Decrease in reflection loss at intermediate adhesive layer for mechanical stacking multi junction solar cells

Author(s):  
Shinya Yoshidomi ◽  
Noritaka Fujii ◽  
Jun Furukawa ◽  
Masahiko Hasumi ◽  
Toshiyuki Sameshima
Robotica ◽  
2005 ◽  
Vol 23 (5) ◽  
pp. 561-565 ◽  
Author(s):  
Zhuang Fu ◽  
Yanzheng Zhao ◽  
Qinghua Yang ◽  
Qixin Cao ◽  
Mingbo Chen ◽  
...  

An auto-bonding robot (ABR) that consists of the mechanism of adhesive dispensing and auto-bonding, a pneumatic system and a control system, is presented in this paper. It is designed for the bonding operation of cover-glasses and space solar cells using adhesives. An adhesive dispensing method is proposed to control the thickness and position of the adhesive layer on solar cells and to provide a satisfactory bonding accuracy. The bubble-free bonding process is realized by the leaning mechanism of a pneumatic sucker. Experimental comparison of the manual and automatic bonding methods showed that there are no fragment and air bubbles between the cover-glass and the space solar cell, and no outflow adhesive on the surface by the automatic bonding process in a non-vacuum condition. The novel automatic bonding robot greatly improved the lightweight space solar cells bonding quality and production rate.


2014 ◽  
Vol 521 ◽  
pp. 52-55
Author(s):  
Chun Rong Xue ◽  
Yu Qin Gu ◽  
Ming Liang Deng

This work presents study of both the antireflection coatings on silicon solar cells and surface texture of silicon solar cell, with the aim to prepare high quality Si solar cells. Surface texturing, either in combination with an anti-reflection coating or by itself, can be used to minimize reflection, but the large reflection loss can be reduced significantly via a suitable anti-reflecting coatings. Significant improvement of the short circuit current after anti-reflecting coatings was observed. It is found that the currentvoltage characteristic with a double-layer anti-reflecting coatings is better than that with a single-layer anti-reflecting coatings. Depositing a multilayer on the textured surface reduces the large reflection loss significantly. The short circuit current of silicon solar cells has significant improvement after depositing anti-reflecting coatings on textured surface silicon, and it increases the efficiency of the Si solar cells.


2008 ◽  
Vol 373-374 ◽  
pp. 774-777 ◽  
Author(s):  
Zhuang Fu ◽  
W.X. Yan ◽  
Y.Z. Zhao

At present, adhesive coating is by far the most widely used technique in the space panel manufacturing. The automatic process level is essential for improving the quality and efficiency of the space solar cell array assembly. In this study, the surface coating model for adhesive dispensing on the space solar cells is obtained, which describes the relationship between the thickness of the adhesive layer on the solar cell, the moving speed of the syringe and the differential pressure. Then the structure of the surface coating robot is presented for the space solar cell arrays assembly. The experimental results have showed that the surface coating robot can greatly improve the efficiency and quality of the space solar cells array assembly. The adhesive no longer outflows and stains the solar cells and the panel. This robot is useful to protect the environment and keep workers away from the poisonous chemicals. Instead of the manual work in space solar cell arrays assembly, the application of the surface coating robot will enhance the development of space industry.


2017 ◽  
Vol 2017 ◽  
pp. 1-6
Author(s):  
Yusi Chen ◽  
Yangsen Kang ◽  
Jieyang Jia ◽  
Yijie Huo ◽  
Muyu Xue ◽  
...  

Nanostructures have been widely used in solar cells due to their extraordinary photon management properties. However, due to poor pn junction quality and high surface recombination velocity, typical nanostructured solar cells are not efficient compared with the traditional commercial solar cells. Here, we demonstrate a new approach to design, simulate, and fabricate whole-wafer nanostructures on dielectric layer on thin c-Si for solar cell light trapping. The optical simulation results show that the periodic nanostructure arrays on dielectric materials could suppress the reflection loss over a wide spectral range. In addition, by applying the nanostructured dielectric layer on 40 μm thin c-Si, the reflection loss is suppressed to below 5% over a wide spectra and angular range. Moreover, a c-Si solar cell with 2.9 μm ultrathin absorber layer demonstrates 32% improvement in short circuit current and 44% relative improvement in energy conversion efficiency. Our results suggest that nanostructured dielectric layer has the potential to significantly improve solar cell performance and avoid typical problems of defects and surface recombination for nanostructured solar cells, thus providing a new pathway towards realizing high-efficiency and low-cost c-Si solar cells.


2018 ◽  
Vol 778 ◽  
pp. 283-289 ◽  
Author(s):  
Asad Ali ◽  
Saddam Ali ◽  
Hassan Ali ◽  
Kamran Alam ◽  
Waqar Ali ◽  
...  

Tandem Solar Cells with Silicon as one of its constituents have flat surfaces (surfaces without texturing). That is why flat surfaces Solar cells have got quite importance. But the issue with the flat surfaces is the high reflection loss (flat) and poor light trapping (no-texturing) in the cells. So, some scattering film, other than direct texturing, that is polydimethylsiloxane (PDMS) polymer with the texture is used. The optimized PDMS film here is the random pyramidal film because random pyramidal PDMS films have a drop of 56.6% in reflectance used on polished Silicon while iso-textured and inverted pyramids have 51.55% and 48.47% respectively. This PDMS film with random textures when applied to 2-terminal monolithic perovskite/Silicon tandem, its external quantum efficiency shows an increase of 1.12mA/cm2in the short-circuit current and reflection loss reduces by 4.1 mA/cm2.


Sign in / Sign up

Export Citation Format

Share Document