword(s):  
Numerical Experiment ◽  
Internal Pressure ◽  
Process Design ◽  
Tube Hydroforming ◽  
Design Guidelines ◽  
Structural Components ◽  
Round Tube ◽  
Fundamental Understanding ◽  
Hydroforming Process ◽  
Square Box

Abstract Hydroforming process provides important advantages for automotive structural components over conventional stamp-and-weld parts, but it also brings unique challenges in process design. This paper attempts to obtain fundamental understanding of the process through corner fill modeling. A round tube is pressurized to expand into a square box with tight radius in the numerical experiment. Several parameters are identified and investigated during the process, namely, the internal pressure, end feed, and the lubricant. Their effects on the deformation profiles are presented, and their importance in process design is discussed. The established design guidelines from the study can be a valuable tool for hydroforming process engineers and part designers.

scholarly journals Movable Die and Loading Path Design in Tube Hydroforming of Irregular Bellows

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1518
Author(s):  
Yeong-Maw Hwang ◽  
Yau-Jiun Tsai
Keyword(s):  
Tube Hydroforming ◽  
Simulation Software ◽  
Die Design ◽  
Loading Path ◽  
Feeding Types ◽  
Element Simulation ◽  
Hydroforming Process ◽  
Formed Product ◽  
Loading Path Design ◽  
Deform 3D

Manufacturing of irregular bellows with small corner radii and sharp angles is a challenge in tube hydroforming processes. Design of movable dies with an appropriate loading path is an alternative solution to obtain products with required geometrical and dimensional specifications. In this paper, a tube hydroforming process using a novel movable die design is developed to decrease the internal pressure and the maximal thinning ratio in the formed product. Two kinds of feeding types are proposed to make the maximal thinning ratio in the formed bellows as small as possible. A finite element simulation software “DEFORM 3D” is used to analyze the plastic deformation of the tube within the die cavity using the proposed movable die design. Forming windows for sound products using different feeding types are also investigated. Finally, tube hydroforming experiments of irregular bellows are conducted and experimental thickness distributions of the products are compared with the simulation results to validate the analytical modeling with the proposed movable die concept.

Sign in / Sign up

Export Citation Format

Share Document