The Role of Fin Geometry in Heat Sink Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 324-330 ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Generation Rate ◽  
Heat Transfer Fluid ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Axis Ratio

The following study will examine the effect on overall thermal/fluid performance associated with different fin geometries, including, rectangular plate fins as well as square, circular, and elliptical pin fins. The use of entropy generation minimization, EGM, allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including base plate and applying the conservations equations for mass and energy with the entropy balance. The formulation for the dimensionless entropy generation rate is developed in terms of dimensionless variables, including the aspect ratio, Reynolds number, Nusselt number, and the drag coefficient. Selected fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and Reynolds number. The results clearly indicate that the preferred fin profile is very dependent on these parameters.

The Role of Fin Geometry in Heat Sink Performance

2003 ◽  
Author(s):  
Waqar A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Rectangular Plates ◽  
Minimum Entropy ◽  
Axis Ratio ◽  
Pin Fins ◽  
Minimum Entropy Generation

The following study will examine the effect on overall thermal/fluid performance associated with different fin geometries, including, rectangular plates as well as square, circular and elliptical pin fins. The use of EGM allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general expression for the entropy generation rate is obtained by using the conservations equations for mass, energy, and entropy. The formulation for the dimensionless entropy generation rate is developed in terms of dimensionless variables, including the aspect ratio, Reynolds number, Nusselt number and the drag coefficient. Selected fin geometries are examined for the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and approach velocity. The results clearly indicate that the preferred fin profile is very dependent on these parameters.

scholarly journals Effect of Using Extra Fins on the Pin Fin Classic Geometry for Enhancement Heat Sink Performance using EGM Method

2018 ◽  
Vol 24 (4) ◽  
pp. 1 ◽  
Author(s):  
Kadhum Audaa Jehhef
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Cross Section ◽  
Entropy Generation ◽  
Heat Sink ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Pin Fin ◽  
Pin Fins

In the present study, the effect of new cross-section fin geometries on overall thermal/fluid performance had been investigated. The cross-section included the base original geometry of (triangular, square, circular, and elliptical pin fins) by adding exterior extra fins along the sides of the origin fins. The present extra fins include rectangular extra fin of 2 mm (height) and 4 mm (width) and triangular extra fin of 2 mm (base) 4 mm (height). The use of entropy generation minimization method (EGM) allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including a base plate and applying the conservations equations of mass and energy with the entropy balance. The dimensionless numbers used includes the aspect ratio (ε), Reynolds number (Re), Nusselt number (Nu), and the drag coefficients (CD). Fourteen different cross-section fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate. The results showed that the Nusselt number increases with increasing the Reynolds number for all employed models. The ellipse models (ET and ER-models) give the highest value in the Nusselt number as compared with the classical pin fins. The fin of the square geometry with four rectangular extra fins (SR-models) gives an agreement in Nusselt number as compared with the previous study.  

scholarly journals Effects of gaseous slip flow and temperature jump on entropy generation rate in rectangular microducts

2020 ◽  
Vol 24 (5 Part A) ◽  
pp. 3001-3011
Author(s):  
Abuzar Ghaffari ◽  
Waqar Khan ◽  
Irfan Mustafa
Keyword(s):  
Aspect Ratio ◽  
Entropy Generation ◽  
Temperature Jump ◽  
Slip Flow ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Generation Model ◽  
Minimum Entropy ◽  
Dimensionless Numbers ◽  
Minimum Entropy Generation

In this study, the influence of slip flow and temperature jump on the entropy generation rate are investigated in rectangular microducts. The Knudsen numbers are considered in the range between 0.001 and 0.1, and the aspect ratio lies between 0 and 1. The dimensionless governing equations are solved numerically using Chebyshev spectral collocation method, and the dimensionless velocity and temperature gradients are employed in the entropy generation model. The influences of the dimensionless numbers including Bejan number and irreversibility distribution ratio on the entropy generation rates are investigated and discussed through surface plots and contour diagrams. It is demonstrated that the minimum entropy generation rate exists corresponding to an optimal aspect ratio for each dimensionless number. This minimum entropy generation rate depends upon the nature of dimensionless numbers.

