Entropy Generation Minimization in a Pressure-Driven Microflow of Viscoelastic Fluid With Slippage at the Wall: Effect of Conjugate Heat Transfer

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Rajkumar Sarma ◽  
Pranab Kumar Mondal
Keyword(s):  
Heat Transfer ◽  
Viscoelastic Fluid ◽  
Entropy Generation ◽  
Conjugate Heat Transfer ◽  
Applied Pressure ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Viscoelastic Parameter ◽  
Entropy Generation Minimization

We focus on the entropy generation minimization for the flow of a viscoelastic fluid through a parallel plate microchannel under the combined influences of applied pressure gradient, interfacial slip, and conjugate heat transfer. We use the simplified Phan–Thien–Tanner model (s-PTT) to represent the rheological behavior of the viscoelastic fluid. Using thermal boundary conditions of the third kind, we solve the transport equations analytically to obtain the velocity and temperature distributions in the flow field, which are further used to calculate the entropy generation rate in the analysis. In this study, the influential role of the following dimensionless parameters on entropy generation rate is examined: the viscoelastic parameter (εDe2), slip coefficient (k¯), channel wall thickness (δ), thermal conductivity of the wall (γ), Biot number (Bi) and Peclet number (Pe). We show that there exists a particular value of the abovementioned parameters that lead to a minimum entropy generation rate in the system. We believe the results of this analysis could be of helpful in the optimum design of microfluidic system/devices typically used in thermal management, such as micro-electronic devices, microreactors, and microheat exchangers.

Genetic Algorithm-Based Optimal Design of Plate Fins Following Minimum Entropy Generation Considerations

2005 ◽  
Vol 219 (8) ◽  
pp. 757-765 ◽  
Author(s):  
R. K. Jha ◽  
S Chakraborty
Keyword(s):  
Heat Transfer ◽  
Genetic Algorithm ◽  
Optimal Design ◽  
Forced Convection ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Minimum Entropy Generation ◽  
Continuous Plate

This paper deals with estimation of the optimal dimensions of arrays of plate fins cooled by forced convection. The optimization is achieved by minimizing the entropy generation rate using genetic algorithm-based evolutionary computing techniques. Results are presented for staggered plate fins configuration and continuous plate fins configuration. The effects of heat transfer and fluid friction on entropy generation rate are also reported.

The Equivalence of Maximum Power and Minimum Entropy Generation Rate in the Optimization of Power Plants

1996 ◽  
Vol 118 (2) ◽  
pp. 98-101 ◽  
Author(s):  
Adrian Bejan
Keyword(s):  
Heat Transfer ◽  
Power Plant ◽  
Entropy Generation ◽  
Heat Input ◽  
Power Plants ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Total Entropy ◽  
Minimum Entropy ◽  
Minimum Entropy Generation

It is shown that to maximize the power output of a power plant is equivalent to minimizing the total entropy generation rate associated with the power plant. This equivalence is illustrated by using two of the oldest and simplest models of power plants with heat transfer irreversibilities. To calculate the total entropy generation rate correctly, one must recognize that the optimization process (e.g., the variability of the heat input) requires “room to move,” i.e., an additional, usually overlooked, contribution to the total entropy generation rate.

A Holistic Optimization of Convecting-Radiating Fin Systems

2002 ◽  
Vol 124 (6) ◽  
pp. 1110-1116 ◽  
Author(s):  
M. Sasikumar ◽  
C. Balaji
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Entropy Generation ◽  
Transfer Rate ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Fluid Temperature ◽  
Minimum Entropy ◽  
Maximum Heat ◽  
Unit System

A convecting-radiating fin array, which stands vertically outside of a horizontal rectangular duct, has been analyzed for various design constraints. Fully developed turbulent flow is considered inside the duct. This study takes into account the variation of fluid temperature along the duct, which has been ignored in most of the earlier studies. The one-dimensional governing equation for temperature distribution along the fin is solved for all the fins of the fin array and the total heat transfer rate per unit system mass, total entropy generation rate and optimum fin height based on maximum heat transfer rate per unit system mass are evaluated from the derived temperature profiles. These quantities are then correlated as functions of geometric and flow parameters for three types of fin profile. Optimum solutions are generated based on (i) maximum heat dissipation rate per unit system mass and (ii) minimum entropy generation rate. A procedure to combine these two optima in order to obtain a “holistic” optimum is also discussed.

