Experimental Investigation of the Unsteady Flow Field Downstream of a Counter-Rotating Two-Spool Turbine Rig

2012 ◽  
Author(s):  
Davide Lengani ◽  
Cornelia Santner ◽  
Rosario Spataro ◽  
Berardo Paradiso ◽  
Emil Göttlich
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Fast Response ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure

The paper presents an experimental investigation of the unsteady flow field in the two-spool counter-rotating transonic turbine at Graz University of Technology. The test setup consists of a high pressure (HP) stage, a diffusing mid turbine frame with turning struts (TMTF) and a shrouded low pressure (LP) rotor. The two rotors are mounted on mechanically independent shafts in order to provide engine-representative operating conditions. The rig was designed in cooperation with MTU Aero Engines and Volvo Aero within the EU project DREAM (ValiDation of Radical Engine Architecture SysteMs). A two-sensor fast response aerodynamic pressure probe (2S-FRAP) has been employed to provide time-resolved aerodynamic area traverses downstream of the LP turbine. Such measurement allows estimating the total deterministic unsteadiness transported through the duct. In particular, it has been possible to isolate the structures induced by each rotor by means of the encoders mounted on the two shafts. A global ensemble averaged field, which takes into account the rotor-rotor interactions, is also provided. The time resolved distributions of the flow quantities are then discussed in details. The perturbations due to the HP rotor in terms of velocity and flow angle are negligible in this downstream plane. Indeed, the largest fluctuations of velocity are due to the TMTF-LP rotor interaction, they occur in the wake and secondary flows of the TMTF. Large fluctuations of static and total pressure are instead due to both rotors to the same extent.

Three Dimensional Clocking Effects in a One and a Half Stage Transonic Turbine

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Velocity Flow ◽  
Transonic Turbine

This paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three-dimensional aerodynamics of the second vane for different clocking positions. To give an overview of the time-averaged flow field, five-hole probe measurements were performed upstream and downstream of the second stator. Furthermore in these planes additional unsteady measurements were carried out with laser Doppler velocimetry in order to record rotor phase-resolved velocity, flow angle, and turbulence distributions at two different clocking positions. In the planes upstream of the second vane, the time-resolved pressure field has been measured by means of a fast response aerodynamic pressure probe. This paper shows that the secondary flows of the second vane are significantly modified by the different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out, and a 0.6% variation in the second vane loss coefficient has been recorded among the different clocking positions.

Blade Row Interaction in a One and a Half Stage Transonic Turbine Focusing on Three Dimensional Effects: Part II—Clocking Effects

2008 ◽  
Author(s):  
O. Schennach ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani ◽  
J. Woisetschla¨ger
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Three Dimensional ◽  
Field Measurements ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three dimensional flow field downstream of the high pressure turbine for different vane clocking positions. To give an overview of the time averaged flow field, measurements by means of a pneumatic five hole probe were performed upstream and downstream of the second stator. Furthermore in this planes additional unsteady measurements were carried out with Laser Doppler Velocimetry in order to record rotor phase resolved velocity, flow angle and turbulence distributions at two different clocking positions. In the measurement plane upstream the second vane the time resolved pressure field has been analyzed by means of a Fast Response Aerodynamic Pressure Probe. The paper shows that the secondary flows of the second vane are significantly modified for different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out.

Time-Resolved Measurements of the Unsteady Flow Field in a Single Stage Low Pressure Axial Compressor

2013 ◽  
Author(s):  
J. Sans ◽  
G. Dell’Era ◽  
J. Desset ◽  
J.-F. Brouckaert ◽  
S. Hiernaux
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Low Pressure ◽  
Fast Response ◽  
Single Stage ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Time Resolved Measurements

