The Undercutting of Circular-Cut Spiral Bevel Gears

1992 ◽  
Vol 114 (2) ◽  
pp. 317-325 ◽  
Author(s):  
Zhang-Hua Fong ◽  
Chung-Biau Tsay
Keyword(s):  
Gear Tooth ◽  
Sufficient Conditions ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Tooth Surfaces ◽  
Sufficient And Necessary Conditions ◽  
Spiral Bevel

Undercutting is a serious problem in designing spiral bevel gears with small numbers of teeth. Conditions of undercutting for spiral bevel gears vary with the manufacturing methods. Based on the theory of gearing [1], the tooth geometry of the Gleason type circular-cut spiral bevel gear is mathematically modeled. The sufficient and necessary conditions for the existence and regularity of the generated gear tooth surfaces are investigated. The conditions of undercutting for a circular-cut spiral bevel gear are defined by the sufficient conditions of the regular gear tooth surface. The derived undercutting equations can be applicable for checking the undercutting conditions of spiral bevel gears manufactured by the Gleason Duplex Method, Helical Duplex Method, Fixed Setting Method, and Modified Roll Method. An example is included to illustrate the application of the proposed undercut checking equations.

Designing and Manufacturing Spiral Bevel Gears Using 5-Axis CNC Milling Machines

2011 ◽  
Author(s):  
Joe¨l Teixeira Alves ◽  
Miche`le Guingand ◽  
Jean-Pierre de Vaujany
Keyword(s):  
Manufacturing Process ◽  
Gear Tooth ◽  
Bevel Gear ◽  
Spiral Bevel Gear ◽  
Milling Machine ◽  
Cnc Milling ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Tooth Surfaces ◽  
Spiral Bevel

The design of spiral bevel gears still remains complex since tooth geometry and the resulting kinematics performance stem directly from the manufacturing process. Spiral bevel gear manufacture owes most to the works of Gleason and Klingelnberg. However, recent advances in milling machine technology and CAM (Computer Aided Manufacturing) make it possible to manufacture good quality spiral bevel gears on a standard 5-axis milling machine. This paper describes the CAD definition and manufacturing of spiral bevel gear tooth surfaces. Process performance is assessed by comparing the resulting surfaces after machining with the pre-defined CAD surfaces. Using this manufacturing process allows to propose new type of geometry. This one is more theoretical and, in some respects, easier to design than the standard spiral bevel gear as it enables simpler mesh optimization. The latter can be achieved by using the model of meshing under load recalled in this paper.

scholarly journals Lubrication characteristics of gear after shot peening base on 25-pellet model

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401879065 ◽  
Author(s):  
Shuai Mo ◽  
Shengping Zhu ◽  
Guoguang Jin ◽  
Jiabei Gong ◽  
Zhanyong Feng ◽  
...  
Keyword(s):  
Shot Peening ◽  
High Speed ◽  
Target Material ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel ◽  
Lubrication Characteristics

High-speed heavy-load spiral bevel gears put forward high requirement for flexural strength; shot peening is a technique that greatly improves the bending fatigue strength of gears. During shot peening, a large number of fine pellets bombard the surface of the metal target material at very high speeds and let the target material undergo plastic deformation, at the same time strengthening layer is produced. Spiral bevel gear as the object of being bombarded inevitably brought the tooth surface micro-morphology changes. In this article, we aim to reveal the effect of microtopography of tooth shot peening on gear lubrication in spiral bevel gear, try to establish a reasonable description of the microscopic morphology for tooth surface by shot peening, to reveal the lubrication characteristics of spiral bevel gears after shot peening treatment based on the lubrication theory, and do comparative research on the surface lubrication characteristics of a variety of microstructures.

Kinematical Optimization of Spiral Bevel Gears

1992 ◽  
Author(s):  
Zhang-Hua Fong ◽  
Chung-Biau Tsay
Keyword(s):  
Mathematical Model ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Tooth Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Contact Patterns ◽  
Spiral Bevel ◽  
Kinematic Errors

