Study on the Rod Drop Performance of High-Temperature Gas-Cooled Reactor

2014 ◽  
Author(s):  
He Yan ◽  
Xingzhong Diao
Keyword(s):  
High Temperature ◽  
Pressure Vessel ◽  
Reactor Core ◽  
Insertion Time ◽  
Operational Mode ◽  
Control Rod ◽  
Rod System ◽  
Key Factor ◽  
Control Rods ◽  
High Temperature Gas

In this paper, the theoretical study and experimental investigation on the rod drop performance of high-temperature gas-cooled reactor (HTGR) pebble-bed module have been presented. The control rod drive mechanisms (CRDMs), serving as the first shutdown system of the reactor, are positioned above the reactor pressure vessel. When the reactor is operated at the power regulation mode, the control rods are pulled up-and-down in their channels around the reactor core. The CRDM provides a fail-safe operational mode for the control rod system. If the reactor emergency shutdown is required the control rods could drop into their channels by gravity. Thus the key factor, emergency insertion time of the whole control rod stroke, which represents the inherent safety of the CRDM, is crucially important and should be measured precisely. In the final objective of ensuring reliability of the CRDM, a full size drive line had been built and tested to obtain the overall performance function of the CRDM. Every component of the CRDM test line was simulated at the scale 1:1, including a 15 meters high test bench that was used as the substitution of the pressure vessel. At current stage, the rod drop performance had been experimental investigated at ambient temperature and pressure. The emergency insertion time of an 8 meters stroke was measured to be less than 50 seconds. A mathematical model of CRDM also had been developed. The rod motion characteristic equations show that the rod dropping speed approaches to a constant during the emergency insertion. The theoretical results are in agreement with the test results.

scholarly journals Bypass flow in small absorber sphere channels of the high-temperature gas-cooled reactor pebble-bed module

2017 ◽  
Vol 10 (3) ◽  
pp. 128-139 ◽  
Author(s):  
Ziping Liu ◽  
Zeguang Li ◽  
Jun Sun
Keyword(s):  
High Temperature ◽  
Network Model ◽  
Reactor Core ◽  
Flow Distribution ◽  
Maximum Temperature ◽  
Bypass Flow ◽  
Pebble Bed ◽  
Flow Network ◽  
Control Rod ◽  
High Temperature Gas

In the high-temperature gas-cooled reactor pebble-bed module, the helium bypass flow among graphite blocks cannot be ignored due to its effect on the temperature distribution as well as the maximum temperature in the reactor core. Bypass flow was previously analyzed in the discharging tube, in vertical gaps between graphite reflectors, and in control rod channels. The focus of this study is on the bypass flow that connects the small absorber sphere channels. Different from bypass flow connecting the control rod channels, there was no evident inlet or outlet flow paths into or out of the small absorber sphere channels at the top or bottom of the reactor core. Therefore, the bypass flow connecting the pebble bed with the small absorber sphere channels was mainly caused by the horizontal gaps, in which those gaps would also be irregular due to installation, thermal expansion, or irradiation of the graphite reflectors. After clarifying the resistant coefficients of those gaps by computational fluid dynamic tools, the bypass flow distribution was calculated by the flow network model including the flow in the reactor core, small absorber sphere channels, as well as horizontal gaps. Cases with various size combinations of gaps were adopted into the flow network model to test the sensitivity of bypass flow distribution to those parameters. Finally, the bypass flow in the small absorber sphere channels was concluded to be not significant in the reactor core.

scholarly journals ANALISIS PENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM

2016 ◽  
Vol 19 (2) ◽  
pp. 75
Author(s):  
Syarip, Khoirul Anam, Dwi Priyantoro
Keyword(s):  
High Temperature ◽  
Power Reactor ◽  
Operation Time ◽  
Reactor Power ◽  
Fuel Temperature ◽  
Reactor Operation ◽  
Control Rod ◽  
Negative Reactivity ◽  
Control Rods ◽  
High Temperature Gas

ANALISISPENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM POST REACTOR SCRAM CONTROL RODS POSITION ADJUSTMENT ANALYSIS FOR THE INDONESIAN EXPERIMENTAL POWER REACTOR CONCEPT. ABSTRAK ANALISIS PENGATURAN POSISI CONTROL RODS PADA KONSEP REAKTOR DAYA EKSPERIMENTAL INDONESIA PASCA REACTOR SCRAM. Telah dilakukan analisis simulasi pengaturan posisi batang-batang kendali untuk melanjutkan operasi reaktor daya eksperimental (RDE) paska scram setelah beroperasi pada periode waktu tertentu. Pengendalian reaktivitas pada reaktor RDE yang akan dibangun di Indonesia dengan rujukan high temperature gas reactor (HTR) 10 MWt, dilakukan dengan 10  pasang batang-batang kendali atau control rod (CR). Apabila terrjadi kondisi abnormal maka CR secara otomatis akan jatuh tersisip ke dalam reflektor  reaktor sehingga reaktor scram dan berada pada kondisi subkritis. Untuk melanjutkan operasi reaktor pasca scram diperlukan analisis terkait pengaruh reaktivitas negatif dari Xenon dan suhu. Pada makalah ini disajikan hasil simulasi yang dilakukan untuk penentuan posisi CR paling optimum untuk melanjutkan operasi reaktor, menggunakan simulator PCTRAN-HTR. Simulasi dilakukan pada variasi 70%, 85% dan 100% dari tingkat daya penuh dan dengan variasi waktu operasi 50 s, 10.000 s, dan 20.000 s di mana setelah reaktor beroperasi pada tingkat-tingkat daya dan waktu operasi tersebut reaktor mengalami scram. Untuk melanjutkan operasi lagi maka CR harus dinaikkan lagi dan diatur ke posisi tertentu sampai   reaktor mencapai kondisi kritis lagi pada tingkat daya nominal tersebut. Hasil yang telah diperoleh menunjukkan bahwa dengan posisi CR naik 52 % sudah bisa menghasilkan kondisi kritis dan mampu mengatasi reaktivitas negatif peracunan xenon maupun suhu. Kata kunci: RDE, HTR, operasi reaktor, batang kendali, reaktivitas, scram ABSTRACT POST REACTOR SCRAM CONTROL RODS POSITION ADJUSTMENT ANALYSIS FOR THE INDONESIAN EXPERIMENTAL POWER REACTOR CONCEPT. Analytical study using PC-based simulator has been carried out on control rods position adjustment of the Indonesian experimental power reactor concept or reaktor daya ekperimental (RDE) in a post reactor scram to continue operation after a certain operation period. Reactivity control of the RDE uses 10 pairs of control rods (CRs), which is based on that applied in the high temperature gas reactor (HTR) 10 MW(t). If an abnormal operating condition occurs, these control rods automatically dropped to the reflector that bring the reactor into a scram and subcritical condition. To continue reactor operation after a period of time, the CRs should be withdrawn to achieve recriticality. Prior to any CRs withdrawal, an analysis of negative reactivity effects of Xenon (poissoning) and fuel temperature coefficient should be done. Simulations using PCTRAN-HTR simulator to determine the optimum CRs positions in achieving reactor criticality for continuation of reactor operation is presented in this paper. The simulations were conducted by varying the reactor power levels at 70%, 85% and 100% of full power, respectively. The reactor operation time was varied at 50s, 10000s, and 20000 s prior to the reactor scram. Adjustment of CRs position should be done to continue reactor operation at those nominal power levels by withdrawing the CRs to the proper positions. The simulation results show that recriticality can be achieverd by whitdrawing the CRs 52% of farther and the negative reactivity from xenon poisoning and temperature could be overcome. Keywords : RDE, HTR, reactor operation, control rod, reactivity, scram.

