Experimental and Numerical Study of Jet Impingement Cooling for Improved Gas Turbine Blade Internal Cooling With In-Line and Staggered Nozzle Arrays

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Abdel Rahman Salem ◽  
Farah Nazifa Nourin ◽  
Mohammed Abousabae ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Numerical Study ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Target Surface ◽  
Internal Cooling ◽  
Impingement Cooling ◽  
Gas Turbine Blades

Abstract Internal cooling of gas turbine blades is performed with the combination of impingement cooling and serpentine channels. Besides gas turbine blades, the other turbine components such as turbine guide vanes, rotor disks, and combustor wall can be cooled using jet impingement cooling. This study is focused on jet impingement cooling, in order to optimize the coolant flow, and provide the maximum amount of cooling using the minimum amount of coolant. The study compares between different nozzle configurations (in-line and staggered), two different Reynold's numbers (1500 and 2000), and different stand-off distances (Z/D) both experimentally and numerically. The Z/D considered are 3, 5, and 8. In jet impingement cooling, the jet of fluid strikes perpendicular to the target surface to be cooled with high velocity to dissipate the heat. The target surface is heated up by a direct current (DC) power source. The experimental results are obtained by means of thermal image processing of the captured infra-red (IR) thermal images of the target surface. Computational fluid dynamics (CFD) analysis were employed to predict the complex heat transfer and flow phenomena, primarily the line-averaged and area-averaged Nusselt number and the cross-flow effects. In the current investigation, the flow is confined along with the nozzle plate and two parallel surfaces forming a bi-directional channel (bi-directional exit). The results show a comparison between heat transfer enhancement with in-line and staggered nozzle arrays. It is observed that the peaks of the line-averaged Nusselt number (Nu) become less as the stand-off distance (Z/D) increases. It is also observed that the fluctuations in the stagnation heat transfer are caused by the impingement of the primary vortices originating from the jet nozzle exit.

Conjugate Heat Transfer Simulation and Entropy Generation Analysis of Gas Turbine Blades

2021 ◽  
Author(s):  
Yaping Ju ◽  
Yi Feng ◽  
Chuhua Zhang
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Entropy Generation ◽  
Conjugate Heat Transfer ◽  
Turbine Blades ◽  
Measurement Data ◽  
Turbulence Models ◽  
Internal Cooling ◽  
Gas Turbine Blades ◽  
Internally Cooled

Abstract Reynolds averaged Navier-Stokes model-based conjugate heat transfer method is popularly used in simulations and designs of internally cooled gas turbine blades. One of the important factors influencing its prediction accuracy is the choice of turbulence models for different fluid regions because the blade passage flow and internal cooling have considerably different flow features. However, most studies adopted the same turbulence models in passage flow and internal cooling. Another important issue is the comprehensive evaluation of the losses caused by flow and heat transfer for both fluid and solid regions. In this study, a RANS-based CHT solver for subsonic/transonic flows was developed based on OpenFOAM and validated and used to explore suitable RANS turbulence model combinations for internally cooled gas turbine blades. Entropy generation, able to weigh the losses caused by flow friction and heat transfer, was used in the analyses of two internally cooled vanes to reveal the loss mechanisms. Findings indicate that the combination of the k-? SST-?-Re? transition model for passage flow and the standard k-e model for internal cooling agreed best with measurement data. The relative error of vane dimensionless temperature was less than 3%. The variations of entropy generation with different internal cooling inlet velocities and temperatures indicate that reducing entropy generation was contradictory with enhancing heat transfer performance. This study, providing a reliable computing tool and a comprehensive performance parameter, has an important application value for the design of internally cooled gas turbine blades.

Numerical Study of Flow and Heat Transfer of Impingement Cooling on Model of Turbine Blade Leading Edge

2010 ◽  
Author(s):  
Zhao Liu ◽  
Zhenping Feng ◽  
Liming Song
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Numerical Study ◽  
Leading Edge ◽  
Jet Impingement ◽  
Target Surface ◽  
Nozzle Diameter ◽  
Impingement Cooling ◽  
Jet Nozzle ◽  
Blade Leading Edge

In this paper a numerical simulation is performed to simulate the impingement cooling on internal leading edge region, which is stretched by the middle cross section of the first stage rotor blade of GE-E3 engine high pressure turbine, and in the condition that jets flow is ejected from a row of four different diameter circular nozzles. The relative performances of three versions of turbulence models including the RNG κ-ε model, the standard κ-ω model and the SST κ-ω model in the simulation of a row of circle jet impingement heat transfer are compared with available experimental data. The results show that SST κ-ω model is the best one based on simulation accuracy. Then the SST κ-ω model is adopted for the simulation. The grid independence study is also carried out by using the Richardson extrapolation method. A single array of circle jets is arranged to investigate the impingement cooling and its effectiveness. Four different jet nozzle diameters are studied and seven different inlet flow Mach numbers of each jet nozzle diameter are calculated. The influence of the ratio of the spacing of jet nozzle from the target surface to the jet nozzle diameter on impingement cooling is also studied, in case of a constant ratio of jet spacing to jet nozzle diameter in different jet nozzle diameters. The results indicate that the heat transfer coefficient on the turbine blade leading edge increases with the increase of jet Mach number and jet nozzle diameter, the spanwise area weight average Nusselt number decreases with the increase of the ratio of the spacing of jet nozzle from the target surface to jet nozzle diameter, and a lower ratio of spacing of jet nozzle from the target surface to the jet nozzle diameter is desirable to improve the performance of impingement cooling on turbine leading edge.