The Role of Fin Geometry in Heat Sink Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 324-330 ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Entropy Generation ◽  
Heat Sink ◽  
Control Volume ◽  
Generation Rate ◽  
Heat Transfer Fluid ◽  
Entropy Generation Rate ◽  
Minimum Entropy ◽  
Axis Ratio

The following study will examine the effect on overall thermal/fluid performance associated with different fin geometries, including, rectangular plate fins as well as square, circular, and elliptical pin fins. The use of entropy generation minimization, EGM, allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including base plate and applying the conservations equations for mass and energy with the entropy balance. The formulation for the dimensionless entropy generation rate is developed in terms of dimensionless variables, including the aspect ratio, Reynolds number, Nusselt number, and the drag coefficient. Selected fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate corresponding to different parameters including axis ratio, aspect ratio, and Reynolds number. The results clearly indicate that the preferred fin profile is very dependent on these parameters.

Second-Law Analysis on Wavy Plate Fin-and-Tube Heat Exchangers

1998 ◽  
Vol 120 (3) ◽  
pp. 797-800 ◽  
Author(s):  
W. W. Lin ◽  
D. J. Lee
Keyword(s):  
Entropy Generation ◽  
Operating Conditions ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Second Law ◽  
Spanwise Direction ◽  
Minimum Entropy ◽  
Tube Heat Exchanger ◽  
Second Law Analysis ◽  
Minimum Entropy Generation

Second-law analysis on the herringbone wavy plate fin-and-tube heat exchanger was conducted on the basis of correlations of Nusselt number and friction factor proposed by Kim et al. (1997), from which the entropy generation rate was evaluated. Optimum Reynolds number and minimum entropy generation rate were found over different operating conditions. At a fixed heat duty, the in-line layout with a large tube spacing along streamwise direction was recommended. Furthermore, within the valid range of Kim et al.’s correlation, effects of the fin spacing and the tube spacing along spanwise direction on the second-law performance are insignificant.

Numerical Investigation of Local Entropy Generation for Laminar Flow in Rotating-Disk Systems

2010 ◽  
Vol 132 (9) ◽  
Author(s):  
Mohammad Shanbghazani ◽  
Vahid Heidarpoor ◽  
Marc A. Rosen ◽  
Iraj Mirzaee
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Laminar Flow ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Bejan Number ◽  
Local Entropy ◽  
Fluid Friction ◽  
Local Entropy Generation

The entropy generation is investigated numerically in axisymmetric, steady-state, and incompressible laminar flow in a rotating single free disk. The finite-volume method is used for solving the momentum and energy equations needed for the determination of the entropy generation due to heat transfer and fluid friction. The numerical model is validated by comparing it to previously reported analytical and experimental data for momentum and energy. Results are presented in terms of velocity distribution, temperature, local entropy generation rate, Bejan number, and irreversibility ratio distribution for various rotational Reynolds number and physical cases, using dimensionless parameters. It is demonstrated that increasing rotational Reynolds number increases the local entropy generation rate and irreversibility rate, and that the irreversibility is mainly due to heat transfer while the irreversibility associated with fluid friction is minor.

Modeling heat transfer of nanofluid flow in microchannels with electrokinetic and slippery effects using Buongiorno’s model

2019 ◽  
Vol 29 (8) ◽  
pp. 2566-2587 ◽  
Author(s):  
Hang Xu ◽  
Huang Huang ◽  
Xiao-Hang Xu ◽  
Qiang Sun
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Slip Length ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Lower Wall ◽  
Volumetric Concentration ◽  
Nanofluid Flow ◽  
Cross Sectional ◽  
Content Type

