scholarly journals Numerical investigation of plastic flow and residual stresses generated in hydroformed tubes

2021 ◽  
pp. 146442072198974
Author(s):  
A Ktari ◽  
A Abdelkefi ◽  
N Guermazi ◽  
P Malecot ◽  
N Boudeau
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Plastic Flow ◽  
Tube Hydroforming ◽  
Three Dimensional ◽  
Element Model ◽  
Tube Cross Section ◽  
Straight Wall ◽  
Hydroforming Process

During tube hydroforming process, the friction conditions between the tube and the die have a great importance on the material plastic flow and the distribution of residual stresses of the final component. Indeed, a three-dimensional finite element model of a tube hydroforming process in the case of square section die has been performed, using dynamic and static approaches, to study the effect of the friction conditions on both plastic flow and residual stresses induced by the process. First, a comparative study between numerical and experimental results has been carried out to validate the finite element model. After that, various coefficients of friction were considered to study their effect on the thinning phenomenon and the residual stresses distribution. Different points have been retained from this study. The thinning is located in the transition zone cited between the straight wall and the corner zones of hydroformed tube due to the die–tube contact conditions changes during the process. In addition, it is clear that both die–tube friction conditions and the tube bending effects, which occurs respectively in the tube straight wall and corner zones, are the principal causes of the obtained residual stresses distribution along the tube cross-section.

Multipass low-plasticity burnishing induced residual stresses: Three-dimensional elastic-plastic finite element modelling

2004 ◽  
Vol 218 (6) ◽  
pp. 663-668 ◽  
Author(s):  
W Zhuang ◽  
B Wicks
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stress Field ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Residual Stress Field ◽  
Moving Contact ◽  
Low Plasticity Burnishing

Low-plasticity burnishing (LPB) is a surface modification process involving complex cyclic plastic deformation that results in the development of a deep residual stress field. In order to achieve an optimal LPB-induced residual stress field for the geometry appropriate to the aircraft engine component, the key parameters of the LPB process, such as burnishing load, burnishing ball size and material properties, need to be determined. For this purpose, a three-dimensional non-linear moving contact finite element model is proposed to simulate the multipass LPB process and to predict the effects of those parameters on the resultant residual stress field. The material constitutive model used in the finite element analysis has been developed from the cyclic stress/strain response obtained from experimental measurements on the material. Prediction of the LPB-induced residual stresses by the finite element model appears to agree reasonably well with X-ray diffraction measurements.

Experimental and Numerical Analysis of Residual Stresses in Additive Layer Manufacturing by Laser Melting of Metal Powders

2010 ◽  
Vol 450 ◽  
pp. 461-465 ◽  
Author(s):  
Ibiye A. Roberts ◽  
Chang J. Wang ◽  
Mark Stanford ◽  
Kevin A. Kibble ◽  
Diane J. Mynors
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Stress Fields ◽  
Metal Powders ◽  
Additive Layer Manufacturing ◽  
Layer Manufacturing

Determining the three-dimensional residual stress fields and the associated distortions using numerical simulations for multi-layered parts has proved to be a challenge in additive layer manufacturing. This paper presents an innovative three-dimensional thermal-elasto-plastic finite element model for predicting the deformation and residual stress fields in TiAl6V4 parts built on steel platforms. The developed model utilises temperature dependent material physical and mechanical properties as well as latent heat of melting. Experiments conducted using surface profilometry showed good agreement with the simulation results. The finite element model was used to investigate the overall effect of the melting powder on the platform deformation and residual stresses for multiple layers of deposited powder.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Reduction of Free-Edge Stress Concentration

1985 ◽  
Vol 52 (4) ◽  
pp. 801-805 ◽  
Author(s):  
P. R. Heyliger ◽  
J. N. Reddy
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Free Edge ◽  
Shear Stresses ◽  
Normal Stresses ◽  
Interlaminar Shear ◽  
Three Dimensional Elasticity

A quasi-three dimensional elasticity formulation and associated finite element model for the stress analysis of symmetric laminates with free-edge cap reinforcement are described. Numerical results are presented to show the effect of the reinforcement on the reduction of free-edge stresses. It is observed that the interlaminar normal stresses are reduced considerably more than the interlaminar shear stresses due to the free-edge reinforcement.

Sign in / Sign up

Export Citation Format

Share Document