Judgments of Personal and Environmental Risks of Consumer Products-Do they Differ?

Risk Analysis ◽  
1998 ◽  
Vol 18 (1) ◽  
pp. 119-129 ◽  
Author(s):  
Holger Schutz ◽  
Peter M. Wiedemann
Author(s):  
K. Thomas ◽  
N. Monteiro-Riviere ◽  
D. Warheit ◽  
N. Savage

This article discusses the risks associated with nanomaterials. The use of nanomaterials in consumer products and industrial applications is becoming more prevalent owing to their range of benefits. Nanomaterials have found uses in energy production, home appliances, water treatment, novel therapeutic delivery techniques and dietary supplements, consumer electronics, and sports equipment. While considerable attention has been given to the likely commercial advantages associated with nanomaterials, less emphasis has been placed on the development of a systematic approach for characterizing the human health and environmental risks from exposure to nanomaterials. This article first considers the use of nanomaterials in consumer products and the characterization of nanomaterials before describing a systematic evaluation of the hazards associated with nanomaterials. It also examines pulmonary exposure assessment and dermal exposure assessment, along with risk assessment for exposure to nanomaterials. Finally, it outlines research priorities for the development of more refined estimates of nanomaterial risk.


2021 ◽  
Author(s):  
Chong Han ◽  
Hongxing Yang ◽  
Kun Li ◽  
Patrick Lee ◽  
John Liggio ◽  
...  

Abstract. Cyclic volatile methyl siloxanes (cVMS) are active ingredients in widely used consumer products, which can volatilize into the atmosphere, thus attracting much attention due to their potential environmental risks. While in the atmosphere the cVMS undergo oxidation yielding both gaseous and particulate products. The aerosol yields and compositions from the OH oxidation of four cVMS (D3-D6) were determined under low and high-NOx conditions in an oxidation flow reactor. The aerosol yields progressively increased from D3 to D6, consistent with the volatilities and molecule weights of these cVMS. NOx can restrict the formation of SOA, leading to lower SOA yields under high-NOx conditions than under low-NOx conditions, with a yield decrease between 0.05–0.30 depending on the cVMS. Ammonium sulfate seeds exhibited minor impacts on SOA yields under low-NOx conditions, but significantly increased the SOA yields in the oxidation of D3-D5 at short photochemical ages under high-NOx conditions. The mass spectra of the SOA showed a dependence of its chemical compositions on OH exposure. At high exposures, equivalent to photochemical ages of > 6 days in the atmosphere, D4-D6 SOA mainly consisted of CxHy and CxHyOzSin under low-NOx conditions, whereas they primarily contained NmOz, CxHy, CxHyO1, CxHyO>1 and CxHyOzSin under high-NOx conditions. Using the yield data from the present study and reported cVMS annual production, a global cVMS-derived SOA source strength is estimated to be 0.16 Tg yr−1, distributed over major urban centers.


Author(s):  
Delma P. Thomas ◽  
Dianne E. Godar

Ultraviolet radiation (UVR) from all three waveband regions of the UV spectrum, UVA (320-400 nm), UVB (290-320 nm), and UVC (200-290 nm), can be emitted by some medical devices and consumer products. Sunlamps can expose the blood to a considerable amount of UVR, particularly UVA and/or UVB. The percent transmission of each waveband through the epidermis to the dermis, which contains blood, increases in the order of increasing wavelength: UVC (10%) < UVB (20%) < UVA (30%). To investigate the effects of UVR on white blood cells, we chose transmission electron microscopy to examine the ultrastructure changes in L5178Y-R murine lymphoma cells.


2003 ◽  
Author(s):  
Raymond W. Lim ◽  
Michael S. Wogalter
Keyword(s):  

TAPPI Journal ◽  
2018 ◽  
Vol 17 (01) ◽  
pp. 31-37
Author(s):  
Bryan McCulloch ◽  
John Roper ◽  
Kaitlin Rosen

Barrier coatings are used in applications including food packaging, dry goods, and consumer products to prevent transport of different compounds either through or into paper and paperboard substrates. These coatings are useful in packaging to contain active ingredients, such as fragrances, or to protect contents from detrimental substances, such as oxygen, water, grease, or other chemicals of concern. They also are used to prevent visual changes or mechanical degradation that might occur if the paper becomes saturated. The performance and underlying mechanism depends on the barrier coating type and, in particular, on whether the barrier coating is designed to prevent diffusive or capillary transport. Estimates on the basis of fundamental transport phenomena and data from a broad screening of different barrier materials can be used to understand the limits of various approaches to construct barrier coatings. These estimates also can be used to create basic design rules for general classes of barrier coatings.


Sign in / Sign up

Export Citation Format

Share Document