Evaluation of the Sealing Performance in Bolted Flange Connection Under Heat Condition and Internal Pressure: The Effect of Scatter in Bolt Preloads

2006 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Yoshio Takagi ◽  
Katsuhiro Yamada
Keyword(s):  
Internal Pressure ◽  
Control Method ◽  
Torque Control ◽  
Stress Distributions ◽  
Heat Condition ◽  
Flange Connection ◽  
Gas Leakage ◽  
Sealing Performance ◽  
Torque Wrench ◽  
Bolted Flange

It has been well known that a scatter in axial bolt forces of pipe flange connections tightened by the torque control method is substantial. It is necessary for evaluating the sealing performance of the pipe flange connections with the gaskets subjected to internal pressure to know the contact gasket stress distributions due to the scatter of the axial bolt forces in the connections tightened by the torque control method. Especially, when gases are used in the pipe flange connections with gaskets at a high temperature, it is necessary to evaluate the amount of gas leakage. In this study, when bolts and nuts in a pipe flange connection were tightened using a torque wrench, the axial bolt forces were measured and then the amount of gas leakage in the pipe flange connection at 50,100,150 and 200 °C was measured under internal pressure. Leakage tests were performed using Helium gases. In addition, the thermal stress distributions at the interfaces between pipe flanges and the gasket under heat condition (temperature 50,100,150 and 200 °C) and internal pressure were calculated by using the finite element method (FEM) taking into account hysteresis in the stress-strain curves of a spiral wound gasket. By using the calculated contact stress distributions and the results of the leakage tests, the sealing performance was evaluated.

Effects of Scatter in Bolt Preload of Pipe Flange Connections With Gaskets on Sealing Performance

2003 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Mitsuhiro Matsumoto ◽  
Satoshi Nagata
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Internal Pressure ◽  
Control Method ◽  
Torque Control ◽  
Stress Distributions ◽  
Flange Connection ◽  
Gas Leakage ◽  
Bolt Preload ◽  
Sealing Performance

It has been well known that a scatter in axial bolt forces of pipe flange connections tightened by the torque control method is substantial. It is necessary for evaluating the sealing performance of the pipe flange connections with the gaskets subjected to intemal pressure to know the contact gasket stress distributions due to the scatter of the axial bolt forces in the connections tightened by the torque control method. This paper deals with the leakage of the pipe flange connections with a spiral wound gasket and that with a compressed sheet gasket tightened by the torque control method. The scatter in the axial bolt forces was measured in the experiments. The contact gasket stress distributions at the interfaces of the pipe flange connections with the gaskets were calculated under the measured axial bolt forces by using elasto-plastic finite element method (FEM) taking into account hysteresis and non-linearity in the stress-strain curves of the gaskets. The effects of the scatter in the axial bolt forces tightened by the torque control method on the gas leakage were also examined by using the actual pipe flange connections. As the result, a difference in an amount of gas leakage measured was found to be substantial between our study and PVRC procedure. By using the calculated contact gasket stress distributions under the internal pressure and the results of the leakage tests, the sealing performance was evaluated. It is found that the sealing performance is worse in the actual pipe flange connection than that evaluated by PVRC procedure.

Effects of Scatter in Bolt Preload on the Sealing Performance in Bolted Flange Connections With Cover of Pressure Vessel Under Internal Pressure

2006 ◽  
Author(s):  
Satoshi Nagata ◽  
Toshiyuki Sawa ◽  
Seiichi Hamamoto
Keyword(s):  
Internal Pressure ◽  
Pressure Vessel ◽  
Torque Control ◽  
Control Methods ◽  
Stress Distributions ◽  
Flange Connection ◽  
Gas Leakage ◽  
Bolt Preload ◽  
Sealing Performance ◽  
Bolted Flange

It has been well known that the scatter in axial bolt forces of bolted flange connections tightened by torque control methods is substantial. In evaluating the sealing performance of a bolted flange connection with a gasket subjected to internal pressure, it is necessary to know the contact gasket stress distributions due to the scatter of the axial bolt forces in the flange connections tightened by torque control methods. This paper deals with the leakage of a bolted flange connection with a cover of pressure vessel including a spiral wound gasket tightened by a torque wrench. The scatter in the axial bolt forces was measured using strain gauges attached at the shank of bolts. The amount of leakage from the bolted flange connection with cover of pressure vessel was measured by so-called pressure decay method. The gas employed was Helium. From the measured leakage, the actual assembly efficiency is examined. The eight bolts and nuts were tightened according to the ASME PCC-1 method and Japanese method developed by High Pressure Institute (HPI). The difference in the bolt preload was shown between the ASME method and the HPI method. The contact gasket stress distributions at the interface of the flange connection with the gasket were calculated under the measured axial bolt forces by means of finite element analysis. Using the calculated gasket contact stress distribution, the amount of gas leakage was estimated. The estimated gas leakage was compared with the measured results.

