Inertial migration of a circular particle in nonoscillatory and oscillatory pressure-driven flows at moderately high Reynolds numbers

2009 ◽  
Vol 41 (5) ◽  
pp. 055501 ◽  
Author(s):  
Bo Sun ◽  
Zhaosheng Yu ◽  
Xueming Shao
Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 198
Author(s):  
Yanfeng Gao ◽  
Pascale Magaud ◽  
Lucien Baldas ◽  
Yanping Wang

The inertial migration of particles in microchannel flows has been deeply investigated in the last two decades. In spite of numerous reports on the inertial focusing patterns in a square channel, the particle inertial focusing and longitudinal ordering processes remain unclear at high Reynolds numbers (>200) in square microchannels smaller than 100 µm in width. Thus, in this work, in situ visualization of particles flowing in square micro-channels at Reynolds numbers Re ranging from 5 to 280 has been conducted and their migration behaviors have been analyzed. The obtained results confirm that new equilibrium positions appear above a critical Re depending on the particle to channel size ratio and the particle volume fraction. It is also shown that, for a given channel length, an optimal Reynolds number can be identified, for which the ratio of particles located on equilibrium positions is maximal. Moreover, the longitudinal ordering process, i.e., the formation of trains of particles on equilibrium positions and the characterization of their length, has also been analyzed for the different flow conditions investigated in this study.


2012 ◽  
Vol 43 (5) ◽  
pp. 589-613
Author(s):  
Vyacheslav Antonovich Bashkin ◽  
Ivan Vladimirovich Egorov ◽  
Ivan Valeryevich Ezhov ◽  
Sergey Vladimirovich Utyuzhnikov

AIAA Journal ◽  
1999 ◽  
Vol 37 ◽  
pp. 1062-1071 ◽  
Author(s):  
A. Seifert ◽  
L. G. Pack

AIAA Journal ◽  
2000 ◽  
Vol 38 ◽  
pp. 825-834
Author(s):  
F. Novak ◽  
T. Sarpkaya

2004 ◽  
Author(s):  
William L. Keith ◽  
Kimberly M. Cipolla ◽  
David R. Hart ◽  
Deborah A. Furey

Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.


Sign in / Sign up

Export Citation Format

Share Document