Development of Simplified Wear Estimation Method Considering Rolling Motion Between Mooring Chain Links for Floating Structures

2021 ◽  
Author(s):  
Takaaki Takeuchi ◽  
Tomoaki Utsunomiya ◽  
Koji Gotoh ◽  
Iku Sato
Keyword(s):  
Estimation Method ◽  
Irregular Waves ◽  
Rolling Motion ◽  
Spring Model ◽  
Floating Offshore Wind Turbines ◽  
Mass Spring Model ◽  
Link Model ◽  
Mass Spring ◽  
Chain Links ◽  
Mooring Chain

Abstract For the development of floating offshore wind turbines (FOWTs) in Japan, reliability assessment and cost reduction by efficient maintenance on mooring chains are part of the key issues because sites deeper than 60 m require mooring systems for station keeping. In this paper, attempts have been made to simplify the wear estimation method which was previously proposed by using a 3-D rigid-body link model for improvement of accuracy. These investigations are performed about a spar-type floating structure moored with three catenary lines at Goto, Nagasaki prefecture, Japan. In the previous study, it was confirmed that the estimation method using the 3-D link model can calculate the interlink wear amount closer to the chain diameter measurements and more reasonable than the method using the conventional mass-spring model by removing the rolling distance from the displacement of contact points. However, the estimation method has technical difficulty in terms of calculation of contact properties and analysis costs for the mooring chain design. For this reason, the wear estimation method is simplified and verified by considering the rolling motion between mooring chain links modeled by the widely employed mass-spring model based on the method proposed by Mooring Integrity JIP. Firstly, the wear due to the rolling is reproduced by a three-dimensional FE analysis to investigate the actual wear phenomenon including the effect of the proof load test as well as the idealized configuration. Secondly, the application method is proposed against the response of the mooring chain subjected to irregular waves Finally, a comparison with the measurement is conducted to verify the proposed wear estimation method.

Quantitative Wear Estimation for Floating Structures by Using 3-D Geometry of Mooring Chain

2020 ◽  
Author(s):  
Takaaki Takeuchi ◽  
Tomoaki Utsunomiya ◽  
Koji Gotoh ◽  
Iku Sato
Keyword(s):  
Estimation Method ◽  
Maintenance Cost ◽  
Offshore Wind Turbine ◽  
Response Analysis ◽  
Chain Model ◽  
Contact Method ◽  
Spring Model ◽  
Mass Spring Model ◽  
Mass Spring ◽  
Mooring Chain

Abstract For reducing the maintenance cost of floating offshore wind turbine structures, it is necessary to establish a quantitative wear estimation method for the mooring chains. In this paper, attempts have been made to improve the accuracy of the estimation method in terms of the mooring chain model. These investigations were performed about a spar-type floater moored with three catenary mooring lines at Goto, Nagasaki prefecture, Japan. Up to now, the mass-spring model had been used for the mooring chain in response analysis and the relative angle between two spring lines was considered as only a sliding angle without friction. However, there is also rolling in the motion between mooring links, which should cause less wear than by sliding. In this study, the detailed motion of the link in response analysis is calculated and applied to the wear estimation by using a 3-D model in MSC. Adams. This enables the wear estimation considering link motion closer to a real phenomenon. A Contact analysis between the 3-D chain model requires some contact properties (e.g. contact stiffness and friction). In this paper, these properties are calculated based on the Hertzian contact method and FEM analysis. As a result, the wear amounts overestimated by using the mass-spring model in the previous investigation, especially at the point located clump weight and touchdown point, decrease getting closer to the measurements. In addition, by tracking the contact points it is found that the major motion caused between links is the rolling. For future works, there remains a need for further validation and the consideration of elasticity between mooring links, impressions caused by proof load test and the effect of corrosion.

scholarly journals Review on the 3-D simulation for weft knitted fabric

2021 ◽  
Vol 16 ◽  
pp. 155892502110125
Author(s):  
Sha Sha ◽  
Anqi Geng ◽  
Yuqin Gao ◽  
Bin Li ◽  
Xuewei Jiang ◽  
...  
Keyword(s):  
Physical Models ◽  
Spring Model ◽  
Finite Element Analyses ◽  
Knitted Fabrics ◽  
Piecewise Function ◽  
Fabric Structure ◽  
Weft Knitted Fabric ◽  
Mass Spring Model ◽  
Virtual Display ◽  
Mass Spring

There are different kinds of geometrical models and physical models used to simulate weft knitted fabrics nowadays, such as loop models based on Pierce, piecewise function, spline curve, mass-spring model, and finite element analyses (FEA). Weft knitting simulation technology, including modeling and yarn reality, has been widely adopted in fabric structure designing for the manufacturer. The technology has great potentials in both industries and dynamic virtual display. The present article is aimed to review the current development of 3-D simulation technique for weft knitted fabrics.

scholarly journals Effect of time complexities and variation of mass spring model parameters on surgical simulation

2014 ◽  
Vol 9 (4) ◽  
Author(s):  
Salina Sulaiman ◽  
Tan Sing Yee ◽  
Abdullah Bade
Keyword(s):  
Soft Tissue ◽  
Human Liver ◽  
Soft Tissues ◽  
Surgical Simulation ◽  
Model Parameters ◽  
Spring Model ◽  
Surgical Simulator ◽  
Tissue Model ◽  
Mass Spring Model ◽  
Mass Spring

Physically based models assimilate organ-specific material properties, thus they are suitable in developing a surgical simulation. This study uses mass spring model (MSM) to represent the human liver because MSM is a discrete model that is potentially more realistic than the finite element model (FEM). For a high-end computer aided medical technology such as the surgical simulator, the most important issues are to fulfil the basic requirement of a surgical simulator. Novice and experienced surgeons use surgical simulator for surgery training and planning. Therefore, surgical simulation must provide a realistic and fast responding virtual environment. This study focuses on fulfilling the time complexity and realistic of the surgical simulator. In order to have a fast responding simulation, the choice of numerical integration method is crucial. This study shows that MATLAB ode45 is the fastest method compared to 2nd ordered Euler, MATLAB ode113, MATLAB ode23s and MATLAB ode23t. However, the major issue is human liver consists of soft tissues. In modelling a soft tissue model, we need to understand the mechanical response of soft tissues to surgical manipulation. Any interaction between haptic device and the liver model may causes large deformation and topology change in the soft tissue model. Thus, this study investigates and presents the effect of varying mass, damping, stiffness coefficient on the nonlinear liver mass spring model. MATLAB performs and shows simulation results for each of the experiment. Additionally, the observed optimal dataset of liver behaviour is applied in SOFA (Simulation Open Framework Architecture) to visualize the major effect.

Fuzzy Inference of Textile Animation Using Mass-Spring Model

2013 ◽  
Vol 3 (3) ◽  
pp. 148-154
Author(s):  
SeonMin Hwang ◽  
HanKyung Yun ◽  
BokHee Song
Keyword(s):  
Fuzzy Inference ◽  
Spring Model ◽  
Mass Spring Model ◽  
Mass Spring
Sign in / Sign up

Export Citation Format

Share Document