Second-Law Analysis on Wavy Plate Fin-and-Tube Heat Exchangers

1998 ◽  
Vol 120 (3) ◽  
pp. 797-800 ◽  
Author(s):  
W. W. Lin ◽  
D. J. Lee
Keyword(s):  
Entropy Generation ◽  
Operating Conditions ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Second Law ◽  
Spanwise Direction ◽  
Minimum Entropy ◽  
Tube Heat Exchanger ◽  
Second Law Analysis ◽  
Minimum Entropy Generation

Second-law analysis on the herringbone wavy plate fin-and-tube heat exchanger was conducted on the basis of correlations of Nusselt number and friction factor proposed by Kim et al. (1997), from which the entropy generation rate was evaluated. Optimum Reynolds number and minimum entropy generation rate were found over different operating conditions. At a fixed heat duty, the in-line layout with a large tube spacing along streamwise direction was recommended. Furthermore, within the valid range of Kim et al.’s correlation, effects of the fin spacing and the tube spacing along spanwise direction on the second-law performance are insignificant.

scholarly journals Fluid Flow and Entropy Generation Analysis of Al2O3–Water Nanofluid in Microchannel Plate Fin Heat Sinks

Entropy ◽  
2019 ◽  
Vol 21 (8) ◽  
pp. 739 ◽  
Author(s):  
Hao Ma ◽  
Zhipeng Duan ◽  
Liangbin Su ◽  
Xiaoru Ning ◽  
Jiao Bai ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Microchannel Plate ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Nanoparticle Volume Fraction ◽  
Channel Aspect Ratio

The flow in channels of microdevices is usually in the developing regime. Three-dimensional laminar flow characteristics of a nanofluid in microchannel plate fin heat sinks are investigated numerically in this paper. Deionized water and Al2O3–water nanofluid are employed as the cooling fluid in our work. The effects of the Reynolds number (100 < Re < 1000), channel aspect ratio (0 < ε < 1), and nanoparticle volume fraction (0.5% < Φ < 5%) on pressure drop and entropy generation in microchannel plate fin heat sinks are examined in detail. Herein, the general expression of the entropy generation rate considering entrance effects is developed. The results revealed that the frictional entropy generation and pressure drop increase as nanoparticle volume fraction and Reynolds number increase, while decrease as the channel aspect ratio increases. When the nanoparticle volume fraction increases from 0 to 3% at Re = 500, the pressure drop of microchannel plate fin heat sinks with ε = 0.5 increases by 9%. It is demonstrated that the effect of the entrance region is crucial for evaluating the performance of microchannel plate fin heat sinks. The study may shed some light on the design and optimization of microchannel heat sinks.

Numerical Investigation of Local Entropy Generation for Laminar Flow in Rotating-Disk Systems

2010 ◽  
Vol 132 (9) ◽  
Author(s):  
Mohammad Shanbghazani ◽  
Vahid Heidarpoor ◽  
Marc A. Rosen ◽  
Iraj Mirzaee
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Laminar Flow ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Bejan Number ◽  
Local Entropy ◽  
Fluid Friction ◽  
Local Entropy Generation

The entropy generation is investigated numerically in axisymmetric, steady-state, and incompressible laminar flow in a rotating single free disk. The finite-volume method is used for solving the momentum and energy equations needed for the determination of the entropy generation due to heat transfer and fluid friction. The numerical model is validated by comparing it to previously reported analytical and experimental data for momentum and energy. Results are presented in terms of velocity distribution, temperature, local entropy generation rate, Bejan number, and irreversibility ratio distribution for various rotational Reynolds number and physical cases, using dimensionless parameters. It is demonstrated that increasing rotational Reynolds number increases the local entropy generation rate and irreversibility rate, and that the irreversibility is mainly due to heat transfer while the irreversibility associated with fluid friction is minor.