Stress Analysis and the Sealing Performance Evaluation of Pipe Flange Connections With Gaskets Subjected to Internal Pressure and External Bending Moment: Effects of Scatter in Bolt Preload

2004 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Wataru Maezaki ◽  
Satoshi Nagata
Keyword(s):  
Finite Element Method ◽  
Internal Pressure ◽  
Control Method ◽  
Bending Moment ◽  
Torque Control ◽  
Stress Distributions ◽  
Gas Leakage ◽  
Bolt Preload ◽  
Sealing Performance ◽  
Spiral Wound

It has been well known that a scatter in axial bolt forces of pipe flange connections tightened by the torque control method is substantial. It is necessary for evaluating the sealing performance of the pipe flange connections with the gaskets subjected to internal pressure and external bending moment to know the contact gasket stress distributions due to the scatter of the axial bolt forces in the connections tightened by the torque control method. This paper deals with the leakage of the pipe flange connections with a spiral wound gasket subjected to internal pressure and external bending moment tightened by the torque control method. The scattered axial bolt forces were measured in the experiments. The contact gasket stress distributions at the interfaces between pipe flanges and the gasket were calculated under the measured axial bolt force by using elasto-plastic finite element method (FEM) taking into account hysteresis and non-linearity in the stress-strain curves of spiral wound gasket. The effects of the scatter in the axial bolt forces tightened by the torque control method on the gas leakage were also examined by using the actual pipe flange connections under internal pressure and external bending moment. By using the calculated contact stress distributions and the results of the leakage tests, the sealing performance was evaluated. It is found that the sealing performance is worse in the actual pipe flange connection than that evaluated by PVRC procedure.

Effects of Scatter in Bolt Preload on the Sealing Performance of Pipe Flange Connections Under Internal Pressure (Case Where the Nominal Diameter of Pipe Flange Connection is 20″)

2010 ◽  
Author(s):  
Yoshio Takagi ◽  
Toshiyuki Sawa ◽  
Hiroyasu Torii ◽  
Yuya Omiya
Keyword(s):  
Stress Distribution ◽  
Internal Pressure ◽  
Control Method ◽  
Torque Control ◽  
Stress Distributions ◽  
Flange Connection ◽  
Nominal Diameter ◽  
Bolt Preload ◽  
Sealing Performance ◽  
Contact Stress Distribution

It has been well known that a scatter in axial bolt forces in pipe flange connections tightened by the torque control method is substantial. In practice, pipe flange connections with the large nominal diameter tightened by the torque control method have been used in chemical industry, and so on. In our study, the characteristics of the connections with smaller nominal diameter (less than 8″) have been shown. So, in an optimum design of pipe flange connections with gaskets, it is necessary to understand the characteristics of the pipe flange connections with large nominal diameter under internal pressure and the contact gasket stress distributions due to the scatter in axial bolt forces in the connections tightened by the torque control method. In this paper, the experimental and FE analyses were done to evaluate the effect of scatter in axial bolt force on the gasket stress distribution and the sealing performance of pipe flange connections with 20″ nominal diameter. Two types of torque controlled assembling procedures, that is, ASME PCC-1 and JIS B 2251 procedures, are evaluated as an assembling procedures and an effect of scatter in the axial bolt forces obtained from the above methods is examined. Then, the effect of scatter in the axial bolt forces on the sealing performance of the connection is evaluated. The contact stress distribution in the larger pipe flange connection with 20″ nominal diameter under internal pressure is analyzed using FEM by taking into account a non-linearity and a hysteresis. The measured scatter in the axial bolt forces is applied in the FEM calculations.

Effects of Scatter in Bolt Preload of Pipe Flange Connections With Spiral Wound Gaskets Under Internal Pressure: In Case of Larger Pipe Flange Connection With 20" Nominal Diameter

2004 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Wataru Maezaki
Keyword(s):  
Internal Pressure ◽  
Contact Stress ◽  
Control Method ◽  
Torque Control ◽  
Stress Distributions ◽  
Gas Leakage ◽  
Nominal Diameter ◽  
Bolt Preload ◽  
Sealing Performance ◽  
Helium Gas

It has been well known that a scatter in axial bolt forces of pipe flange connections tightened by the torque control method is substantial. In practice, pipe flange connections with the larger nominal diameter tightened by the torque control method have been used, frequently. So, in an optimum design of pipe flange connections with gaskets, it is necessary to understand the characteristics of the pipe flange connections with larger nominal diameter under internal pressure and the contact gasket stress distributions due to the scatter of the axial bolt forces in the connections tightened by the torque control method. In this paper, the leakage tests were performed in the actual larger pipe flange connections with 20” nominal diameter using helium gas. Then, the effects of the scatter in the axial bolt forces tightened by the torque control method on the gas leakage were also examined. By using the calculated contact stress distributions and the results of the leakage tests, the sealing performance was evaluated.