Experimental/Numerical Study of Multiple Rows of Confined Jet Impingement Normal to a Surface at Close Distances

2012 ◽  
Author(s):  
M. E. Taslim ◽  
N. Rosso
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Numerical Study ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Hole Diameter ◽  
Impingement Cooling ◽  
Discharge Coefficients ◽  
Hexahedral Elements ◽  
D Values

Impingement cooling is used in a variety of applications ranging from industrial bakeries, paper processing, heat exchangers and specially gas turbine engines of all sizes to name a few. Convective impingement cooling has been studied numerous times in a variety of configurations. However little work has been conducted regarding impingement between two surfaces separated by less than one impingement jet hole diameter. This configuration is of special interest for gas turbine cooling applications such as in shrouds, combustor liners and airfoils cooling cavities where small holes are used to cool and purge cavities between two adjacent pieces of hardware. In this study, flow and temperature fields as well as heat transfer coefficients for confined jet impingement are being investigated for multiple rows of round jets impinging normal to a target surface less than one hole diameter from the jet origin. The experiments were conducted for five rows of jets with five jets on each row and steady-state liquid crystal thermography for heat transfer measurements were utilized. Numerical results were obtained from a three-dimensional unstructured computational fluid dynamics model with over 4 million hexahedral elements. For turbulence modeling, the realizable k–ε was employed in combination with enhanced wall treatment approach for the near wall regions. Other available RANS turbulence models such as k–ω, v2f and large eddy simulation were tried for selected geometries and results are compared with those of k–ε model. Nusselt numbers on the target areas and discharge coefficients for flow across the jet holes are reported for jet Reynolds numbers ranging from 10000 to 50000, pitch-to-diameter, P/d, values of 2,3 and 4, each for jet distance-to-diameter Z/d, values of 0.3, 0.4, 0.5, 0.6, 0.8, 1, 2 and 3. Comparisons are made between the test and numerically-obtained results in order to evaluate the employed turbulence models and validate the numerically obtained results. Results showed severe reduction in discharge coefficients as the jet holes were brought closer to each other and closer to the target wall. Heat transfer performance for the hole lateral spacing of P/d = 4 was found to be superior to that for P/d = 2 or P/d = 3.

Effects of Extended Jet Holes to Heat Transfer and Flow Characteristics of the Jet Impingement Cooling

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Ahmet Ümit Tepe ◽  
Kamil Arslan ◽  
Yaşar Yetişken ◽  
Ünal Uysal
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Jet Impingement ◽  
Target Surface ◽  
Impingement Cooling ◽  
Compressor Power

In this study, effects of extended jet holes to heat transfer and flow characteristics of jet impingement cooling were numerically investigated. Cross-flow in the impinging jet cooling adversely affects the heat transfer on the target surface. The main purpose of this study is to reduce the negative effect of cross-flow on heat transfer by extending jet holes toward the target surface with nozzles. This study has been conducted under turbulent flow condition (15,000 ≤ Re  ≤  45,000). The surface of the turbine blade, which is the target surface, has been modeled as a flat plate. The effect of the ribs, placed on the target surface, on the heat transfer has been also investigated, and the results were compared with the flat surface. The parameters such as average and local Nusselt numbers on the target surface, flow characteristics, and compressor power have been examined in detail. It was obtained from the numerical results that the average Nusselt number increases with decreasing the gap between the target surface and the nozzle. In addition, the higher average Nusselt number was obtained on the flat surface than the ribbed surface. The lowest compressor power was achieved in the 5Dj nozzle gap for the flat surface and in the 4Dj nozzle gap for the ribbed surface.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement

2011 ◽  
Author(s):  
Xinjun Wang ◽  
Rui Liu ◽  
Xiaowei Bai ◽  
Jinling Yao
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Target Surface ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer

A mathematical model used for studying jet impingement cooling characteristics is established, and the rationality of the calculation model and method is confirmed by the experimental data. The CFX software is used to numerically simulate the jet impingement cooling characteristics on a gas turbine blade. The effects of various parameters, such as the arrays of impinging nozzles, the jet Reynolds number, the jet-to-jet distance, the ratio of nozzle-to-surface spacing to jet diameter H/d, and the radius of curvature of the target surface, on the flow and heat transfer characteristics of a impingement cooling process are studied. The results indicate that the impingement jets can make complex vortex in the cooling channel, the flow boundary layer is extremely thin and highly turbulent. Underneath each impingement nozzle, there will appear a low temperature area and a peak of Nusselt number on the impingement target surface, the distribution of temperature and Nusselt number on the target surface are associated with arrangement of impingement nozzles. The average Nusselt number of the in-line arrangement nozzles is higher than that of the staggered arrangement ones. With the increasing of jet Reynolds number, the velocity impinging on the target surface and Nusselt number increase. However, heat transfer of impingement cooling on target surface is not sensitive to the jet nozzles distance; the velocity impinging on the target surface and Nusselt number decrease with the increasing of the H/d value. For the curved target surface cases, the average Nusselt number of the target surface and the effect of heat transfer decreased with the increasing of curvature radius R.

