scholarly journals Structural health monitoring by extraction of coherent guided waves from diffuse fields

2008 ◽  
Vol 123 (1) ◽  
pp. EL8-EL13 ◽  
Author(s):  
Karim G. Sabra ◽  
Ankit Srivastava ◽  
Francesco Lanza di Scalea ◽  
Ivan Bartoli ◽  
Piervincenzo Rizzo ◽  
...  
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Guided Waves ◽  
Structural Health ◽  
Diffuse Fields

scholarly journals Experimentation and Adaptive Modeling for Temperature Effect Quantification in PVP Structural Health Monitoring With PWAS

2015 ◽  
Author(s):  
Tuncay Kamas ◽  
Banibrata Poddar ◽  
Bin Lin ◽  
Lingyu Yu ◽  
Victor Giurgiutiu
Keyword(s):  
Elevated Temperature ◽  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Thermal Effects ◽  
Guided Waves ◽  
Substrate Material ◽  
Ultrasonic Waves ◽  
Material Parameters ◽  
Structural Health

The thermal effects at elevated temperatures mostly exist for pressure vessel and pipe (PVP) applications. The technologies for diagnosis and prognosis of PVP systems need to take the thermal effect into account and compensate it on sensing and monitoring of PVP structures. One of the extensively employed sensor technologies has been permanently installed piezoelectric wafer active sensor (PWAS) for in-situ continuous structural health monitoring (SHM). Using the transduction of ultrasonic elastic waves into voltage and vice versa, PWAS has been emerged as one of the major SHM sensing technologies. However, the dynamic characteristics of PWAS need to be explored prior its installation for in-situ SHM. Electro-mechanical impedance spectroscopy (EMIS) method has been utilized as a dynamic descriptor of PWAS and as a high frequency local modal sensing technique by applying standing waves to indicate the response of the PWAS resonator by determining the resonance and anti-resonance frequencies. Another SHM technology utilizing PWAS is guided wave propagation (GWP) as a far-field transient sensing technique by transducing the traveling guided ultrasonic waves (GUW) into substrate structure. The paper first presents EMIS method that qualifies and quantifies circular PWAS resonators under traction-free boundary condition and in an ambience with increasing temperature. The piezoelectric material degradation was investigated by introducing the temperature effects on the material parameters that are obtained from experimental observations as well as from related work in literature. GWP technique is also presented by inclusion of the thermal effects on the substrate material. The MATLAB GUI under the name of Wave Form Revealer (WFR) was adapted for prediction of the thermal effects on coupled guided waves and dynamic structural change in the substrate material at elevated temperature. The WFR software allows for the analysis of multimodal guided waves in the structure with affected material parameters in an ambience with elevated temperature.

Use of delay and sum for sparse reconstruction improvement for structural health monitoring

2019 ◽  
Vol 30 (18-19) ◽  
pp. 2919-2931 ◽  
Author(s):  
Ali Nokhbatolfoghahai ◽  
Hossein M Navazi ◽  
Roger M Groves
Keyword(s):  
Structural Health Monitoring ◽  
Damage Detection ◽  
Health Monitoring ◽  
Guided Waves ◽  
Lamb Waves ◽  
Spot Size ◽  
Sparse Reconstruction ◽  
Reconstruction Method ◽  
Structural Health ◽  
Computational Performance

To perform active structural health monitoring, guided Lamb waves for damage detection have recently gained extensive attention. Many algorithms are used for damage detection with guided waves and among them, the delay-and-sum method is the most commonly used algorithm because of its robustness and simplicity. However, delay-and-sum images tend to have poor accuracy with a large spot size and a high noise floor, especially in the presence of multiple damages. To overcome these problems, another method that is based on sparse reconstruction can be used. Although the images produced by the sparse reconstruction method are superior to the conventional delay-and-sum method, it has the challenges of the time and cost of computations in comparison with the delay-and-sum method. Also, in some cases in multi-damage detection, the sparse reconstruction method totally fails. In this article, using prior support information of the structure achieved by the delay-and-sum method, a hybrid method based on sparse reconstruction method is proposed to improve the computational performance and robustness of sparse reconstruction method in the case of multi-damage presence. The effectiveness of the proposed method in detecting damages is demonstrated experimentally and numerically on a simple aluminum plate. The technique is also shown to accurately identify and localize multi-site damages as well as single damage with low sampled signals.

scholarly journals Structural health monitoring for delamination detection and location in wind turbine blades employing guided waves

Wind Energy ◽  
2019 ◽  
Vol 22 (5) ◽  
pp. 698-711 ◽  
Author(s):  
Carlos Quiterio Gómez Muñoz ◽  
Fausto Pedro García Marquez ◽  
Borja Hernandez Crespo ◽  
Kena Makaya
Keyword(s):  
Structural Health Monitoring ◽  
Wind Turbine ◽  
Health Monitoring ◽  
Guided Waves ◽  
Turbine Blades ◽  
Wind Turbine Blades ◽  
Structural Health ◽  
Delamination Detection

scholarly journals Analysis of Guided Wave Propagation in a Multi-Layered Structure in View of Structural Health Monitoring

2019 ◽  
Vol 9 (21) ◽  
pp. 4600 ◽  
Author(s):  
Yevgeniya Lugovtsova ◽  
Jannis Bulling ◽  
Christian Boller ◽  
Jens Prager
Keyword(s):  
Wave Propagation ◽  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Guided Waves ◽  
Oil And Gas ◽  
Numerical Approach ◽  
Guided Wave ◽  
Mode Shapes ◽  
Engineering Structures ◽  
Structural Health

Guided waves (GW) are of great interest for non-destructive testing (NDT) and structural health monitoring (SHM) of engineering structures such as for oil and gas pipelines, rails, aircraft components, adhesive bonds and possibly much more. Development of a technique based on GWs requires careful understanding obtained through modelling and analysis of wave propagation and mode-damage interaction due to the dispersion and multimodal character of GWs. The Scaled Boundary Finite Element Method (SBFEM) is a suitable numerical approach for this purpose allowing calculation of dispersion curves, mode shapes and GW propagation analysis. In this article, the SBFEM is used to analyse wave propagation in a plate consisting of an isotropic aluminium layer bonded as a hybrid to an anisotropic carbon fibre reinforced plastics layer. This hybrid composite corresponds to one of those considered in a Type III composite pressure vessel used for storing gases, e.g., hydrogen in automotive and aerospace applications. The results show that most of the wave energy can be concentrated in a certain layer depending on the mode used, and by that damage present in this layer can be detected. The results obtained help to understand the wave propagation in multi-layered structures and are important for further development of NDT and SHM for engineering structures consisting of multiple layers.

Sign in / Sign up

Export Citation Format

Share Document