Reactivity Accident Due to Control Rod Inadvertent Withdrawal of the 250MW High Temperature Gas-Cooled Reactor

2010 ◽  
Author(s):  
Yanhua Zheng ◽  
Lei Shi
Keyword(s):  
High Temperature ◽  
Reactor Core ◽  
Fission Products ◽  
Reactor Power ◽  
Fuel Temperature ◽  
Control Rod ◽  
Detail Design ◽  
Fuel Particles ◽  
Reactivity Accident ◽  
High Temperature Gas

Reactivity accident due to inadvertent withdrawal of the control rod is one kind of the design basis accident for high temperature gas-cooled reactors, which should be analyzed carefully in order to validate the reactor inherent safety properties. Based on the preliminary design of the Chinese Pebble-bed Modular High Temperature Gas-cooled Reactor (HTR-PM) with single module power of 250MW, several cases of reactivity accident has been studied by the help of the software TINTE in the paper, e.g., the first scram signal works or not, the absorber balls (secondary shutdown units) drop or not, and the ATWS situation is also taken into account. The dynamic processes of the important parameters including reactor power, fuel temperature and Xenon concentration are studied and compared in detail between these different cases. The calculating results show that, the decay heat during the reactivity accidents can be removed from the reactor core solely by means of physical processes in a passive way, so that the temperature limits of fuel element and other components are still obeyed, which can effectively keep the integrality of the fuel particles to avoid massive fission products release. This will be helpful to the further detail design of the HTR-PM demonstrating power plant project.

Reactivity Accident in a High Temperature Gas-Cooled Reactor Due to Inadvertent Withdrawal of Control Rod

2010 ◽  
Vol 133 (5) ◽  
Author(s):  
Zheng Yanhua ◽  
Shi Lei
Keyword(s):  
High Temperature ◽  
Reactor Core ◽  
Fission Products ◽  
Reactor Power ◽  
Fuel Temperature ◽  
Control Rod ◽  
Detail Design ◽  
Fuel Particles ◽  
Reactivity Accident ◽  
High Temperature Gas

Reactivity accident due to inadvertent withdrawal of the control rod is one kind of the design basis accident for high temperature gas-cooled reactors, which should be analyzed carefully in order to validate the reactor inherent safety properties. Based on the preliminary design of the Chinese pebble-bed modular high temperature gas-cooled reactor (HTR-PM) with single module power of 250 MW, several cases of reactivity accident has been studied by the help of the software TINTE in the paper (e.g., the first scram signal works or not, the absorber balls (secondary shutdown units) drop or not) and the ATWS situation is also taken into account. The dynamic processes of the important parameters including reactor power, fuel temperature, and xenon concentration are studied and compared in detail between these different cases. The calculating results show that the decay heat during the reactivity accidents can be removed from the reactor core solely by means of physical processes in a passive way so that the temperature limits of the fuel element and other components are still obeyed, which can effectively keep the integrality of the fuel particles to avoid massive fission products release. This will be helpful to the further detail design of the HTR-PM demonstrating power plant project.

Calculation on the Distribution of Ex-Core Neutron Flux during Reactor Start-Up

2014 ◽  
Vol 672-674 ◽  
pp. 375-378
Author(s):  
Chun Yu Liu ◽  
Benbicha Mohamed Elghazali
Keyword(s):  
Neutron Flux ◽  
Physical Model ◽  
Pressure Vessel ◽  
Reactor Core ◽  
Mcnp Code ◽  
Control Rod ◽  
Start Up ◽  
Control Rods ◽  
Moving Process ◽  
Detection Effect

The distribution of neutron flux is simulated by MCNP code from reactor start-up to criticality when the control rods are drawn different length from reactor core on ex-core detector area of the WWER reactor of TianWan. Because physical model built is very large, in order to save calculation time, the moving process of control rod is simplified. The results of calculation show that The neutron mainly distributed in the range of 0-400cm outside the pressure vessel. The value of the relative neutron flux ex-core is maximum in the range of 110cm to 180cm, so detection effect is better when the detector is set in this region.

