A K-Band High-Gain Down-Conversion Mixer in 0.18 $\mu$m CMOS Technology

2009 ◽  
Vol 19 (4) ◽  
pp. 227-229 ◽  
Author(s):  
Dukju Ahn ◽  
Dong-Wook Kim ◽  
Songcheol Hong
Keyword(s):  
Cmos Technology ◽  
High Gain ◽  
Down Conversion ◽  
K Band

A Low-Power, High-Gain, and Low-Noise 802.11a Down-Conversion Mixer in 0.35-μm SiGe Bi-CMOS Technology

2017 ◽  
Vol 26 (09) ◽  
pp. 1750134 ◽  
Author(s):  
Jun-Da Chen ◽  
Song-Hao Wang
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Conversion Gain ◽  
Dc Power ◽  
Down Conversion

The paper presents a novel 5.15[Formula: see text]GHz–5.825[Formula: see text]GHz SiGe Bi-CMOS down-conversion mixer for WLAN 802.11a receiver. The architecture used is based on Gilbert cell mixer, the combination of MOS transistors and HBT BJT transistor device characteristics. The hetero-junction bipolar transistor (HBT) topology is adopted at the transconductance stage to improve power gain and reduce noise factor, and the LO series-parallel CMOS switch topology will be applied to reduce supply voltage and dc power at the switching stage. This mixer is implemented in TSMC 0.35-[Formula: see text]m SiGe Bi-CMOS process, and the chip size including the test pads is 1.175*0.843[Formula: see text]mm2. The main advantages for the proposed mixer are high conversion gain, a moderate linearity, low noise figure, and low power. The post-simulation results achieved are as follows: 14[Formula: see text]dB power conversion gain, [Formula: see text]6[Formula: see text]dBm input third-order intercept point (IIP3), 6.85[Formula: see text]dB double side band (DSB) noise figure. The total mixer current is about 1.54[Formula: see text]mA from 1.4[Formula: see text]V supply voltage including output buffer. The total dc power consumption is 2.15[Formula: see text]mW.

scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

Sign in / Sign up

Export Citation Format

Share Document