FEM Stress Analysis and the Sealing Performance Evaluation in Bolted Flange Connections With Ring Joint Gasket Subjected to Internal Pressure: Effect of Scatter in Bolt Preloads

2012 ◽  
Author(s):  
Koji Kondo ◽  
Shota Tsubaki ◽  
Toshiyuki Sawa ◽  
Tsutomu Kikuchi ◽  
Yuya Omiya
Keyword(s):  
Internal Pressure ◽  
Leak Rate ◽  
Stress Distributions ◽  
Sealing Performance ◽  
Torque Wrench ◽  
Helium Gas ◽  
Higher Temperature ◽  
Bolted Flange ◽  
Better Than ◽  
Good Agreement

Bolted flange connections with ring joint gaskets have been used to seal the inner fluid under higher internal pressure and higher temperature conditions where soft gaskets such as compressed sheet gaskets cannot be applied. Bolted flange connections are frequently tightened using torque wrench, and it is known that the values of bolt preloads are scattered. The effect of the scatter on the sealing performance for bolted flange connections with compressed sheet gasket or semi-metal gasket has been examined. However, no research on the characteristics for the bolted flange connections with ring joint gasket has been found. It is necessary to know the effect of the scattered bolt preloads on the sealing performance and mechanical behavior of the connection with ring joint gasket. In addition, it is important to know an optimum method for determining the bolt preloads taking account of the scatter in bolt preloads. In this paper, leakage tests for bolted flange connections with octagonal ring joint gaskets were conducted for cases where the bolt preloads are uniform and scattered. The sealing performance of these connections with ring joint gaskets was measured and evaluated. In addition, the leak rate was estimated using the contact gasket stress distributions of the connections when the bolt preloads were uniform and scattered using 3-D FEM. Finally, the measured leak rate for the connection using helium gas was compared with the estimated results. The estimated results are in fairly good agreement with the measured values. It is found that the sealing performance of the connections tightened with the uniform bolt methods is better than that with scattered bolt preloads.

FEM Analysis and Evaluation of the Sealing Performance in Flexible Box-Shape Flanged Bolted Joints With Gaskets Subjected to Internal Pressure: Effect of the Bolt Pitch

2007 ◽  
Author(s):  
Toshiyuki Sawa ◽  
Ryo Kurosawa ◽  
Yasuaki Tatsumi
Keyword(s):  
Internal Pressure ◽  
Fem Analysis ◽  
Bolted Joints ◽  
Stress Distributions ◽  
The Finite Element Method ◽  
Analysis And Evaluation ◽  
Flange Connection ◽  
Sealing Performance ◽  
Helium Gas ◽  
Bolted Flange

Bolted joints with gaskets such as non-circular flange connections have been widely used in mechanical structures, nuclear and chemical industry, and so on. They are usually used under internal pressure as well as other loadings such as thermal, impact loadings and so on. In designing the non-circular flange connections with gaskets, it is important to evaluate the sealing performance of the non-circular flange connections with gaskets subjected to internal pressure. An important issue is how to evaluate the sealing performance in the box-shape bolted flange connections by using the contact gasket stress distributions at the interfaces, how to reduce a number of bolt and nuts, that is, how to enlarge the bolt pitch, and how to determine the initial clamping bolt force (preload) by using the new gasket constants. In this paper, the stresses of box-shape flange connection with gaskets subjected to an internal pressure are analyzed using the finite element method (FEM), taking account a hysteresis in the stress-strain curves of the gasket. The contact gasket stress distributions when the internal pressure is applied to the connection are analyzed. The leakage tests were conducted using an actual box-shape flange connection with a gasket Using the contact gasket stress distributions at the interfaces under an internal pressure (Helium gas was used) and the amount of the leakage measured in the experiment, the sealing performances are evaluated experimentally and theoretically by changing the bolt pitch in the connections. Discussion is made on the effect of the bolt pitch on the sealing performance in the above connections.