The experimental investigation of the unsteady flow field in a highly loaded single stage low pressure axial compressor, also called a booster, is presented in this paper. The compressor design is representative of an advanced direct drive turbofan booster. Tests were performed on different speed lines at choke, design, and near stall, in the VKI-R4 closed loop compressor test rig. The rotor casing was instrumented with fast response pressure transducers to perform a detailed survey of the tip flow features. Simultaneous time-resolved measurements with fast response aerodynamic pressure probes were performed by radial and circumferential traverses to map the unsteady flow field at rotor and stator exit. The originality of this paper also resides in the fact that unsteady flow angle data are presented as the probe was used in a virtual 3-hole mode. The casing measurements allow to map the direction and extension of the tip leakage vortex. The flow path measurements show its extension at the exit of the rotor blade passage and its evolution as throttling is increased towards the compressor stability limit. The results are presented in terms of periodic and random fluctuations. These experimental results are combined to provide a three-dimensional view of the experimental flow field. They are discussed and compared to CFD simulations, showing that, in some regions, important features are not captured by the numerical model. In particular, the presence of a second wake has been observed in the unsteady yaw angle map at rotor exit. This uncommon feature is currently under further investigation.

Effects of Off-Design Operating Conditions on the Blade Row Interaction in a HP Turbine Stage

2007 ◽  
Author(s):  
G. Persico ◽  
P. Gaetani ◽  
C. Osnaghi
Keyword(s):  
Flow Field ◽  
Strong Dependence ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Turbine Stage ◽  
Mixing Rate ◽  
Aerodynamic Pressure ◽  
Blade Row ◽  
Blade Row Interaction

An extensive experimental analysis on the subject of the unsteady periodic flow in a highly subsonic HP turbine stage has been carried out at the Laboratorio di Fluidodinamica delle Macchine (LFM) of the Politecnico di Milano (Italy). In this paper the blade row interaction is progressively enforced by increasing the stator and rotor blade loading and by reducing the stator-rotor axial gap from 100% (very large to smooth the rotor inlet unsteadiness) to 35% (design configuration) of the stator axial chord. The time-averaged three-dimensional flow field in the stator-rotor gap was investigated by means of a conventional five-hole probe for the nominal (0°) and an highly positive (+22°) stator incidences. The evolution of the viscous flow structures downstream of the stator is presented to characterize the rotor incoming flow. The blade row interaction was evaluated on the basis of unsteady aerodynamic measurements at the rotor exit, performed with a fast-response aerodynamic pressure probe. Results show a strong dependence of the time-averaged and phase-resolved flow field and of the stage performance on the stator incidence. The structure of the vortex-blade interaction changes significantly as the magnitude of the rotor inlet vortices increases, and very different residual traces of the stator secondary flows are found downstream of the rotor. On the contrary, the increase of rotor loading enhances the unsteadiness in the rotor secondary flows but has a little effect on the vortex-vortex interaction. For the large axial gap, a reduction of stator-related effects at the rotor exit is encountered when the stator incidence is increased as a result of the different mixing rate within the cascade gap.

Experimental Investigations of Clocking in a One and a Half Stage Transonic Turbine Using Laser-Doppler-Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschla¨ger ◽  
A. Fuchs ◽  
E. Go¨ttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-Velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different 1st vane to 2nd vane positions (clocking positions) for measurements downstream of the 2nd vane row and two different clocking positions for measurements upstream of the 2nd vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the 2nd vane row. Furthermore different measurement lines upstream of the 2nd vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Identification of Spinning Mode in the Unsteady Flow Field of a LP Turbine

2011 ◽  
Author(s):  
Davide Lengani ◽  
Berardo Paradiso ◽  
Andreas Marn ◽  
Emil Go¨ttlich
Keyword(s):  
Flow Field ◽  
Guide Vane ◽  
Fast Response ◽  
Turbine Rotor ◽  
Pressure Probe ◽  
Model Parameters ◽  
Time Resolved ◽  
Flow Angle ◽  
Response Pressure ◽  
Lp Turbine

