Carbon Black/PDMS Based Flexible Capacitive Tactile Sensor for Multi-Directional Force Sensing

Flexible sensing tends to be widely exploited in the process of human–computer interactions of intelligent robots for its contact compliance and environmental adaptability. A novel flexible capacitive tactile sensor was proposed for multi-directional force sensing, which is based on carbon black/polydimethylsiloxane (PDMS) composite dielectric layer and upper and lower electrodes of carbon nanotubes/polydimethylsiloxane (CNTs/PDMS) composite layer. By changing the ratio of carbon black, the dielectric constant of carbon black/PDMS composite layer increases at 4 wt%, and then decreases, which was explained according to the percolation theory of the conductive particles in the polymer matrix. Mathematical model of force and capacitance variance was established, which can be used to predict the value of the applied force. Then, the prototype with carbon black/PDMS composite dielectric layer was fabricated and characterized. SEM observation was conducted and a ratio was introduced in the composites material design. It was concluded that the dielectric constant of carbon sensor can reach 0.1 N within 50 N in normal direction and 0.2 N in 0–10 N in tangential direction with good stability. Finally, the multi-directional force results were obtained. Compared with the individual directional force results, the output capacitance value of multi-directional force was lower, which indicated the amplitude decrease in capacity change in the normal and tangential direction. This might be caused by the deformation distribution in the normal and tangential direction under multi-directional force.

Porous Polydimethylsiloxane Elastomer Hybrid with Zinc Oxide Nanowire for Wearable, Wide-Range, and Low Detection Limit Capacitive Pressure Sensor

We propose a flexible capacitive pressure sensor that utilizes porous polydimethylsiloxane elastomer with zinc oxide nanowire as nanocomposite dielectric layer via a simple porogen-assisted process. With the incorporation of nanowires into the porous elastomer, our capacitive pressure sensor is not only highly responsive to subtle stimuli but vigorously so to gentle touch and verbal stimulation from 0 to 50 kPa. The fabricated zinc oxide nanowire–porous polydimethylsiloxane sensor exhibits superior sensitivity of 0.717 kPa−1, 0.360 kPa−1, and 0.200 kPa−1 at the pressure regimes of 0–50 Pa, 50–1000 Pa, and 1000–3000 Pa, respectively, presenting an approximate enhancement by 21−100 times when compared to that of a flat polydimethylsiloxane device. The nanocomposite dielectric layer also reveals an ultralow detection limit of 1.0 Pa, good stability, and durability after 4000 loading–unloading cycles, making it capable of perception of various human motions, such as finger bending, calligraphy writing, throat vibration, and airflow blowing. A proof-of-concept trial in hydrostatic water pressure sensing has been demonstrated with the proposed sensors, which can detect tiny changes in water pressure and may be helpful for underwater sensing research. This work brings out the efficacy of constructing wearable capacitive pressure sensors based on a porous dielectric hybrid with stress-sensitive nanostructures, providing wide prospective applications in wearable electronics, health monitoring, and smart artificial robotics/prosthetics.

Flexible Capacitive Pressure Sensors with Micro-Patterned Porous Dielectric Layer for Wearable Electronics

Highly sensitive soft sensors play key roles in flexible electronics, which therefore have attracted much attention in recent years. Herein, we report a flexible capacitive pressure sensor with high sensitivity by using engineered micro-patterned porous polydimethylsiloxane (PDMS) dielectric layer through an environmental-friendly fabrication procedure. The porous structure is formed by evaporation of emulsified water droplets during PDMS curing process, while the micro-patterned structure is obtained via molding on sandpaper. Impressively, this structure renders the capacitive sensor with a high sensitivity up to 143.5 MPa-1 at the pressure range of 0.068~150 kPa and excellent anti-fatigue performance over 20,000 cycles. Meanwhile, the sensor can distinguish different motions of the same person or different people doing the same action. Our work illustrates the promising application prospects of this flexible pressure sensor for the security field or human motion monitoring area.

