The effect of proton and gamma radiation on different types of temperature sensors

Author(s):  
Miguel Gonzalez-Guerrero ◽  
Maria T. Alvarez ◽  
Juan J. Jimenez ◽  
Jaime Sanchez-Paramo ◽  
Hector Guerrero
2004 ◽  
Vol 51 (5) ◽  
pp. 2293-2297 ◽  
Author(s):  
P.M. Mockett ◽  
R.M. Smith ◽  
M.S. Twomey

2014 ◽  
Vol 30 ◽  
pp. 1-10
Author(s):  
J.D. Barshile

Present investigation was undertaken to study the frequency and spectrum of induced viable macromutations employing SA, EMS and gamma radiation in chickpea (Cicer arietinum L.) cultivar Vishwas (Phule G 5). The seeds of chickpea, cultivar Vishwas were treated with three different concentrations / doses of SA (2, 3 and 4 mM), EMS (8, 12 and 16 mM) and gamma radiations (400, 500 and 600 Gy). The mutagen administered seeds were sown in experimental fields to raise M1 progeny. Seeds of M1 plants and control were harvested separately and sown to raise M2 population. The M2 progeny were screened for viable macromutaions. A wide spectrum of viable macromutations was isolated in the M2 generation. In all twenty four different types of viable morphological macromutations were observed. These included 7 types of plant type mutations and 6 types of leaf mutations, 1 types of flower mutation, 5 types of pod mutation and 5 types of seed mutations. Results indicated that all mutagenic treatments were effective in inducing viable mutations in chickpea, during M2 generation. Differences in response to different mutagens were observed in the spectrum and frequency of viable mutations. Some mutation types occurred more frequently than others. The frequency and spectrum of viable mutations were relatively high with EMS followed by gamma radiation and SA. In the present investigation, an attempt has been made for increasing frequency and spectrum of locally important chickpea cultivar ‘Vishwas’ employing chemical and physical mutagens.


2015 ◽  
Vol 660 ◽  
pp. 192-197
Author(s):  
Iosif Boros ◽  
Cristina Tanasa ◽  
Valeriu Stoian ◽  
Daniel Dan

This paper presents the design and monitoring scheme of an energy efficient high school building with emphasis on the analysis of constructive and geometric thermal bridges that can affect the overall energy consumption and thermal comfort. The ANTHERM software is used to accurately assess the specific details and determine isotherms, heat flux distribution and the Psi-values (Ψ value) of the sections where different types of materials connect. A monitoring system with temperature sensors installed in the layers of the building envelope elements has been designed in order to compare the obtained values with the real time thermal performances of the envelope elements. The study highlights the influence of the type and thickness of the insulation materials used in the specific constructive details on the overall thermal performance of buildings.


2018 ◽  
Vol 4 (2) ◽  
pp. 120
Author(s):  
Andi Rosman N.

The design of iron (Fe) and Copper (Cu) thermocouples has been carried out for temperature sensors. The sensor will be made of two different types of materials namely iron and copper. The reference temperature used is 10C. The data collection procedure is first of all a thermocouple with a hot junction is tied together with a solder as a heat source. Besides that, it is also tied to a factory thermocouple that functions as a calibrator. Then the other end of the thermocouple (cold junction) will be inserted into a container containing ice cubes. Then the ports for each thermocouple will be connected to a multimeter, each of which is used to measure temperature (0C) and voltage (mV). From the results of observations and analyzes, it was found that for iron and copper thermocouples had the following characteristics: Seebeck coefficient was 0.001, the mean temperature rises and falls respectively (106.17 ± 0.82) 0C and (118.67 ± 0.90) 0C. The sensitivity of the thermocouple is 0.5 mV / 0C with linearity of 0.9.


Sign in / Sign up

Export Citation Format

Share Document