Experimental Investigations of Clocking in a One and a Half Stage Transonic Turbine Using Laser-Doppler-Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschla¨ger ◽  
A. Fuchs ◽  
E. Go¨ttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-Velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different 1st vane to 2nd vane positions (clocking positions) for measurements downstream of the 2nd vane row and two different clocking positions for measurements upstream of the 2nd vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the 2nd vane row. Furthermore different measurement lines upstream of the 2nd vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Experimental Investigations of Clocking in a One-and-a-Half-Stage Transonic Turbine Using Laser Doppler Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Vol 129 (2) ◽  
pp. 372-381 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
A. Fuchs ◽  
E. Göttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle, and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast-response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different first vane to second vane positions (clocking positions) for measurements downstream of the second vane row and two different clocking positions for measurements upstream of the second vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the second vane row. Furthermore, different measurement lines upstream of the second vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Three Dimensional Clocking Effects in a One and a Half Stage Transonic Turbine

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Velocity Flow ◽  
Transonic Turbine

This paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three-dimensional aerodynamics of the second vane for different clocking positions. To give an overview of the time-averaged flow field, five-hole probe measurements were performed upstream and downstream of the second stator. Furthermore in these planes additional unsteady measurements were carried out with laser Doppler velocimetry in order to record rotor phase-resolved velocity, flow angle, and turbulence distributions at two different clocking positions. In the planes upstream of the second vane, the time-resolved pressure field has been measured by means of a fast response aerodynamic pressure probe. This paper shows that the secondary flows of the second vane are significantly modified by the different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out, and a 0.6% variation in the second vane loss coefficient has been recorded among the different clocking positions.

Blade Row Interaction in a One and a Half Stage Transonic Turbine Focusing on Three Dimensional Effects: Part II—Clocking Effects

2008 ◽  
Author(s):  
O. Schennach ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani ◽  
J. Woisetschla¨ger
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Three Dimensional ◽  
Field Measurements ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three dimensional flow field downstream of the high pressure turbine for different vane clocking positions. To give an overview of the time averaged flow field, measurements by means of a pneumatic five hole probe were performed upstream and downstream of the second stator. Furthermore in this planes additional unsteady measurements were carried out with Laser Doppler Velocimetry in order to record rotor phase resolved velocity, flow angle and turbulence distributions at two different clocking positions. In the measurement plane upstream the second vane the time resolved pressure field has been analyzed by means of a Fast Response Aerodynamic Pressure Probe. The paper shows that the secondary flows of the second vane are significantly modified for different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out.

Experimental Investigation of the Unsteady Flow Field Downstream of a Counter-Rotating Two-Spool Turbine Rig

2012 ◽  
Author(s):  
Davide Lengani ◽  
Cornelia Santner ◽  
Rosario Spataro ◽  
Berardo Paradiso ◽  
Emil Göttlich
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Fast Response ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure

The paper presents an experimental investigation of the unsteady flow field in the two-spool counter-rotating transonic turbine at Graz University of Technology. The test setup consists of a high pressure (HP) stage, a diffusing mid turbine frame with turning struts (TMTF) and a shrouded low pressure (LP) rotor. The two rotors are mounted on mechanically independent shafts in order to provide engine-representative operating conditions. The rig was designed in cooperation with MTU Aero Engines and Volvo Aero within the EU project DREAM (ValiDation of Radical Engine Architecture SysteMs). A two-sensor fast response aerodynamic pressure probe (2S-FRAP) has been employed to provide time-resolved aerodynamic area traverses downstream of the LP turbine. Such measurement allows estimating the total deterministic unsteadiness transported through the duct. In particular, it has been possible to isolate the structures induced by each rotor by means of the encoders mounted on the two shafts. A global ensemble averaged field, which takes into account the rotor-rotor interactions, is also provided. The time resolved distributions of the flow quantities are then discussed in details. The perturbations due to the HP rotor in terms of velocity and flow angle are negligible in this downstream plane. Indeed, the largest fluctuations of velocity are due to the TMTF-LP rotor interaction, they occur in the wake and secondary flows of the TMTF. Large fluctuations of static and total pressure are instead due to both rotors to the same extent.

