Analysis of Flangeability by Single-Stage SPIF and Press-Working in AA7075-O Sheet

2020 ◽  
pp. 1-17
Author(s):  
Marcos Borrego ◽  
Domingo Morales-Palma ◽  
Carpóforo Vallellano
Keyword(s):  
Deformation Process ◽  
Failure Modes ◽  
Forming Limit Diagram ◽  
Experimental Tests ◽  
Single Stage ◽  
Forming Limit ◽  
Flange Forming ◽  
Conventional Press ◽  
Forming Tools ◽  
Hole Flanging

Abstract Recently, the research interest of hole-flanging has turned from conventional press-working to SPIF as a viable process for small- and medium-sized batches. Both technologies have been studied separately using different approaches and, therefore, most studies cannot be easily compared. Besides, some studies that measured the formability in SPIF using the classical Limiting Forming Ratio (LFR) showed conflicting results that still need to be clarified. Under these circumstances, the aim of this work is to provide a better understanding of the deformation process and the material formability in hole-flanging by critically comparing both forming processes. To this end, a series of experimental tests on AA7075-O sheet of 1.6-mm thickness by press-working and single-stage SPIF, using forming tools with different profile radii, are analysed. The material formability and flange geometry are compared and discussed in detail. The process limits are analysed by using both the Forming Limit Diagram (FLD) and the LFR. The failure modes by necking and fracture are clearly identified and assessed on both processes along with the influence of the bending induced by the tools during the flange forming. Results conclude that the LFR is not an adequate parameter to compare formability between processes other than press-working and, accordingly, two additional variables based on either the flange height or the average thickness reduction are proposed to successfully analyse flangeability.

scholarly journals Revisiting flangeability in hole-flanging by single-stage incremental forming and conventional process

2021 ◽  
Author(s):  
Marcos Borrego ◽  
Domingo Morales-Palma ◽  
José Andrés Lopez-Fernandez ◽  
Andrés J. Martinez-Donaire ◽  
Gabriel Centeno ◽  
...  
Keyword(s):  
Incremental Forming ◽  
Stress Triaxiality ◽  
Single Stage ◽  
Forming Limit ◽  
Forming Process ◽  
Forming Limit Curve ◽  
Conventional Press ◽  
High Flexibility ◽  
Hole Flanging ◽  
Suitable Process

Recently, hole-flanging by single-stage incremental forming (SPIF) has been proposed as a suitable process to perform hole flanges for small- and medium-sized batches with high flexibility in shape. However, this incremental forming has many differences compared with the conventional press working operation in terms of strain and thickness distributions, failure mechanisms and flangeability measures. In fact, regarding the evaluation of the formability of the flanges, the classical Forming Limit Ratio (LFR) should be used with care to quantify this property in hole-flanging by SPIF. Additionally, the FLC (Forming Limit Curve for necking) and FFL (Fracture Forming Limit) curves, powerful tools for analysing sheet failure in practice, may also yield erroneous prediction of necking in conventional press working or fracture in SPIF. The aim of this work is to present a comparison and analysis of the formability of hole flanges performed by SPIF and press working in AA7075-O sheets. Two complementary parameters to the LFR to compare the flangebility in both operations are discussed, along with the influence of bending induced by the forming tool and the stress triaxiality in the evolution of the principal strains during the forming process. The results point out the limitations in the current practice.

Optimization of Tube Hydroforming Process Using Probabilistic Constraints on Failure Modes

2011 ◽  
Vol 62 ◽  
pp. 21-35 ◽  
Author(s):  
Anis Ben Abdessalem ◽  
A. El Hami
Keyword(s):  
Failure Modes ◽  
High Reliability ◽  
Thickness Distribution ◽  
Tube Hydroforming ◽  
Forming Limit Diagram ◽  
Plastic Instability ◽  
Probabilistic Constraints ◽  
Forming Limit ◽  
Reliability Based Design ◽  
Hydroforming Process

In metal forming processes, different parameters (Material constants, geometric dimensions, loads …) exhibits unavoidable scatter that lead the process unreliable and unstable. In this paper, we interest particularly in tube hydroforming process (THP). This process consists to apply an inner pressure combined to an axial displacement to manufacture the part. During the manufacturing phase, inappropriate choice of the loading paths can lead to failure. Deterministic approaches are unable to optimize the process with taking into account to the uncertainty. In this work, we introduce the Reliability-Based Design Optimization (RBDO) to optimize the process under probabilistic considerations to ensure a high reliability level and stability during the manufacturing phase and avoid the occurrence of such plastic instability. Taking account of the uncertainty offer to the process a high stability associated with a low probability of failure. The definition of the objective function and the probabilistic constraints takes advantages from the Forming Limit Diagram (FLD) and the Forming Limit Stress Diagram (FLSD) used as a failure criterion to detect the occurrence of wrinkling, severe thinning, and necking. A THP is then introduced as an example to illustrate the proposed approach. The results show the robustness and efficiency of RBDO to improve thickness distribution and minimize the risk of potential failure modes.

