Smooth Feedrate Planning and Trajectory Generation for Five-axis Tool Path

2019 ◽  
Author(s):  
Ming-Tsung Lin ◽  
Wei-Xiang Lin ◽  
Yu-Sheng Lin ◽  
Chien-Yi Lee ◽  
Jih-Chieh Lee
Keyword(s):  
Tool Path ◽  
Trajectory Generation ◽  
Feedrate Planning ◽  
Five Axis

Research on Five-Axis Dual-NURBS Adaptive Interpolation Algorithm for Flank Milling

2010 ◽  
Vol 443 ◽  
pp. 330-335 ◽  
Author(s):  
Yu Han Wang ◽  
Jing Chun Feng ◽  
Sun Chao ◽  
Ming Chen
Keyword(s):  
Tool Path ◽  
Flank Milling ◽  
Interpolation Algorithm ◽  
Machining Time ◽  
Surface Machining ◽  
Tool Axis ◽  
Scanning Area ◽  
Nurbs Interpolation ◽  
Milling Method ◽  
Five Axis

In order to exploit the advantages of five-axis flank milling method for space free surface machining to the full, a definition of non-equidistant dual-NURBS tool path is presented first. On this basis, the constraint of velocity of points on the tool axis and the constraint of scanning area of the tool axis are deduced. Considering both of these constraints, an adaptive feed five-axis dual-NURBS interpolation algorithm is proposed. The simulation results show that the feedrate with the proposed algorithm satisfies both of the constraints and the machining time is reduced by 38.3% in comparison with the constant feed interpolator algorithm.

Collision-Free Tool Path Generation for Five-Axis High Speed Machining

2011 ◽  
Vol 474-476 ◽  
pp. 961-966 ◽  
Author(s):  
Li Qiang Zhang ◽  
Min Yue
Keyword(s):  
Image Analysis ◽  
Collision Detection ◽  
High Speed ◽  
Tool Path ◽  
Geometric Model ◽  
High Speed Machining ◽  
Analysis Method ◽  
Geometric Information ◽  
Detection Approach ◽  
Five Axis

Collision detection is a critical problem in five-axis high speed machining. Using a combination of process simulation and collision detection based on image analysis, a rapid detection approach is developed. The geometric model provides the cut geometry for the collision detection and records a dynamic geometric information for in-process workpiece. For the precise collision detection, a strategy of image analysis method is developed in order to make the approach efficient and maintian a high detection precision. An example of five-axis machining propeller is studied to demonstrate the proposed approach. It has shown that the collision detection task can be achieved with a near real-time performance.

Global optimization of tool path for five-axis flank milling with a conical cutter

2010 ◽  
Vol 42 (10) ◽  
pp. 903-910 ◽  
Author(s):  
LiMin Zhu ◽  
Gang Zheng ◽  
Han Ding ◽  
YouLun Xiong
Keyword(s):  
Global Optimization ◽  
Tool Path ◽  
Flank Milling ◽  
Five Axis

scholarly journals Optimisation of Planning Parameters for Machining Blade Electrode Micro-Fillet with Scallop Height Modelling

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 237
Author(s):  
Yue Liu ◽  
Zhanqiang Liu ◽  
Wentong Cai ◽  
Yukui Cai ◽  
Bing Wang ◽  
...  
Keyword(s):  
Path Planning ◽  
Tilt Angle ◽  
Tool Path ◽  
End Milling ◽  
Tool Path Planning ◽  
Scallop Height ◽  
Aero Engine ◽  
Tool Tilt Angle ◽  
Five Axis ◽  
Height Model

Aero-engine blades are manufactured by electroforming process with electrodes. The blade electrode is usually machined with five-axis micromilling to get required profile roughness. Tool path planning parameters, such as cutting step and tool tilt angle, have a significant effect on the profile roughness of the micro-fillet of blade electrode. In this paper, the scallop height model of blade electrode micro-fillet processed by ball-end milling cutter was proposed. Effects of cutting step and tool tilt angle the machined micro-fillet profile roughness were predicted with the proposed scallop height model. The cutting step and tool tilt angle were then optimised to ensure the contour precision of the micro-fillet shape requirement. Finally, the tool path planning was generated and the machining strategy was validated through milling experiments. It was also found that the profile roughness was deteriorated due to size effect when the cutting step decreased to a certain value.

Tool Path Generation for Five-Axis Controlled Machining of Free-Form Surface Using Barrel Tool: Control of Contact Point on Cutting Edge

2020 ◽  
Author(s):  
Tomonobu Suzuki ◽  
Koichi Morishige
Keyword(s):  
Tool Path ◽  
Contact Point ◽  
Cutting Edge ◽  
Free Form ◽  
End Mill ◽  
Ball End Mill ◽  
Surface Machining ◽  
Free Form Surface ◽  
The Cost ◽  
Five Axis

Abstract This study aimed to improve the efficiency of free-form surface machining by using a five-axis controlled machine tool and a barrel tool. The barrel tool has cutting edges, with curvature smaller than the radius, increasing the pick feed width compared with a conventional ball end mill of the same tool radius. As a result, the machining efficiency can be improved; however, the cost of the barrel tool is high and difficult to reground. In this study, a method to obtain the cutting points that make the cusp height below the target value is proposed. Moreover, a method to improve the tool life by continuously and uniformly changing the contact point on the cutting edge is proposed. The usefulness of the developed method is confirmed through machining simulations.

Tool Path Planning for Five-Axis U-Pass Milling of an Impeller

2021 ◽  
Author(s):  
J.Y. Feng ◽  
Z.C. Wei ◽  
M.J. Wang ◽  
X.Q. Wang ◽  
M.L. Guo
Keyword(s):  
Path Planning ◽  
Cutting Force ◽  
Tool Path ◽  
Flank Milling ◽  
Small Range ◽  
Tool Path Planning ◽  
Point Distribution ◽  
Parameter Domain ◽  
Five Axis ◽  
Tool Axis Vector

Abstract U-pass milling is a roughing method that combines the characteristics of flank milling with conventional trochoidal milling. The tool cuts in and out steadily, and the tool–workpiece wrap angle is maintained within a small range. This method can smooth the cutting force and reduce the peak cutting force while avoiding cutting heat accumulation, which can significantly improve the processing efficiency and reduce tool wear. In this study, a tool path model is established for U-pass milling, and the characteristic parameters of the path are defined. Through a comparative test of three-axis groove milling, it is demonstrated that the peak value and average value of the cutting force are reduced by 25% and 60%, respectively. An impeller runner is considered as the processing object, and the milling boundary parameters are pretreated. A tiling micro-arc mapping algorithm is proposed, which maps the three-dimensional boundary to the two-dimensional parameter domain plane with the arc length as the coordinate axis, and the dimensionally reduced tool contact point distribution form is obtained. The geometric domain tool position point and the interference-free tool axis vector are obtained by calculating the bidirectional proportional domain of the runner and the inverse mapping of any vector in the parameter domain. Finally, the calculation results are nested into the automatically programmed tool (APT) encoding form, and the feasibility of the five-axis U-pass milling tool path planning method is verified through a numerical example.

Sign in / Sign up

Export Citation Format

Share Document