Studying the Thermal and Physical Processes in the Material Surface Layer Under Ultrasonic Plastic Deforming

Author(s):  
Kharis M. Rakhimyanov ◽  
Andrey Kh. Rakhimyanov ◽  
Konstantin Kh. Rakhimyanov
2011 ◽  
Vol 183 ◽  
pp. 143-148 ◽  
Author(s):  
M. Pochrząst ◽  
Jan Marciniak ◽  
K. Wróbel ◽  
Bohdan Bączkowski

The aim of the work was evaluation of electrochemical properties of Co-based alloys (Remanium GM 800+ and Biosil F) and Ni-based alloys (Heraenium NA and Remanium G-Soft) commonly used on frameworks for porcelain faced cast partial dentures. First stage of the work was evaluation of surface roughness by means of direct linear contact measurement (SURTRONIC 3+ profiler, Taylor/Hobson) of samples after casting and surface treatment. Electrochemical properties of surface were assessed by means of potentiodynamic and impedance methods. In potentiodynamic tests, in order to evaluate pitting corrosion resistance of the analyzed alloys, anodic polarization curves were recorded. The VoltaLab® PGP 201 system was applied in corrosion tests. Moreover, in order to evaluate structure and properties of the surface layer the electrochemical impedance spectroscopy (EIS) was applied. Selection of this method enabled to determine the impedance of the material – surface layer – solution interface with the use of approximation of impedance data by means of equivalent electric circuit model. The EIS tests were carried out with the use of the AutoLab PGSTAT 302N system equipped with the FRA2 Faraday impedance module. Electrochemical tests were carried out in artificial saliva at the temperature of 37°C and pH = 7,0±0,1.


2014 ◽  
Author(s):  
Tracy A Villareal ◽  
Cynthia H. Pilskaln ◽  
Joseph P. Montoya ◽  
Mark Dennett

In oceanic gyres, primary producers are numerically dominated by small (1-5 µm diameter) pro- and eukaryotic cells that primarily utilize recycled nutrients produced by rapid grazing turnover in a highly efficient microbial loop. Continuous losses of nitrogen to depth by sinking, either as single cells, aggregates or fecal pellets, are balanced by both nitrate inputs at the base of the euphotic zone and nitrogen-fixation. This input of N (new nitrogen) to balance export losses (the biological pump) is a fundamental aspect of nitrogen cycling and central to understanding carbon fluxes in the ocean. In the Pacific Ocean, detailed nitrogen budgets at the time-series station HOT require upward transport of nitrate from the nutricline (80-100 m) into the surface layer (~0-40 m) to balance productivity and export needs. However, concentration gradients are negligible and cannot support the fluxes. Physical processes can inject nitrate into the base of the euphotic zone, but the mechanisms for transporting this nitrate into the surface layer across many 10s of m in highly stratified systems are unknown. In these seas, vertical migration by the very largest 102-103 µm diameter) phytoplankton is common as a survival strategy to obtain nitrogen from sub-euphotic zone depths. This vertical migration is driven by buoyancy changes rather than by flagellated movement and can provide upward nitrogen transport as nitrate (mM concentrations) in the cells. However, the contribution of vertical migration to nitrate transport has been difficult to quantify over the required basin scales. In this study, we use towed optical systems and isotopic tracers to show that migrating diatom (Rhizosolenia) mats are widespread in the N. Pacific Ocean from 140°W to 175°E and together with other migrating phytoplankton (Ethmodiscus, Halosphaera, Pyrocystis, and solitary Rhizosolenia) can mediate time-averaged transport of N (235 µmol N m-2 d-1) equivalent to eddy nitrate injections (242 µmol NO3- m-2 d-1). This upward biotic transport can close nitrate budgets in the upper 250 m of the central Pacific Ocean and together with diazotrophy creates a surface zone where biological nutrient inputs rather than physical processes dominate the new N flux. In addition to these numerically rare large migrators, there is extensive evidence in the literature of ascending behavior in small phytoplankton that contributes to upward flux as well. Although passive downward movement has dominated models of phytoplankton flux, there is now sufficient evidence to require a rethinking of this paradigm. Quantifying these fluxes is a challenge for the future and requires a reexamination of individual phytoplankton sinking rates as well as methods for capturing and enumerating ascending phytoplankton in the sea.


