CFD SIMULATION OF A PLATE HEAT EXCHANGER WITH TRAPEZOIDAL CHEVRON

2016 ◽  
Vol 78 (8-4) ◽  
Author(s):  
Chin Yung Shin ◽  
Normah Mohd-Ghazali
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Friction Factor ◽  
Cfd Simulation ◽  
General Pattern ◽  
Plate Heat Exchanger ◽  
Plate Heat ◽  
Flow Configuration ◽  
Heat Transfer Capacity

In this research, the trapezoidal shaped chevron plate heat exchanger (PHE) is simulated using computational fluid dynamics (CFD) software to determine its heat transfer capacity and friction factor. The PHE is modelled with chevron angles from 30° to 60°, and also the performances are compared with the plain PHE. The validation is done by comparing simulation result with published references using 30° trapezoidal chevron PHE. The Nusselt number and friction factor obtained from simulation model is plotted against different chevron angles. The Nusselt number and friction factor is also compared with available references, which some of the references used sinusoidal chevron PHE. The general pattern of Nusselt number and friction factor with increasing chevron angle agrees with the references. The heat transfer capacity found in current study is higher than the references used, and at the same time, the friction factor also increased. Besides this, it is also found that the counter flow configuration has better heat transfer capacity performance than the parallel flow configuration.

scholarly journals CFD SIMULATION OF THE HEAT TRANSFER PROCESS IN A CHEVRON PLATE HEAT EXCHANGER USING THE SST TURBULENCE MODEL

2015 ◽  
Vol 55 (4) ◽  
pp. 267 ◽  
Author(s):  
Jan Skočilas ◽  
Ievgen Palaziuk
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Transfer Process ◽  
Cfd Simulation ◽  
Numerical Study ◽  
Analytical Calculation ◽  
Heat Transfer Process ◽  
Plate Heat Exchanger ◽  
Hot Water ◽  
Plate Heat

<p>This paper deals with a computational fluid dynamics (CFD) simulation of the heat transfer process during turbulent hot water flow between two chevron plates in a plate heat exchanger. A three-dimensional model with the simplified geometry of two cross-corrugated channels provided by chevron plates, taking into account the inlet and outlet ports, has been designed for the numerical study. The numerical model was based on the shear-stress transport (SST) <em>k-!</em> model. The basic characteristics of the heat exchanger, as values of heat transfer coefficient and pressure drop, have been investigated. A comparative analysis of analytical calculation results, based on experimental data obtained from literature, and of the results obtained by numerical simulation, has been carried out. The coefficients and the exponents in the design equations for the considered plates have been arranged by using simulation results. The influence on the main flow parameters of the corrugation inclination angle relative to the flow direction has been taken into account. An analysis of the temperature distribution across the plates has been carried out, and it has shown the presence of zones with higher heat losses and low fluid flow intensity.</p>

scholarly journals Experimental and numerical studies of a spiral plate heat exchanger

2014 ◽  
Vol 18 (4) ◽  
pp. 1355-1360 ◽  
Author(s):  
Rajavel Rangasamy
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Numerical Study ◽  
Numerical Models ◽  
Plate Heat Exchanger ◽  
Test Fluid ◽  
Plate Heat ◽  
Plate Spacing ◽  
Spiral Plate

An experimental and numerical study of heat transfer and flow characteristics of spiral plate heat exchanger was carried out. The effects of geometrical aspects of the spiral plate heat exchanger and fluid properties on the heat transfer characteristics were also studied. Three spiral plate heat exchangers with different plate spacing (4mm, 5mm and 6 mm) were designed, fabricated and tested. Physical models have been experimented for different process fluids and flow conditions. Water is taken as test fluid. The effect of mass flow rate and Reynolds number on heat transfer coefficient has been studied. Correlation has been developed to predict Nusselt numbers. Numerical models have been simulated using CFD software package FLUENT 6.3.26. The numerical Nusselt number have been calculated and compared with that of experimental Nusselt number.

scholarly journals Characteristics of heat transfer and pressure drop in a chevron-type plate heat exchanger with Al2O3/water nanofluids

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2379-2391 ◽  
Author(s):  
Murat Unverdi ◽  
Yasar Islamoglu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Volume Concentration ◽  
Plate Heat Exchanger ◽  
Distilled Water ◽  
Maximum Volume ◽  
Plate Heat

In this study, heat transfer and pressure drop characteristics have been experimentally investigated by using Al2O3-water nanofluids in the chevron-type plate heat exchanger. The purpose of the experiments was to determine the heat transfer coefficient and pressure drop for different flow rates of 90, 120, 150, 180, 240, and 300 kg/h and different volume concentrations of 0.25%, 0.5%, 0.75%, and 1% of the nanofluids. The Nusselt number of the nanofluids increased with the increasing volume concentration and flow rate at constant hot water flow rate and constant inlet temperatures. The increase in the Nusselt number is 42.4% when compared to distilled water at the maximum volume concentration and Reynolds number (600 ? Re ? 1900) in the nanofluids-plate heat exchanger. It has been concluded that nanofluids enhanced the heat transfer significantly and pressure drops at the maximum volume concentration and the Reynolds number increased by between 6.4% and 8.4% compared to distilled water.

Sign in / Sign up

Export Citation Format

Share Document