Experimental Determination of Anisotropic Properties and Evaluation of FLD for Sheet Metal Operations

2021 ◽  
Vol 106 ◽  
pp. 39-45
Author(s):  
Araveeti C. Sekhara Reddy ◽  
B. Sandeep ◽  
J. Sandeep Kumar ◽  
B. Sanjanna
Keyword(s):  
Deep Drawing ◽  
Grain Orientation ◽  
Forming Limit Diagram ◽  
Experimental Tests ◽  
Rolling Process ◽  
Forming Limit ◽  
Drawing Process ◽  
Sheet Metals ◽  
Deformation Models

Most of the sheet metals in general exhibit high an-isotropic plasticity behavior due to the ordered grain orientation that occurred during the rolling process. This results in an uneven deformation yield property that tends to develop ears in case of deep-drawing operation. The deep drawing process is used for the production of cup-shaped articles having applications in automobiles, beverages, home appliances etc. It is essential to know the formability of sheet metals for minimisation of test runs and reducingthe defects. Forming Limit Diagram (FLD) is one of the methods for assessment of formability of sheetmetals. This paper describes various deformation models, yielding and an-isotropic properties and itsdetermination. Through experimental tests, FLD constructed for aluminium alloy AA6111 sheet metalhaving 0.9 mm thickness.

scholarly journals PADDLE SHAPE OPTIMIZATION FOR HOLE-FLANGING BY PADDLE FORMING THROUGH THE USE OF A PREDEFINED STRAIN PATH IN FINITE ELEMENT ANALYSIS

2019 ◽  
Vol 19 (2) ◽  
pp. 83-98 ◽  
Author(s):  
Lemopi Isidore BESONG ◽  
Johannes BUHL ◽  
Markus BAMBACH
Keyword(s):  
Finite Element ◽  
Strain Path ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Element Analysis ◽  
High Speeds ◽  
The Right ◽  
Hole Flanging ◽  
Bulge Formation ◽  
Principal Strains

This research investigates a novel hole-flanging process by paddle forming through the use of finite element (FE) simulations. Paddles of different shapes rotating at high speeds were used to deform clamped sheets with pre-drilled holes at their centers. The results of the simulations show that the paddle shape determines the geometry and principal strains of the formed flanges. A convex-shaped paddle forms flanges with predominant strains in the left quadrant of the forming limit diagram (FLD). However, the convex paddle promotes unwanted bulge formation at the clamped end of the flange. A concave paddle forms flanges with no bulge but the principal strains of elements in the middle section of the flange are in the right quadrant of the FLD which indicates an increased probability for crack occurrence. An optimization of the paddle shape was conducted to prevent bulging at the clamped end while avoiding crack occurrence. The paddle shape was optimized by mapping the deformation of some elements along the flange length to a pre-defined strain path on the FLD while maintaining the bulge height within the desired geometric tolerance. The radii and lengths of the paddle edge were varied to obtain an optimum paddle shape.

Formability Analysis of AA6061 Sheet in T6 Condition

2015 ◽  
Vol 766-767 ◽  
pp. 416-421
Author(s):  
S. Vijayananth ◽  
V. Jayaseelan ◽  
G. Shivasubbramanian
Keyword(s):  
Experimental Method ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Ansys Software ◽  
Limit Curve ◽  
High Corrosion Resistance ◽  
Forming Limit Curve ◽  
Drawing Test ◽  
Deep Drawing Test ◽  
Alloy 6061

Formability of a material is defined as its ability to deform into desired shape without being fracture. There will always be a need for formability tests, a larger number of tests have been used in an effort to measure the formability of sheet materials. Aluminium Alloy 6061 is a magnesium and silicon alloy of aluminium. It is also called as marine material as it has high corrosion resistance to seawater. In this paper Formability test of AA6061 sheet is done by Forming Limit Diagram (FLD) Analysis. FLD or Forming Limit Curve (FLC) for the forming processes of AA6061 sheets is obtained by Experimental method and FEM. Experimental method involves Deep drawing test of the sheet and ANSYS software is used for FEM.

Optimization of Sheet Metal Process Parameters of a Shield Case Piece Using Computer Simulation

2006 ◽  
Vol 510-511 ◽  
pp. 330-333
Author(s):  
M.C. Curiel ◽  
Ho Sung Aum ◽  
Joaquín Lira-Olivares
Keyword(s):  
Sheet Metal ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Physical Processes ◽  
Forming Process ◽  
Element Analysis ◽  
One Step ◽  
Range Of Values ◽  
Principal Strains

Numerical simulations based on Finite Element Analysis (FEA) are widely used to predict and evaluate the forming parameters before performing the physical processes. In the sheet metal industry, there are basically two types of FE programs: the inverse (one-step) programs and the incremental programs. In the present paper, the forming process of the shield case piece (LTA260W1-L05) was optimized by performing simulations with both types of software. The main analyzed parameter was the blankholding force while the rest of the parameters were kept constant. The criteria used to determine the optimum value was based on the Forming Limit Diagram (FLD), fracture and wrinkling of the material, thickness distribution, and the principal strains obtained. It was found that the holding force during the forming process deeply affects the results, and a range of values was established in which the process is assumed to give a good quality piece.

Sign in / Sign up

Export Citation Format

Share Document