scholarly journals Effect of corrugated minichannel variable width on entropy generation for convective heat transfer of alpha-Alumina-water nanofluid

2021 ◽  
Vol 2053 (1) ◽  
pp. 012016
Author(s):  
N M Muhammad ◽  
N A C Sidik ◽  
A Saat ◽  
Y Asako ◽  
W M A A Japar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Entropy Production ◽  
Convective Heat ◽  
Entropy Generation ◽  
Entropy Generation Rate ◽  
Thermal Systems ◽  
Volume Fractions ◽  
Thermal Entropy ◽  
Alpha Alumina

Abstract Energy management and sustainability in thermal systems require maximum utilization of resources with minimal losses. However, it is rarely unattainable due to the ever-increasing need for a high-performance system combined with device size reduction. The numerical study examined convective heat transfer of an alpha-Alumina-water nanofluid in variable-width corrugated minichannel heat sinks. The objective is to study the impact of nanoparticle volume fractions and flow area variation on the entropy generation rate. The determining variables are 0.005 – 0.02 volume fractions, the fluid velocity 3 – 5.5 m/s and heat flux of 85 W/cm2. The numerical results show an acceptable correlation with the experiment results. The results indicate the thermal entropy production drop with an increase in nanoparticles volume fraction. Contrastingly, the frictional resistance entropy suggests the opposite trend due to the turbulence effect on the fluid viscosity. The induction of Alumina-Water nanofluid with enhanced thermal conductivity declined the entropy generation rate compared to water alone. The increase in width ratio by 16% between the cases translates to at least a 9% increase in thermal entropy production. The outcome of this study can provide designers and operators of thermal systems more insight into entropy management in corrugated heatsinks.

Analysis of Entropy Generation During Mixed Convective Heat Transfer of Nanofluids Past a Rotating Circular Cylinder

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Sandip Sarkar ◽  
Suvankar Ganguly ◽  
Amaresh Dalal
Keyword(s):  
Heat Transfer ◽  
Circular Cylinder ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Entropy Generation ◽  
Colloidal Particles ◽  
Volume Fractions ◽  
Rotating Circular Cylinder ◽  
Nanoparticle Agglomeration ◽  
Cylinder Rotation

The entropy generation due to mixed convective heat transfer of nanofluids past a rotating circular cylinder placed in a uniform cross stream is investigated via streamline upwind Petrov–Galerkin based finite element method. Nanosized copper (Cu) particles suspended in water are used with Prandtl number (Pr) = 6.9. The computations are carried out at a representative Reynolds number (Re) of 100. The dimensionless cylinder rotation rate, α, is varied between 0 and 2. The range of nanoparticle volume fractions (ϕ) considered is 0 ≤ ϕ ≤ 5%. Effect of aiding buoyancy is brought about by considering two fixed values of the Richardson number (Ri) as 0.5 and 1.0. A new model for predicting the effective viscosity and thermal conductivity of dilute suspensions of nanoscale colloidal particles is presented. The model addresses the details of the agglomeration–deagglomeration in tune with the pertinent variations in the effective particulate dimensions, volume fractions, as well as the aggregate structure of the particulate system. The total entropy generation is found to decrease sharply with cylinder rotation rates and nanoparticle volume fractions. Increase in nanoparticle agglomeration shows decrease in heat transfer irreversibility. The Bejan number falls sharply with increase in α and ϕ.

Convective Heat Transfer Enhancement in Solar Receivers Using Minimum Entropy Generation Optimization

2011 ◽  
Author(s):  
Qi Li ◽  
Xigang Yuan ◽  
Pierre Neveu ◽  
Gilles Flamant
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Convective Heat ◽  
Entropy Generation ◽  
Minimum Entropy ◽  
Transfer Enhancement ◽  
Optimal Velocity ◽  
Minimum Entropy Generation ◽  
Convective Heat Transfer Enhancement

Convective heat transfer enhancement can significantly improve the thermal efficiency in the conversion, utilization, recovery and storage of energy (in particular solar thermal). Modifying velocity field is the most direct approach to enhance convective heat transfer. However, in most cases the optimal velocity field is unknown and difficult to find even for an experienced researcher. In this paper, a predictive optimization methodology in convective heat transfer enhancement based on minimum entropy generation (MEG) principle was developed. A set of Euler’s equations were derived by the variation calculus to the Lagrange function established by governing equations, specific constraints and objective functional—total entropy generation rate. The solution of these equations resulted in the optimal velocity fields, leading to the minimum entropy generation. To validate and demonstrate the future application of this methodology to solar absorbers used to convert concentrated solar energy, the steady laminar convection heat transfer process in a two-dimensional channel with fixed heat flux boundaries was optimized for given total viscous dissipations. The numerical simulation results showed that lower value of maximum wall temperature was obtained by MEG optimization, which means cheaper and safer materials. The present work indicated that the new methodology could be a good guide in convective heat transfer enhancement design work, especially in CSP receivers.

Entropy generation and second law analysis of pulsed impinging jet

2015 ◽  
Vol 25 (5) ◽  
pp. 1089-1106 ◽  
Author(s):  
Kazem Esmailpour ◽  
Behnam Bozorgmehr ◽  
Seyed Mostafa Hosseinalipour ◽  
Arun S. Mujumdar
Keyword(s):  
Heat Transfer ◽  
Temperature Field ◽  
Entropy Generation ◽  
Impinging Jet ◽  
Entropy Generation Rate ◽  
Second Law ◽  
Pulsation Frequency ◽  
Content Type ◽  
Thermal Entropy ◽  
Plate Distance

Purpose – The purpose of this paper is to examine entropy generation rate in the flow and temperature field due pulsed impinging jet on to a flat plate. Heat transfer of pulsed impinging jets has been investigated by many researchers. Entropy generation is one of the parameters related to the second law of thermodynamics which must be analyzed in processes with heat transfer and fluid flow in order to design efficient systems. Effect of velocity profile parameters and various nozzle to plate distances on viscous and thermal entropy generation are investigated. Design/methodology/approach – In this study, the flow and temperature field of a pulsed turbulent impinging jet are simulated numerically by the finite volume method with appropriate boundary conditions. Then, flow and temperature results are used to calculate the rate of entropy generation due to heat transfer and viscous dissipation. Findings – Results show that maximum viscous and thermal entropy generation occurs in the lowest nozzle to plate distance and entropy generation decreases as the nozzle to plate distance increases. Entropy generation in the two early phase of a period in the most frequencies is more than steady state whereas a completely opposite behavior happens in the two latter phase. Increase in the pulsation frequency and amplitude leads to enhancement in entropy generation because of larger temperature and velocity gradients. This phenomenon appears second and even third peaks in entropy generation plots in higher pulsation frequency and amplitude. Research limitations/implications – The predictions may be extended to include various pulsation signal shape, multiple jet configuration, the radiation effect and phase difference between jets. Practical implications – The results of this paper are a valuable source of information for active control of transport phenomena in impinging jet configurations which is used in different industrial applications such as cooling, heating and drying processes. Originality/value – In this paper the entropy generation of pulsed impinging jet was studied for the first time and a comprehensive discussion on numerical results is provided.

Sign in / Sign up

Export Citation Format

Share Document