Entropy Generation Minimization in a Pressure-Driven Microflow of Viscoelastic Fluid With Slippage at the Wall: Effect of Conjugate Heat Transfer

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Rajkumar Sarma ◽  
Pranab Kumar Mondal
Keyword(s):  
Heat Transfer ◽  
Viscoelastic Fluid ◽  
Entropy Generation ◽  
Conjugate Heat Transfer ◽  
Applied Pressure ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Viscoelastic Parameter ◽  
Entropy Generation Minimization

We focus on the entropy generation minimization for the flow of a viscoelastic fluid through a parallel plate microchannel under the combined influences of applied pressure gradient, interfacial slip, and conjugate heat transfer. We use the simplified Phan–Thien–Tanner model (s-PTT) to represent the rheological behavior of the viscoelastic fluid. Using thermal boundary conditions of the third kind, we solve the transport equations analytically to obtain the velocity and temperature distributions in the flow field, which are further used to calculate the entropy generation rate in the analysis. In this study, the influential role of the following dimensionless parameters on entropy generation rate is examined: the viscoelastic parameter (εDe2), slip coefficient (k¯), channel wall thickness (δ), thermal conductivity of the wall (γ), Biot number (Bi) and Peclet number (Pe). We show that there exists a particular value of the abovementioned parameters that lead to a minimum entropy generation rate in the system. We believe the results of this analysis could be of helpful in the optimum design of microfluidic system/devices typically used in thermal management, such as micro-electronic devices, microreactors, and microheat exchangers.

scholarly journals Analytical and numerical study of entropy generation in small scale heat exchangers

2019 ◽  
Author(s):  
Mahyar Pourghasemi
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Energy Harvesting ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Optimum Operating ◽  
Maximum Pressure ◽  
Channel Height ◽  
Maximum Pressure Drop

In present work, the entropy generation minimization technique (EGM) is applied to study the performance of a microchannel heat sink combined with a new proposed parameter called irreversibility index and energy harvesting concept. Three different cases have been investigated using geometry of a microchanel heat sink selected from experimental work in the literature. The constraints considered in this study, are fixed channel height and maximum pressure drop. It has been observed that with fixed channel height constraint, while the aspect ratio changes from 1 to 10, the optimum operating condition fall in the range of Reynolds number equal to 2000 and aspect ratio of 2.25. Moreover, the extra constrain on maximum pressure drop imposes a limitation on applicable aspect ratio range. The maximum aspect ratio of the channel for stable flow field in this case cannot be higher than 5 imposed by criteria of laminar flow regime. The obtained optimum values are Reynolds number of 1850 and aspect ratio of 2. Using a combined new defined irreversibility index and Energy Harvesting Concept (EHC), it has been shown that the optimum design values for industrial applications are not necessary ones obtained from EGM method and may shift to a new operating point based on the method considered for energy harvesting.

FLOW SUBJECTED TO A POROUS BLOCK: INFLUENCE OF BODY ASPECT RATIO ON ENTROPY GENERATION RATE

2012 ◽  
Vol 15 (2) ◽  
pp. 137-152
Author(s):  
S. Z. Shuja ◽  
Bekir S. Yilbas
Keyword(s):  
Aspect Ratio ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Porous Block

Genetic Algorithm-Based Optimal Design of Plate Fins Following Minimum Entropy Generation Considerations

2005 ◽  
Vol 219 (8) ◽  
pp. 757-765 ◽  
Author(s):  
R. K. Jha ◽  
S Chakraborty
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Optimal Design ◽  
Forced Convection ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Minimum Entropy Generation ◽  
Continuous Plate

This paper deals with estimation of the optimal dimensions of arrays of plate fins cooled by forced convection. The optimization is achieved by minimizing the entropy generation rate using genetic algorithm-based evolutionary computing techniques. Results are presented for staggered plate fins configuration and continuous plate fins configuration. The effects of heat transfer and fluid friction on entropy generation rate are also reported.

Sign in / Sign up

Export Citation Format

Share Document