Abstract Kinematical optimization and sensitivity analysis of circular-cut spiral bevel gears are investigated in this paper. Based on the Gleason spiral bevel gear generator and EPG test machine, a mathematical model is proposed to simulate the tooth contact conditions of the spiral bevel gear set. All the machine settings and assembly data are simulated by simplified parameters. The tooth contact patterns and kinematic errors are obtained by the proposed mathematical model and the tooth contact analysis techniques. Loaded tooth contact patterns are obtained by the differential geometry and the Hertz contact formulas. Tooth surface sensitivity due to the variation of machine settings is studied. The corrective machine settings can be calculated by the sensitive matrix and the linear regression method. An optimization algorithm is also developed to minimize the kinematic errors and the discontinuity of tooth meshing. According to the proposed studies, an improved procedure for development of spiral bevel gears is suggested. The results of this paper can be applied to determine the sensitivity and precision requirements in manufacturing, and improve the running quality of the spiral bevel gears. Two examples are presented to demonstrate the applications of the optimization model.

scholarly journals Surface Geometry of Circular Cut Spiral Bevel Gears

1982 ◽  
Vol 104 (4) ◽  
pp. 743-748 ◽  
Author(s):  
R. L. Huston ◽  
J. J. Coy
Keyword(s):  
Logarithmic Spiral ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Surface Geometry ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel

An analysis of the surface geometry of spiral bevel gears formed by a circular cutter is presented. The emphasis is upon determining the tooth surface principal radii of curvature of crown (flat) gears. Specific results are presented for involute, straight, and hyperbolic cutter profiles. It is shown that the geometry of circular cut spiral bevel gears is somewhat simpler than a theoretical logarithmic spiral bevel gear.

Research on Curvature of Tooth Flank of Gleason Spiral Bevel Gears

2011 ◽  
Vol 189-193 ◽  
pp. 4256-4260
Author(s):  
Ai Mei Zhang ◽  
Lin Yan Li ◽  
Da Wei Li
Keyword(s):  
Mean Curvature ◽  
Gear Tooth ◽  
Three Dimensional ◽  
Processing Parameters ◽  
Bevel Gear ◽  
Machining Process ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Tooth Surfaces ◽  
Spiral Bevel

According to spiral bevel gear machining process, use the method of computer simulation to get the discrete points’ three-dimensional coordinates of Gleason spiral bevel gear tooth surface, and then solve the tooth surfaces’ NURBS surface as the unified mathematical model. On this basis, research the curvature of tooth surfaces of various types of Gleason spiral bevel gear, draw the mean curvature diagram, and study the link between the adjustment of processing parameters and the change of tooth surfaces’ mean curvature. Establish a theoretical foundation for the processing error adjustment based on tooth surface’s curvature diagram.

scholarly journals EHL Analysis of Spiral Bevel Gear Pairs considering the Contact Point Migration due to Deformation under Load

2020 ◽  
Vol 2020 ◽  
pp. 1-19
Author(s):  
Xiaoyu Sun ◽  
Yanping Liu ◽  
Yongqiang Zhao ◽  
Ming Liu
Keyword(s):  
Contact Point ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Gear Pair ◽  
Spiral Bevel Gears ◽  
Actual Contact ◽  
Bevel Gears ◽  
Contact Points ◽  
Spiral Bevel

The actual contact point of a spiral bevel gear pair deviates from the theoretical contact point due to the gear deformation caused by the load. However, changes in meshing characteristics due to the migration of contact points are often ignored in previous studies on the elastohydrodynamic lubrication (EHL) analysis of spiral bevel gears. The purpose of this article is to analyze the impact of contact point migration on the results of EHL analysis. Loaded tooth contact analysis (LTCA) based on the finite element method is applied to determine the loaded contact point of the meshing tooth pair. Then, the osculating paraboloids at this point are extracted from the gear tooth surface geometry. The geometric and kinematic parameters for EHL simulation are determined according to the differential geometry theory. Numerical solutions to the Newtonian isothermal EHL of a spiral bevel gear pair at the migrated and theoretical contact points are compared to quantify the error involved in neglecting the contact point adjustment. The results show that under heavy-loaded conditions, the actual contact point of the deformed gear pair at a given pinion (gear) roll angle is different from the theoretical contact point considerably, and so do the meshing parameters. EHL analysis of spiral bevel gears under significant load using theoretical meshing parameters will result in obvious errors, especially in the prediction of film thickness.