scholarly journals Effect of Rotation Number on Heat Transfer Characteristics of a Row of Impinging Jets in Confined Channel

2020 ◽  
Vol 77 (1) ◽  
pp. 161-171
Author(s):  
Thantup Nontula ◽  
Natthaporn Kaewchoothong ◽  
Wacharin Kaew-apichai ◽  
Chayut Nuntadusit
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rotation Number ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Impinging Jets ◽  
Internal Cooling ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Impingement Surface

Jet impingement has been applied for internal cooling in gas turbine blades. In this study, heat transfer characteristics of impinging jets from a row of circular orifices were investigated inside a flow channel with rotations. The Reynolds number (Re) based on the jet mean velocity was fixed at 6,700. Whereas, the rotation number (Ro) of a channel was varied from 0 to 0.0099. The jet-to-impingement distance ratio (L/Dj) and jet pitch ratio (P/Dj) were respective 2 and 4, Dj is a jet diameter of 5 mm. The thermochromic liquid crystals (TLCs) technique was used to measure the heat transfer coefficient distributions on an impingement surface. The results show that heat transfer enhancement on a jet impingement surface depended on the effects of crossflow and Coriolis force. The local Nusselt number at X/Dj?20 on the leading side (LS) was higher than on the trailing side (TS) while heat transfer on the LS at 20?X/Dj?40 gained the lowest, compared to on the TS. The average Nusselt number ratios ( ) on the TS at Ro = 0.0049 gave higher than on the LS of around 2.17%. On the other hand, the on the TS at Ro = 0.0099 was less than the LS of about 0.08%.

Impinging Jet Cooled Plate Fin Heat Sinks With Turbulators Enhancement

2009 ◽  
Author(s):  
Ganesh Subbuswamy ◽  
Xianchang Li
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Sink ◽  
Numerical Study ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Impinging Jets ◽  
Heat Sinks ◽  
Internal Cooling

Extended surfaces (fins) and impinging jets have been used to enhance heat transfer in many applications. In electronic thermal management, heat sinks can be designed to take advantage of the combined effect of fins and jet impingement such as jets impinging on an array of pin fins or plate fins. Significant studies have been focused on the thermal resistance, pressure drop, and the parametric effect of Reynolds number, fin thickness, density, and height. To further improve the heat sink performance, ribs/turbulators, which are widely employed in internal cooling of gas turbine blades, can be integrated into the plate fins, especially close to the surface area with low heat transfer coefficient. Numerical study is performed in this paper to examine the flow and heat transfer behavior of plate fin heat sinks cooled by an impinging jet and enhanced by the ribs. The height and shape of the turbulators are investigated to achieve the best performance. Parametric studies also include the flow Reynolds number and the spacing between the ribs. Heat transfer mechanism is explored for the confined turbulence jet with and without turbulators. It is expected that the rib enhancement can lead to a more cost-effective heat sink for cooling of electronic components. Further enhancement and optimization are discussed in this paper.

Three-Tier Impingement Cooling Design for Gas Turbine Blade Trailing Edge

2018 ◽  
Author(s):  
Kishore Ranganath Ramakrishnan ◽  
Prashant Singh ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Suction Side ◽  
Internal Wall ◽  
Trailing Edge ◽  
Impingement Cooling ◽  
Cooling Design

Gas turbine blades are subjected to elevated heat loads due to highly turbulent hot gases exiting the combustor section. Several internal and external cooling techniques are used to protect the blades from such hostile environment. Trailing edge of a turbine blade is usually cooled with array of staggered cylindrical pins, which connects the pressure and suction side internal walls and hence provide improved structural integrity. However, the heat transfer enhancement levels for array of pin-fins is generally lower than jet impingement and ribbed channels. In this study, we present a three-tier impingement cooling design for blade trailing-edge and part of mid-chord region. In this design, pressure and suction side internal walls are subjected to oblique jet impingement. Three different configurations have been studied where we have systematically varied the jet diameters and number of jets in an array for different tiers. Numerical simulations have been carried out for different flow conditions, which corresponds to Reynolds numbers (based on 1st-passage jet diameter) ranging between 3000 and 46000. First two plenums had high levels of heat transfer due to oblique jet impingement, where the suction side internal wall representative surface, had higher heat transfer compared to the pressure side internal wall. Third tier had the lowest heat transfer due to triangle-like configuration where jets were almost parallel to pressure and suction side surfaces, and hence their effectiveness was lower than the oblique jet impingement in upstream two tiers.

Sign in / Sign up

Export Citation Format

Share Document