Thermal Modeling of the HTR-10 Using the RELAP5-3D Code

2014 ◽  
Author(s):  
Maria Elizabeth Scari ◽  
Antonella Lombardi Costa ◽  
Claubia Pereira ◽  
Clarysson Alberto Mello da Silva ◽  
Maria Auxiliadora Fortini Veloso
Keyword(s):  
High Temperature ◽  
Reactor Core ◽  
Initial Study ◽  
Industrial Applications ◽  
Pebble Bed ◽  
State Behavior ◽  
Energy Agency ◽  
Helium Gas ◽  
New Energy ◽  
High Temperature Gas

Several efforts have been considered in the development of the modular High Temperature Gas cooled Reactor (HTGR) planned to be a safe and efficient nuclear energy source for the production of electricity and industrial applications. In this work, the RELAP5-3D thermal hydraulic code was used to simulate the steady state behavior of the 10 MW pebble bed high temperature gas cooled reactor (HTR-10), designed, constructed and operated by the Institute of Nuclear and New Energy Technology (INET), in China. The reactor core is cooled by helium gas. In the simulation, results of temperature distribution within the pebble bed, inlet and outlet coolant temperatures, coolant mass flow, and others parameters have been compared with the data available in a benchmark document published by the International Atomic Energy Agency (IAEA) in 2013. This initial study demonstrates that the RELAP5-3D model is capable to reproduce the thermal behavior of the HTR-10.

A Nodal Dynamic Model for Control System Simulation of the HTR-PM Reactor Core

2010 ◽  
Author(s):  
Zhe Dong ◽  
Xiaojin Huang ◽  
Liangju Zhang
Keyword(s):  
Control System ◽  
High Temperature ◽  
Power Distribution ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Pebble Bed ◽  
Nodal Model ◽  
High Temperature Gas

The modular high-temperature gas-cooled nuclear reactor (MHTGR) is seen as one of the best candidates for the next generation of nuclear power plants. China began to research the MHTGR technology at the end of the 1970s, and a 10 MWth pebble-bed high temperature reactor HTR-10 has been built. On the basis of the design and operation of the HTR-10, the high temperature gas-cooled reactor pebble-bed module (HTR-PM) project is proposed. One of the main differences between the HTR-PM and HTR-10 is that the ratio of height to diameter corresponding to the core of the HTR-PM is much larger than that of the HTR-10. Therefore it is not proper to use the point kinetics based model for control system design and verification. Motivated by this, a nodal neutron kinetics model for the HTR-PM is derived, and the corresponding nodal thermal-hydraulic model is also established. This newly developed nodal model can reflect not only the total or average information but also the distribution information such as the power distribution as well. Numerical simulation results show that the static precision of the new core model is satisfactory, and the trend of the transient responses is consistent with physical rules.

scholarly journals Numerical modelling of modular high-temperature gas-cooled reactors with thorium fuel

Nukleonika ◽  
2021 ◽  
Vol 66 (4) ◽  
pp. 133-138
Author(s):  
Mikołaj Oettingen ◽  
Jerzy Cetnar
Keyword(s):  
High Temperature ◽  
Neutron Transport ◽  
Reactor Core ◽  
Computation Time ◽  
Homogenization Method ◽  
Uranium Fuel ◽  
Neutron Multiplication ◽  
3D Numerical Model ◽  
Effective Neutron ◽  
High Temperature Gas

Abstract The volumetric homogenization method for the simplified modelling of modular high-temperature gas-cooled reactor core with thorium-uranium fuel is presented in the paper. The method significantly reduces the complexity of the 3D numerical model. Hence, the computation time associated with the time-consuming Monte Carlo modelling of neutron transport is considerably reduced. Example results comprise the time evolutions of the effective neutron multiplication factor and fissionable isotopes (233U, 235U, 239Pu, 241Pu) for a few configurations of the initial reactor core.

Sign in / Sign up

Export Citation Format

Share Document