PurposeThis paper aims to study the heat transfer of nanofluid flow driven by the move of channel walls in a microchannel under the effects of the electrical double layer and slippery properties of channel walls. The distributions of velocity, temperature and nanoparticle volumetric concentration are analyzed under different slip-length. Also, the variation rates of flow velocity, temperature, concentration of nanoparticle, the pressure constant, the local volumetric entropy generation rate and the total cross-sectional entropy generation are analyzed.Design/methodology/approachA recently developed model is chosen which is robust and reasonable from the point of view of physics, as it does not impose nonphysical boundary conditions, for instance, the zero electrical potential in the middle plane of the channel or the artificial pressure constant. The governing equations of flow motion, energy, electrical double layer and stream potential are derived with slip boundary condition presented. The model is non-dimensionalized and solved by using the homotopy analysis method.FindingsSlip-length has significant influences on the velocity, temperature and nanoparticle volumetric concentration of the nanofluid. It also has strong effects on the pressure constant. With the increase of the slip-length, the pressure constant of the nanofluid in the horizontal microchannel decreases. Both the local volumetric entropy generation rate and total cross-sectional entropy generation rate are significantly affected by both the slip-length of the lower wall and the thermal diffusion. The local volumetric entropy generation rate at the upper wall is always higher than that around the lower wall. Also, the larger the slip-length is, the lower the total cross-sectional entropy generation rate is when the thermal diffusion is moderate.Originality/valueThe findings in this work on the heat transfer and flow phenomena of the nanofluid in microchannel are expected to make a contribution to guide the design of micro-electro-mechanical systems.

Thermodynamic Analysis of Magnetohydrodynamic Third Grade Fluid Flow with Variable Properties

2021 ◽  
Vol 55 ◽  
pp. 28-46
Author(s):  
Kgomotshwana Frans Thosago ◽  
Lazarus Rundora ◽  
Samuel Olumide Adesanya
Keyword(s):  
Fluid Flow ◽  
Thermodynamic Analysis ◽  
Entropy Generation ◽  
Generation Rate ◽  
Third Grade ◽  
Entropy Generation Rate ◽  
Bejan Number ◽  
Third Grade Fluid ◽  
Entropy Generation Minimization ◽  
Grade Fluid

This article aims to computationally study entropy generation in a magnetohydrodynamic (MHD) third grade fluid flow in a horizontal channel with impermeable walls. The fluids viscosity and thermal conductivity are assumed to be dependent on temperature. The flow is driven by an applied uniform axial pressure gradient between infinite parallel plates and is considered to be incompressible, steady and fully developed. Adomian decomposition method (ADM) is used to obtain series solutions of the nonlinear governing equations. Thermodynamic analysis is done by computing the entropy generation rate and the irreversibility ratio (Bejan number). The effects of the various pertinent embedded parameters on the velocity field, temperature field, entropy generation rate and Bejan number are analysed through vivid graphical manipulations. The analysis shows that an appropriate combination of thermophysical parameters efficiently achieves entropy generation minimization in the thermomechanical system. The analysis shows that entropy generation minimization is achieved by increasing the magnetic field and the third grade material parameters, and therefore designs and processes incorporating MHD third grade fluid flow systems are far more likely to give optimum and efficient performance.

Optimization of Pin-Fin Heat Sinks in Bypass Flow Using Entropy Generation Minimization Method

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
W. A. Khan ◽  
J. R. Culham ◽  
M. M. Yovanovich
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Heat Sink ◽  
Heat Sinks ◽  
Entropy Generation Rate ◽  
Bypass Flow ◽  
Minimization Method ◽  
Pin Fin ◽  
Entropy Generation Minimization

An entropy generation minimization method is applied to study the thermodynamic losses caused by heat transfer and pressure drop for the fluid in a cylindrical pin-fin heat sink and bypass flow regions. A general expression for the entropy generation rate is obtained by considering control volumes around the heat sink and bypass regions. The conservation equations for mass and energy with the entropy balance are applied in both regions. Inside the heat sink, analytical/empirical correlations are used for heat transfer coefficients and friction factors, where the reference velocity used in the Reynolds number and the pressure drop is based on the minimum free area available for the fluid flow. In bypass regions theoretical models, based on laws of conservation of mass, momentum, and energy, are used to predict flow velocity and pressure drop. Both in-line and staggered arrangements are studied and their relative performance is compared to the same thermal and hydraulic conditions. A parametric study is also performed to show the effects of bypass on the overall performance of heat sinks.

Sign in / Sign up

Export Citation Format

Share Document