Kinematical Optimization of Spiral Bevel Gears

1992 ◽  
Vol 114 (3) ◽  
pp. 498-506 ◽  
Author(s):  
Zhang-Hua Fong ◽  
Chung-Biau Tsay
Keyword(s):  
Mathematical Model ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Tooth Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Contact Patterns ◽  
Spiral Bevel ◽  
Kinematic Errors

Kinematical optimization and sensitivity analysis of circular-cut spiral bevel gears are investigated in this paper. Based on the Gleason spiral bevel gear generator and EPG test machine, a mathematical model is proposed to simulate the tooth contact conditions of the spiral bevel gear set. All the machine settings and assembly data are simulated by simplified parameters. The tooth contact patterns and kinematic errors are obtained by the proposed mathematical model and the tooth contact analysis techniques. Loaded tooth contact patterns are obtained by the differential geometry and the Hertz contact formulas. Tooth surface sensitivity due to the variation of machine settings is studied. The corrective machine settings can be calculated by the sensitive matrix and the linear regression method. An optimization algorithm is also developed to minimize the kinematic errors and the discontinuity of tooth meshing. According to the proposed studies, an improved procedure for development of spiral bevel gears is suggested. The results of this paper can be applied to determine the sensitivity and precision requirements in manufacturing, and improve the running quality of the spiral bevel gears. Two examples are presented to demonstrate the applications of the optimization model.

Mathematical Model and 3D Modeling of Involute Spiral Bevel Gears for Nutation Drive

2013 ◽  
Vol 694-697 ◽  
pp. 503-506 ◽  
Author(s):  
Zheng Lin ◽  
Li Gang Yao
Keyword(s):  
Mathematical Model ◽  
3D Modeling ◽  
Bevel Gear ◽  
Transition Curve ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel ◽  
The Mathematical Model

The mathematical model and 3D modeling of involute spiral bevel gears for nutation drive are considered. The basic tooth profile of involute is composed of involute curve and dedendum transition curve, and the equations have been established. The mathematical model of crown gear with involute profile is obtained, and then the mathematical models of the involute spiral bevel gears are developed. The tooth surface modeling of involute spiral bevel gear is proposed, and the 3D modeling of the involute spiral bevel gear for nutation drive is illustrated.

A Study on Forging of Spiral Bevel Gear

2007 ◽  
Author(s):  
Masaki Watanabe ◽  
Minoru Maki ◽  
Sumio Hirokawa ◽  
Yasuhiro Kishimoto
Keyword(s):  
Gear Tooth ◽  
Conjugate Point ◽  
Point Contact ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Tooth Contact ◽  
Contact Points ◽  
Tooth Surfaces ◽  
Spiral Bevel

This study reports the method of forging of spiral bevel gear. Two ideas for crowning of tooth surface to obtain point contact for forging gears are proposed. By one idea, tooth surface of pinion meshes with the gear tooth surface by conjugate point contact. And the trace of contact points on the gear tooth surface is perpendicular to the lengthwise direction of gear tooth, namely becomes the “square contact” so called in gear technology. The trace can be set arbitrarily on the gear tooth, by setting the pitch point arbitrarily. By another idea, the trace of contact points lies along the tooth trace of the gear tooth. Both ideas proposed in this report, the numerical dataset of teeth surface of pinion and gear are given by the contact lines with the cutter cone. The dataset of teeth surface of pinion and gear are calculated to cut a pair of electrodes of spiral bevel gear. Tooth contacts of proposed gearing are confirmed by the 3D drawing of tooth surfaces. The tooth contact of the master pinion and gear were made and tested by tooth contact testing apparatus. The contact marks coincide well with the theoretical contact pattern estimated by 3D/CAD expression. The good results of running test of the performance of the master gear has been given. The authors completed the forging of spiral bevel gear pairs by two methods proposed in this report.

New Geometry of Generating Spiral Bevel Gear

2007 ◽  
Author(s):  
Kaihong Zhou ◽  
Jinyuan Tang ◽  
Tao Zeng
Keyword(s):  
Gear Tooth ◽  
Previous Method ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Surface Geometry ◽  
Numerical Examples ◽  
Cone Surface ◽  
Spiral Bevel ◽  
Involute Curve

New geometry of generating spiral bevel gear is proposed. The key idea of the new proposed geometry is that the gear tooth surface geometry can be investigated in a developed curved surface based on the planar engagement principle. It is proved that the profile curve on the back of generating cone surface is a conical involute curve. The equations of generated gear tooth surface are achieved by the conical involute curve sweeping along the tooth trace of gear. The obtained equations are explicit and independent of the machine-tool settings. This differs from previous studies. The developed theory is illustrated with numerical examples to compare with the previous method, the comparison approves that the method is possible in this way. The new method indicates that there are new solutions to the design the production of spiral bevel gear.

Sign in / Sign up

Export Citation Format

Share Document