This paper presents an experimental investigation of the vane-blade unsteady interaction in an unshrouded LP turbine research rig with uneven blade/vane count (72 blades and 96 vanes). The rig was designed in cooperation with MTU Aero Engines and considerable efforts were put on the adjustment of all relevant model parameters. In particular blade count ratio, airfoil aspect ratio, reduced massflow, reduced speed, Mach and Reynolds numbers were chosen to reproduce the full scale LP turbine at take off condition. Measurements by means of a fast-response pressure probe were performed adopting a phase-locked acquisition technique in order to provide the time resolved flow field downstream of the turbine rotor. The probe has been fully traversed both in circumferential and radial traverses. The rotor exit is characterized by strong perturbations due to the tip leakage vortex and the rotor blade wake. Circumferential non uniformities due to the upstream vane wake and to the downstream exit guide vane potential effects are also identified. Furthermore in the present configuration with an uneven blade/vane count the non-uniformities due to the stator and rotor row are misaligned along the whole turbine circumference and create a spinning mode that rotates in direction opposite to the rotor at a high frequency. The aeroacoustic theory is employed to explain such further unsteady pattern. The variations of the exit flow angle within a cycle of such pattern are not negligible and almost comparable to the ones within the blade passing period.

Identification of Spinning Mode in the Unsteady Flow Field of a Low Pressure Turbine

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Davide Lengani ◽  
Berardo Paradiso ◽  
Andreas Marn ◽  
Emil Göttlich
Keyword(s):  
Flow Field ◽  
Guide Vane ◽  
Low Pressure ◽  
Fast Response ◽  
Turbine Rotor ◽  
Pressure Probe ◽  
Model Parameters ◽  
Time Resolved ◽  
Flow Angle ◽  
Lp Turbine

This paper presents an experimental investigation of the vane-blade unsteady interaction in an unshrouded low pressure (LP) turbine research rig with uneven blade/vane count (72 blades and 96 vanes). The rig was designed in cooperation with MTU Aero Engines and considerable efforts were put on the adjustment of all relevant model parameters. In particular blade count ratio, airfoil aspect ratio, reduced mass flow, reduced speed, and Mach and Reynolds numbers were chosen to reproduce the full scale LP turbine at take off condition. Measurements by means of a fast-response pressure probe were performed adopting a phase-locked acquisition technique in order to provide the time resolved flow field downstream of the turbine rotor. The probe has been fully traversed both in circumferential and radial traverses. The rotor exit is characterized by strong perturbations due to the tip leakage vortex and the rotor blade wake. Circumferential nonuniformities due to the upstream vane wake and to the downstream exit guide vane potential effects are also identified. Furthermore, in the present configuration with an uneven blade/vane count the nonuniformities due to the stator and rotor row are misaligned along the whole turbine circumference and create a spinning mode that rotates in direction opposite to the rotor at a high frequency. The aeroacoustic theory is employed to explain such further unsteady pattern. The variations of the exit flow angle within a cycle of such pattern are not negligible and almost comparable to the ones within the blade passing period.

Unsteady Flow Interactions Between a High- and Low-Pressure Turbine: Part 2 — Rotor-Synchronic Averaging and Proper Orthogonal Decomposition of the Unsteady Flow Fields

2019 ◽  
Author(s):  
M. Dellacasagrande ◽  
P. Z. Sterzinger ◽  
S. Zerobin ◽  
F. Merli ◽  
L. Wiesinger ◽  
...  
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Proper Orthogonal Decomposition ◽  
Low Pressure ◽  
Fast Response ◽  
Orthogonal Decomposition ◽  
Pressure Probe ◽  
Low Pressure Turbine ◽  
Aerodynamic Pressure ◽  
Proper Orthogonal