2014 ◽  
Vol 1059 ◽  
pp. 11-17
Author(s):  
Ivan Kováč ◽  
Rastislav Mikuš ◽  
Jozef Žarnovský ◽  
Juraj Ružbarský

The subject-matter of this article is using diffusion processes to obtain chemically stable compounds with a low reactivity and higher mechanical properties in material surface layer. These processes were implemented by remelting the surface of a given material in arc process using a TIG welding method. Nitrogen was used as an alloying element in experiments. The experiment assumed that the dissociation and ionization of gases, enabling the ionization of diffusion processes in the surface layer of remelted steel, will be achieved by means of electric arc. Conditions for the formation of hard and stable structures with required properties should have been created by enriching the surface layer. The STN 41 5230 steel was used in experiments. After remelting, samples were examined on hardness and relative abrasive wear resistance, which are crucial in terms of required properties of given surface layers. In addition to hardness values in the surface layer, also its behaviour inwards the material up to thermally unaffected base material was determined. When remelting in the environment containing nitrogen, the values of examined quantities increased.


Metals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 140
Author(s):  
Andreas Andris ◽  
Felix Fischer ◽  
Marion Herrmann ◽  
Wolfgang Lippmann ◽  
Antonio Hurtado

Previous studies on the safety of gas-cooled high-temperature reactors (HTR) have analyzed the corrosion and oxidation behavior of the primary circuit components under normal and accident conditions. Through the use of graphite components, graphite particles can be formed by mechanical and chemical means whose influence on the structural change of metal surfaces must be analyzed in a comprehensive manner. The dust resuspension and deposition in tank geometry (DRESDEN-TANK) test facility was set up to thermally anneal metallic samples (Alloy 800H, Inconel 617) loaded with graphite particles under typical HTR conditions (helium, 750 °C, 6 MPa) for the investigation of interactions over a long-term range. In addition to the carrying out of a description of the processes occurring on the material surface, the gaseous reaction products have been analyzed. The results show that the presence of graphite particles in the near-surface layer has a significant impact on corrosion processes due to thermally-induced interactions. In this case iron and chromium are degraded in the metallic alloys, which leads to a structural change in the near-surface layer. Furthermore, the graphite particles significantly influence the formation of the oxide layers on the alloys; for example, they influence the formation speed of the layer and the layer height. The originally deposited particles thus exhibit a chemically-altered composition and a different geometric shape.


Atomic Energy ◽  
2008 ◽  
Vol 104 (6) ◽  
pp. 463-469 ◽  
Author(s):  
A. N. Andrianov ◽  
V. G. Baranov ◽  
G. V. Tikhomirov ◽  
A. V. Khlunov

MAUSAM ◽  
2021 ◽  
Vol 48 (3) ◽  
pp. 375-384
Author(s):  
T.N. JHA ◽  
K. C. SINHA RAY ◽  
H. N. SRIVASTAVA

ABSTRACT. MONI'BLEX-90 data of Varanasi and Jodhpur have been used to study the physical processes in the surface layer. The results show that turbulent transfer of heat, momentum and moisture commence at an average eddy viscosity of an order of magnitude 5.13 × 10-1 J -s kg-1 during rainy day. In absolutely stable case, eddy viscosity may be equal to 4.94 × 10-4 J-s kg-1 or less to decouple surface layer from rest of the planetary boundary layer for extinction of the turbulent transfer of fluxes. These results were based on 8m and 15m meteorological tower observations and surface soil temperature using analytical solution of Byun (1990) and K theory. It was found that the surface layer is decoupled only in case of stability of Class - A because bulk Richardson number is greater than zero and corresponding stability parameter is positive.    


Tribologia ◽  
2020 ◽  
Vol 289 (1) ◽  
pp. 13-19
Author(s):  
Vyacheslav F. BEZJAZYCHNYI ◽  
Marian SZCZEREK ◽  
Roman V. LYUBIMOV

The method, the equipment used, and the results of the study are described in relation to the regularity of changes in the modulus of elasticity of the part material surface layer during operation when the part is under conditions of fretting wear of the contacting surfaces. Recommendations for the practical use of the research results are given.


Atomic Energy ◽  
2008 ◽  
Vol 105 (6) ◽  
pp. 391-396 ◽  
Author(s):  
V. G. Baranov ◽  
M. Yu. Ternovykh ◽  
G. V. Tikhomirov ◽  
A. V. Khlunov

Sign in / Sign up

Export Citation Format

Share Document