Investigation of the Coupling of Unsteady Lift to Lower Order Acoustic Duct Modes in an Axial Flow Fan

1983 ◽  
Vol 73 (2) ◽  
pp. 697-697
Author(s):  
James P. Cowan
Keyword(s):  
Lower Order ◽  
Axial Flow ◽  
Axial Flow Fan ◽  
Unsteady Lift

Improvement of Stalling Characteristics of an Axial-Flow Fan by Radial-Vaned Air-Separators

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
Nobuyuki Yamaguchi ◽  
Masayuki Ogata ◽  
Yohei Kato
Keyword(s):  
Solid Wall ◽  
Axial Flow ◽  
Internal Flow ◽  
Rotor Blades ◽  
Relative Location ◽  
Flow Conditions ◽  
Axial Flow Fan ◽  
Light Load ◽  
Stall Prevention ◽  
Air Separator

An improved construction of air-separator device, which has radial-vanes embedded within its inlet circumferential opening with their leading-edges facing the moving tips of the fan rotor-blades so as to scoop the tip flow, was investigated with respect to the stall-prevention effect on a low-speed, single-stage, lightly loaded, axial-flow fan. Stall-prevention effects by the separator layout, relative location of the separator to the rotor-blades, and widths of the openings of the air-separator inlet and exit were parametrically surveyed. As far as the particular fan is concerned, the device together with the best relative location has proved to be able to eliminate effectively the stall zone having existed in the original solid-wall characteristics, which has confirmed the promising potential of the device. Guidelines were obtained from the data for optimizing relative locations of the device to the rotor-blades, maximizing the stall-prevention effect of the device, and minimizing the axial size of the device for a required stall-prevention effect, at least for the particular fan and possibly for fans of similar light-load fans. The data suggest the changing internal flow conditions affected by the device conditions.

The Design of a Large Diameter Axial Flow Fan for Air-Cooled Heat Exchanger Applications

2017 ◽  
Author(s):  
Michael B. Wilkinson ◽  
Johan van der Spuy ◽  
Theodor W. von Backström
Keyword(s):  
Flow Field ◽  
Large Diameter ◽  
Axial Flow ◽  
Pressure Rise ◽  
Design Procedure ◽  
Axial Flow Fan ◽  
Disk Model ◽  
Actuator Disk ◽  
Static Efficiency ◽  
Air Cooled Heat Exchanger

An axial flow fan design methodology is developed to design large diameter, low pressure rise, rotor-only fans for large air-cooled heat exchangers. The procedure aims to design highly efficient axial flow fans that perform well when subjected to off design conditions commonly encountered in air-cooled heat exchangers. The procedure makes use of several optimisation steps in order to achieve this. These steps include optimising the hub-tip ratio, vortex distribution, blading and aerofoil camber distributions in order to attain maximum total-to-static efficiency at the design point. In order to validate the design procedure a 24 ft, 8 bladed axial flow fan is designed to the specifications required for an air-cooled heat exchanger for a concentrated solar power (CSP) plant. The designed fan is numerically evaluated using both a modified version of the actuator disk model and a three dimensional periodic fan blade model. The results of these CFD simulations are used to evaluate the design procedure by comparing the fan performance characteristic data to the design specification and values calculated by the design code. The flow field directly down stream of the fan is also analysed in order to evaluate how closely the numerically predicted flow field matches the designed flow field, as well as determine whether the assumptions made in the design procedure are reasonable. The fan is found to meet the required pressure rise, however the fan total-to-static efficiency is found to be lower than estimated during the design process. The actuator disk model is found to under estimate the power consumption of the fan, however the actuator disk model does provide a reasonable estimate of the exit flow conditions as well as the total-to-static pressure characteristic of the fan.

Based on ANSYS APDL Language Moving Blade Adjustable Axial Flow Fan Optimization Design

2013 ◽  
Vol 655-657 ◽  
pp. 435-444
Author(s):  
Dong Xia Niu ◽  
Xian Yi Meng ◽  
Ai Hua Zhu
Keyword(s):  
Optimization Design ◽  
Lift Coefficient ◽  
Axial Flow ◽  
Optimization Method ◽  
Structure Parameters ◽  
Continuous Variables ◽  
State Variables ◽  
Axial Flow Fan ◽  
Installation Angle ◽  
Design Variables

In the case of multiple loading conditions, a moving blade adjustable axial flow fan structure parameters are optimized by ANSYS. It is to achieve greater efficiency and less noise for the optimization goal. For different conditions, establish efficiency, noise comprehensive objective function using weighted coefficient method. Select impeller diameter, the wheel hub ratio, leaf number, lift coefficient, speed as design variables, Choose blade installation Angle, the wheel hub place dynamic load coefficient, cascade consistency, allowable safety coefficient as optimization of the state variables. Design variables contain continuous variables and discrete variable. Through the optimization method, we get the optimal structure parameters finally. And at the same time get the corresponding optimal blade installation Angle,under different working conditions.

Sign in / Sign up

Export Citation Format

Share Document