Abstract This paper, the second of two parts, presents an experimental investigation of the unsteady flow field evolving in a two-stage two-spool test turbine facility. The experimental setup, which was designed to reproduce the operating condition of modern commercial aero-engines, consists of a high-pressure turbine (HPT) stage followed by a turbine center frame (TCF) with non-turning struts, and a co-rotating low-pressure turbine (LPT) stage. Measurements carried out with a fast-response aerodynamic pressure probe (FRAPP) were post-processed to describe the unsteady evolution of the flow downstream of the HPT rotor, through the TCF duct, and at the exit of the LPT stage. The time-resolved results presented in the first part of this paper show that deterministic fluctuations due to both rotors characterize the flow field downstream of the LPT. In order to characterize the deterministic unsteadiness induced by all the components constituting the turbine facility (HPT, TCF and LPT) and their interactions, measurements were carried out in three different planes located downstream of the HPT, at the exit of the TCF and downstream of the LPT stage. The unsteady results obtained in the plane located at the exit of the LPT are discussed in more details in this second part of this paper, providing information about the interactions between the two rotors. A proper phase-average procedure, known as rotor synchronic averaging (RSA), which takes into account the rotorrotor interaction, was adopted to capture the unsteadiness due to both rotors. Proper Orthogonal Decomposition (POD) was also applied to provide a characterization of the major contributors in terms of energy to the deterministic unsteadiness occurring in the test turbine facility. At the exit of the LPT rotor, the perturbations induced by the HPT stage and the interactions between the two rotors were found to dominate over the unsteadiness due to the LPT only.

On the Influence of an Acoustically Optimized Turbine Exit Casing Onto the Unsteady Flow Field Downstream of a Low Pressure Turbine Rotor

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Loris Simonassi ◽  
Manuel Zenz ◽  
Stefan Zerobin ◽  
Thorsten Selic ◽  
Franz Heitmeir ◽  
...  
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
High Efficiency ◽  
Low Pressure ◽  
Low Noise ◽  
Secondary Flows ◽  
Test Facility ◽  
Pressure Probe ◽  
Guide Vanes ◽  
Aerodynamic Pressure

Modern low pressure turbines (LPT) are designed in order to fulfil a various number of requirements such as high endurance, low noise, high efficiency, low weight, and low fuel consumption. Regarding the reduction of the emitted noise, different designs of LPT exit guide vanes (aerodynamically and/or acoustically optimized) of the turbine exit casing (TEC) were tested, and their noise reduction capabilities and aerodynamic performance were evaluated. In particular, measurements of TEC-losses were performed, and differences in the losses were reported. Measurements were carried out in a one and a half stage subsonic turbine test facility at the engine relevant operating point approach. This work focuses on the study of the unsteady flow field downstream of an unshrouded LPT rotor. The influence on the upstream flow field of a TEC design including acoustically optimized vanes (inverse cut-off TEC) is investigated and compared with a second TEC configuration without vanes (Vaneless TEC), by means of fast response aerodynamic pressure probe (FRAPP) measurements. The second configuration served as a reference concerning the influence of turbine exit guide vanes (TEGVs) onto the upstream located LPT rotor. The interactions between the stator and rotor wakes, secondary flows, and the TEGVs potential effect are identified via modal decomposition according to the theory of Tyler and Sofrin. The main structures constituting the unsteady flow field are detected, and the role of the major interaction effects in the loss generation mechanism and in the acoustic emission is analyzed. This study based on the modal analysis of the unsteady flow field offers new insight into the main interaction mechanisms and their importance in the assessment of the aerodynamic and aeroelastic performance of modern LPT exit casings.

Experimental Investigations of Clocking in a One-and-a-Half-Stage Transonic Turbine Using Laser Doppler Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Vol 129 (2) ◽  
pp. 372-381 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
A. Fuchs ◽  
E. Göttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle, and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast-response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different first vane to second vane positions (clocking positions) for measurements downstream of the second vane row and two different clocking positions for measurements upstream of the second vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the second vane row. Furthermore, different measurement lines upstream of the second vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Sign in / Sign up

Export Citation Format

Share Document