scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

scholarly journals Design of a very low-power, low-cost 60 GHz receiver front-end implemented in 65 nm CMOS technology

2011 ◽  
Vol 3 (2) ◽  
pp. 131-138 ◽  
Author(s):  
Michael Kraemer ◽  
Daniela Dragomirescu ◽  
Robert Plana
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Noise Figure ◽  
Low Cost ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Voltage Controlled Oscillator ◽  
60 Ghz ◽  
Front End

The research on the design of receiver front-ends for very high data-rate communication in the 60 GHz band in nanoscale Complementary Metal Oxide Semiconductor (CMOS) technologies is going on for some time now. Although a multitude of 60 GHz front-ends have been published in recent years, they are not consequently optimized for low power consumption. Thus, these front-ends dissipate too much power for battery-powered applications like handheld devices, mobile phones, and wireless sensor networks. This article describes the design of a direct conversion receiver front-end that addresses the issue of power consumption, while at the same time permitting low cost (due to area minimization by the use of spiral inductors). It is implemented in a 65 nm CMOS technology. The realized front-end achieves a record power consumption of only 43 mW including low-noise amplifier (LNA), mixer, a voltage controlled oscillator (VCO), a local oscillator (LO) buffer, and a baseband buffer (without this latter buffer the power consumption is even lower, only 29 mW). Its pad-limited size is 0.55 × 1 mm2. At the same time, the front-end achieves state-of-the-art performance with respect to its other properties: Its maximum measured power conversion gain is 30 dB, the RF and IF bandwidths are 56.5–61.5 and 0–1.5 GHz, respectively, its measured minimum noise figure is 9.2 dB, and its measured IP−1 dB is −36 dBm.

A low power, low noise figure quadrature demodulator for a 60 GHz receiver in 65-nm CMOS technology

2015 ◽  
Vol 36 (4) ◽  
pp. 045005 ◽  
Author(s):  
Najam Muhammad Amin ◽  
Zhigong Wang ◽  
Zhiqun Li ◽  
Qin Li ◽  
Yang Liu
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
60 Ghz

A Low-Power, High-Gain, and Low-Noise 802.11a Down-Conversion Mixer in 0.35-μm SiGe Bi-CMOS Technology

2017 ◽  
Vol 26 (09) ◽  
pp. 1750134 ◽  
Author(s):  
Jun-Da Chen ◽  
Song-Hao Wang
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Conversion Gain ◽  
Dc Power ◽  
Down Conversion

The paper presents a novel 5.15[Formula: see text]GHz–5.825[Formula: see text]GHz SiGe Bi-CMOS down-conversion mixer for WLAN 802.11a receiver. The architecture used is based on Gilbert cell mixer, the combination of MOS transistors and HBT BJT transistor device characteristics. The hetero-junction bipolar transistor (HBT) topology is adopted at the transconductance stage to improve power gain and reduce noise factor, and the LO series-parallel CMOS switch topology will be applied to reduce supply voltage and dc power at the switching stage. This mixer is implemented in TSMC 0.35-[Formula: see text]m SiGe Bi-CMOS process, and the chip size including the test pads is 1.175*0.843[Formula: see text]mm2. The main advantages for the proposed mixer are high conversion gain, a moderate linearity, low noise figure, and low power. The post-simulation results achieved are as follows: 14[Formula: see text]dB power conversion gain, [Formula: see text]6[Formula: see text]dBm input third-order intercept point (IIP3), 6.85[Formula: see text]dB double side band (DSB) noise figure. The total mixer current is about 1.54[Formula: see text]mA from 1.4[Formula: see text]V supply voltage including output buffer. The total dc power consumption is 2.15[Formula: see text]mW.

60 GHz-Band Low-Noise Amplifier

2017 ◽  
Vol 26 (05) ◽  
pp. 1750075 ◽  
Author(s):  
Najam Muhammad Amin ◽  
Lianfeng Shen ◽  
Zhi-Gong Wang ◽  
Muhammad Ovais Akhter ◽  
Muhammad Tariq Afridi
Keyword(s):  
Transmission Line ◽  
Quality Factor ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Constant Current ◽  
60 Ghz ◽  
Frequency Range ◽  
Constant Current Density ◽  
Chip Area