Electrical and Optical Characteristics of SSI-LED Made from Capacitor Containing Tri-Layer WOx Embedded Zr-Doped HfOx Gate Dielectric

Solid-state incandescent light emitting devices made from MOS capacitors with the WOx embedded Zr-doped HfOx gate dielectric were characterized for electrical and optical characteristics. Devices made from capacitors containing Zr-doped HfOx and WOx, gate dielectrics were also fabricated for comparison. The device with the WOx embedded gate dielectric layer had electrical and light emitting characteristics between that with WOx gate dielectric layer and that with the Zr-doped HfOx but no WOx embedded gate dielectric layer. The difference can be explained by the nano-resistor formation process and the content of the high emissivity W in the nano-resistor. The device made from the WOx embedded Zr-doped HfOx gate dielectric MOS capacitor is applicable to areas where uniform emission of warm white light is required.

Flexible Vibrotactile Actuator Based on Dielectric Elastomer for Smart Handheld Devices

This paper presents an electroactive and soft vibrotactile actuator based on a dielectric elastomer. The vibrotactile actuator is composed of an upper layer, an adhesive tape layer, a dielectric layer with bumps, and a lower layer. When a voltage is applied to the actuator, an electrostatic force created between the upper and lower layers pulls the upper layer down, compressing the dielectric layer. As soon as the applied voltage is released, the upper layer is quickly restored to its initial state by the elastic force of the compressed dielectric elastomer. Because two forces contribute to the actuation at the same time, the created vibration is sufficiently strong to stimulate human mechanoreceptors. When the applied voltage is removed, the upper layer and dielectric elastomer return to their initial shapes. We conducted experiments to determine the best weight ratio of polydimethylsiloxane (PDMS) and Ecoflex, and to quantitatively investigate the haptic performance of the proposed vibrotactile actuator. The experiments clearly show that the plasticized vibrotactile actuator can create a variety of haptic sensations over a wide frequency range.

Calculating the Effect of AlGaN Dielectric Layers in a Polarization Tunnel Junction on the Performance of AlGaN-Based Deep-Ultraviolet Light-Emitting Diodes

In this work, AlGaN-based deep-ultraviolet (DUV) light-emitting diodes (LEDs) with AlGaN as the dielectric layers in p+-Al0.55Ga0.45N/AlGaN/n+-Al0.55Ga0.45N polarization tunnel junctions (PTJs) were modeled to promote carrier tunneling, suppress current crowding, avoid optical absorption, and further enhance the performance of LEDs. AlGaN with different Al contents in PTJs were optimized by APSYS software to investigate the effect of a polarization-induced electric field (Ep) on hole tunneling in the PTJ. The results indicated that Al0.7Ga0.3N as a dielectric layer can realize a higher hole concentration and a higher radiative recombination rate in Multiple Quantum Wells (MQWs) than Al0.4Ga0.6N as the dielectric layer. In addition, Al0.7Ga0.3N as the dielectric layer has relatively high resistance, which can increase lateral current spreading and enhance the uniformity of the top emitting light of LEDs. However, the relatively high resistance of Al0.7Ga0.3N as the dielectric layer resulted in an increase in the forward voltage, so much higher biased voltage was required to enhance the hole tunneling efficiency of PTJ. Through the adoption of PTJs with Al0.7Ga0.3N as the dielectric layers, enhanced internal quantum efficiency (IQE) and optical output power will be possible.

A review of modern numerical and analytical models of heat transfer in a dielectric layer during melting due to microwave radiation

In this work, numerical and analytical solutions of heat transfer in a dielectric layer during melting in the microwave field were considered. We considered solutions, where the source term was obtained based on the solution of Maxwell equation, as well as using the Lambert law. The conditions applicable for analytical solutions, allowing the parametric analysis, are determined. The areas of application of the technology of microwave melting of dielectrics, in particular with melting ice on water, defrosting products, etc., were also considered.

Modeling and Simulation of Hafnium Oxide RRAM Based on Oxygen Vacancy Conduction

The resistive memory has become one of the most promising new memory types because of its excellent performance, and HfO2 resistive material has attracted extensive attention. The conduction mechanism based on oxygen vacancy is widely recognized in the research of new nonvolatile memory. An RRAM electrothermal coupling model based on the oxygen vacancy conduction mechanism was constructed using COMSOL. The resistance process of the device is simulated by solving the coefficient partial differential equation, and the distribution of oxygen vacancy concentration, temperature, electric field, electric potential and other parameters in the dielectric layer at different voltages are obtained. The effects of temperature, dielectric layer thickness, top electrode thermal conductivity and conductive wire size on the resistance characteristics of the device are studied. It has guiding significance to further study the RRAM mechanism.