The Effect of Vane Clocking on the Unsteady Flowfield in a One and a Half Stage Transonic Turbine

2007 ◽  
Author(s):  
O. Schennach ◽  
R. Pecnik ◽  
B. Paradiso ◽  
E. Go¨ttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Laser Doppler Velocimetry ◽  
Three Dimensional ◽  
Fast Response ◽  
Navier Stokes ◽  
Doppler Velocimetry ◽  
Pressure Transducers ◽  
Wake Interactions ◽  
Transonic Turbine ◽  
Response Pressure ◽  
Vane Clocking

The current paper presents the results of numerical and experimental clocking investigations performed in a high-pressure transonic turbine with a downstream vane row. The objective was a detailed analysis of shock and wake interactions in such a 1.5 stage machine while clocking the vanes. Therefore a transient 3D-Navier Stokes calculation was done for two clocking positions and the three dimensional results are compared with Laser-Doppler-Velocimetry measurements at midspan. Additionally the second vane was equipped with fast response pressure transducers to record the instantaneous surface pressure for 20 different clocking positions at midspan.

Flow Field Measurements in a Metal Additively Manufactured Offset Strip Fin Array Using Laser Doppler Velocimetry

2020 ◽  
Author(s):  
David Saltzman ◽  
Stephen Lynch
Keyword(s):  
Surface Roughness ◽  
Heat Exchanger ◽  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Field Measurements ◽  
Laser Doppler ◽  
Doppler Velocimetry ◽  
Pressure Losses ◽  
Wide Range ◽  
Offset Strip Fin

Abstract Metal additive manufacturing (AM) of heat exchanger enables custom and conformal designs for a wide range of applications. However, one challenge with metal AM is the resultant surface roughness formed when using this process which is non-existent during traditional manufacturing processes. The goal in this study is to explore how this roughness impacts the pressure drop and flow field of a commonly used heat exchanger surface called an offset strip fin (OSF). Two OSF of the same geometry are tested: one with an average fin roughness of 34 µm from metal AM and the other with an average fin roughness 2.5 µm, used as a baseline. The roughness from the metal AM process increased pressure losses and transitioned the flow to turbulent-like behavior at lower Reynolds numbers when compared with the smooth fin. Laser Doppler Velocimetry (LDV) measurements captured the row number in the fin array where transition from laminar to turbulent-like flow occurred. The location of transition from low to high turbulence levels occurred earlier in the fin array as the Reynolds number was increased for the smooth and rough fins. Wake profiles of time-averaged axial velocity were similar between the rough and smooth fins, with the rough fins having higher levels of turbulence intensity and less symmetric wake profiles. Overall, this study indicates that a pressure loss penalty is associated with using metal AM OSF due to the resultant surface roughness and an earlier transition to turbulent-like flow.

Flow Field Investigation in a Low-Solidity Inducer by Laser-Doppler Velocimetry

1990 ◽  
Vol 112 (1) ◽  
pp. 91-97 ◽  
Author(s):  
A. Boccazzi ◽  
A. Perdichizzi ◽  
U. Tabacco
Keyword(s):  
Flow Field ◽  
Flow Rate ◽  
Reverse Flow ◽  
Field Investigation ◽  
Design Flow ◽  
Laser Doppler ◽  
Laser Doppler Velocimeter ◽  
Pressure Probe ◽  
Specific Work ◽  
Flow Angle

The results of an experimental investigation of the flow field within a low-solidity inducer at design and off-design flow rates are presented and discussed; particular attention is devoted to the analysis of the flow field, at the tip in front of the leading edge, for the flow rate close to the back-flow onset. The flow field was measured by means of a laser-Doppler velocimeter at four different axial positions upstream, within, and downstream of the inducer. Axial, tangential, and relative flow angle distributions, in the measuring planes, are presented for three different flow coefficients. At the lower flow rate, the plots show the presence of reverse flow in the region close to the hub downstream of the trailing edge. For the same flow rate, quite low axial velocities are detected at the tip. This is in agreement with pressure probe traverses carried out in a slightly downstream section; these measurements also show radial inward velocities of the same order of magnitude as the axial velocities. Circumferentially averaged losses were evaluated from specific work and total head rise given by pressure probes.

Sign in / Sign up

Export Citation Format

Share Document