This paper presents the design of a 60[Formula: see text]GHz-band LNA intended for the 63.72–65.88[Formula: see text]GHz frequency range (channel-4 of the 60[Formula: see text]GHz band). The LNA is designed in a 65-nm CMOS technology and the design methodology is based on a constant-current-density biasing scheme. Prior to designing the LNA, a detailed investigation into the transistor and passives performances at millimeter-wave (MMW) frequencies is carried out. It is shown that biasing the transistors for an optimum noise figure performance does not degrade their power gain significantly. Furthermore, three potential inductive transmission line candidates, based on coplanar waveguide (CPW) and microstrip line (MSL) structures, have been considered to realize the MMW interconnects. Electromagnetic (EM) simulations have been performed to design and compare the performances of these inductive lines. It is shown that the inductive quality factor of a CPW-based inductive transmission line ([Formula: see text] is more than 3.4 times higher than its MSL counterpart @ 65[Formula: see text]GHz. A CPW structure, with an optimized ground-equalizing metal strip density to achieve the highest inductive quality factor, is therefore a preferred choice for the design of MMW interconnects, compared to an MSL. The LNA achieves a measured forward gain of [Formula: see text][Formula: see text]dB with good input and output impedance matching of better than [Formula: see text][Formula: see text]dB in the desired frequency range. Covering a chip area of 1256[Formula: see text][Formula: see text]m[Formula: see text]m including the pads, the LNA dissipates a power of only 16.2[Formula: see text]mW.

scholarly journals Design of Low Power UWB CMOS Low Noise Amplifier using Active Inductor for WLAN Receiver

2018 ◽  
Vol 7 (2.24) ◽  
pp. 448
Author(s):  
S Manjula ◽  
M Malleshwari ◽  
M Suganthy
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Wide Band ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Design System ◽  
Active Inductor ◽  
Chip Area ◽  
Noise Amplifier

This paper presents a low power Low Noise Amplifier (LNA) using 0.18µm CMOS technology for ultra wide band (UWB) applications. gm boosting common gate (CG) LNA is designed to improve the noise performance.  For the reduction of on chip area, active inductor is employed at the input side of the designed LNA for input impedance matching. The proposed UWB LNA is designed using Advanced Design System (ADS) at UWB frequency of 3.1-10.6 GHz. Simulation results show that the gain of 10.74+ 0.01 dB, noise figure is 4.855 dB, input return loss <-13 dB and 12.5 mW power consumption.  

Inductive Feedback Technique for Design of High Gain 0.18μm CMOS LNA for 5G Applications

2021 ◽  
pp. 2150236
Author(s):  
Anjana Jyothi Banu ◽  
G. Kavya ◽  
D. Jahnavi
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Common Source ◽  
Matching Network ◽  
Input Matching ◽  
Cmos Lna ◽  
Noise Amplifier

A 26[Formula: see text]GHz low-noise amplifier (LNA) designed for 5G applications using 0.18[Formula: see text][Formula: see text]m CMOS technology is proposed in this paper. The circuit includes a common-source in the first stage to suppress the noise in the amplifier. The successive stage has a Cascode topology along with an inductive feedback to improve the power gain. The input matching network is designed to achieve the input reflection coefficient less than [Formula: see text]7dB at the intended frequency. The matching network at the output is designed using inductor–capacitor (LC) components connected in parallel to attain the output reflection coefficient of [Formula: see text]10[Formula: see text]dB. Due to the inductor added in feedback at the second stage. The [Formula: see text] obtained is 18.208[Formula: see text]dB at 26[Formula: see text]GHz with a noise figure (NF) of 2.8[Formula: see text]dB. The power supply given to the LNA is 1.8[Formula: see text]V. The simulation and layout of the presented circuit are performed using Cadence Virtuoso software.

Design Analysis of Inductorless Active Loaded Low Power UWB LNA Using Noise Cancellation Technique

Frequenz ◽  
2020 ◽  
Vol 74 (3-4) ◽  
pp. 137-144 ◽  
Author(s):  
Dheeraj Kalra ◽  
Manish Kumar ◽  
Aasheesh Shukla ◽  
Laxman Singh ◽  
Zainul Abdin Jaffery
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Broad Band ◽  
Wide Band ◽  
Cmos Technology ◽  
Noise Cancellation ◽  
Low Noise ◽  
Design Analysis ◽  
Common Source ◽  
Power Gain

AbstractThis paper includes a design analysis of an inductorless low-power (LP) low-noise amplifier (LNA) with active load for Ultra Wide Band (UWB) applications. The proposed LNA consists of two parallel paths, one is the common source (CS) path and second is the CG path. The CG path has the edge advantage of improving overall Noise figure (NF) due to wide band impedance matching in UWB, while the CS path provides high power gain. A method for noise cancellation is adopted, to reduce the noise of CS path with the help of CG path. The proposed LNA successfully simulated in 90 nm CMOS technology. The results of proposed work indicate optimization at frequency 5.70 GHz with 3 dB bandwidth of 4.3 GHz–8.9 GHz. All simulations have been done for a range of frequency 03 GHz–13 GHz in Cadence virtuoso software. The results quoted 1.15 dB NF, −18.12 dB S11, 13.7 dB S21, maximum operating power gain (GP) 11.756 dB at frequency 5.7 GHz and available power gain (GA) is 10.17 dB at frequency 8.61 GHz, with 0.6 V, 0.92 mW broad band LNA.

Sign in / Sign up

Export Citation Format

Share Document