Stress Analysis and Sealing Performance Evaluation in Rectangular Box-Shape Bolted Flange Connection With Gasket Subjected to Internal Pressure

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Toshiyuki Sawa ◽  
Ryo Kurosawa ◽  
Wataru Maezaki
Keyword(s):  
Finite Element Method ◽  
Internal Pressure ◽  
Research Council ◽  
Stress Distributions ◽  
The Finite Element Method ◽  
Flange Connection ◽  
Bolt Preload ◽  
Sealing Performance ◽  
The Difference ◽  
Bolted Flange

The contact gasket stress distributions in a rectangular box-shape bolted flange connection with a compressed sheet gasket subjected to internal pressure were analyzed using the finite element method. Leakage tests were also conducted for an actual rectangular box-shape bolted flange connection with a compressed sheet gasket under internal pressure. Using the obtained contact gasket stress distributions and the results of the leakage tests, the new gasket constants were calculated. The difference in the new gasket constants between the values obtained from the present study and those from the Pressure Vessel Research Council (PVRC) procedure was substantial. In addition, a method to determine the bolt preload for a given tightness parameter was demonstrated and the difference in the determined bolt preload was shown between the present study and the PVRC procedure. The characteristics of the rectangular box-shape bolted flange connection were demonstrated by comparing those of circular bolted flange connections.

The Effect of Clamping Force and Material Properties on the Tightness Performance a Flexible Box-Shaped Flange Bolted Joint

2008 ◽  
Author(s):  
Ryou Kurosawa ◽  
Toshiyuki Sawa ◽  
Satoshi Nagata ◽  
Yasuaki Tatsumi
Keyword(s):  
Internal Pressure ◽  
Bolted Joints ◽  
Clamping Force ◽  
Stress Distributions ◽  
The Finite Element Method ◽  
Flange Connection ◽  
Sealing Performance ◽  
Helium Gas ◽  
Bolted Flange ◽  
Cover Material

Bolted joints with gaskets such as non-circular flange connections have been widely used in mechanical structures, nuclear and chemical industry, and so on. They are usually used under internal pressure as well as other loadings such as thermal, impact loadings and so on. In designing the non-circular flange connections with gaskets, it is important to evaluate the sealing performance of the non-circular flange connections with gaskets subjected to internal pressure. An important issue is how to evaluate the sealing performance in the box-shaped bolted flange connections by using the contact gasket stress distributions at the interfaces, how to reduce the weight and how to determine the initial clamping bolt force (preload) by using the new gasket constants. In this paper, the stresses of box-shaped flange connection with gaskets subjected to an internal pressure are analyzed using the finite element method (FEM), taking account a hysteresis in the stress-strain curves of the gasket. The reduced contact gasket stress distributions are analyzed when the internal pressure is applied to the connection. The leakage tests were conducted using an actual box-shaped flange connection with a gasket. Using the reduced contact gasket stress distributions at the interfaces under an internal pressure (Helium gas was used) and the amount of the leakage measured in the experiment, the sealing performances are evaluated experimentally and theoretically by changing the initial clamping force and cover material in the connections. In addition, the sealing performance of the connection with raised face is also examined. Discussion is made on the effects of the initial clamping force, cover material and the types of facing on the sealing performance in the above connections.

FEM Stress Analysis and Evaluation of the Sealing Performance in Flexible Box-Shape Bolted Flange Gasketed Joints Subjected to Internal Pressure

2009 ◽  
Author(s):  
Kentaro Tenma ◽  
Ryou Kurosawa ◽  
Toshiyuki Sawa
Keyword(s):  
Internal Pressure ◽  
Automobile Industry ◽  
Stress Distributions ◽  
The Finite Element Method ◽  
Analysis And Evaluation ◽  
Flange Connection ◽  
Sealing Performance ◽  
Helium Gas ◽  
Bolted Flange ◽  
Bolt Diameter

Bolted joints inserting gaskets such as box-shape flange connections have been widely used in mechanical structures, nuclear and chemical industry, and so on. In automobile industry, box-shape connections are applied in oil-pan structure. They are usually used under internal pressure as well as other loadings such as thermal, impact loadings and so on. In designing the box-shape flange connections with gaskets, it is important to evaluate the sealing performance of connections under internal pressure. An important issue is how to evaluate the sealing performance in the connections by using the contact gasket stress distributions at the interfaces and how to determine the initial clamping bolt force (preload) for preventing leakage. In this paper, the stresses of box-shape flange connection with gaskets subjected to an internal pressure are analyzed using the finite element method (FEM), taking into account a hysteresis in the stress-strain curves of the gasket. The contact gasket stress distributions of the connections under the internal pressure are analyzed. The leakage tests were conducted using an actual box-shape flange connection with a gasket. Using the contact gasket stress distributions at the interfaces under an internal pressure (Helium gas was used) and the amount of the leakage measured in the experiment, the sealing performances are evaluated experimentally and numerically. Furthermore, the effect of the nominal bolt diameter, the bolt pitch and flange cover seating types (raised face / flat face) is examined on the sealing performances of box-shape flange connections. Discussion is made on the sealing performance in the above connections.

Sign in / Sign up

Export Citation Format

Share Document