Field experimental cells to evaluate the hydrogeological behaviour of oxygen barriers made of silty materials

An in situ study was initiated to evaluate the efficiency of silts as moisture-retaining material in covers with capillary barrier effects (CCBEs) that aim at controlling the production of acid mine drainage (AMD). This investigation included the construction of four experimental cells covered by different layered cover configurations. Each CCBE was instrumented to monitor its hydrogeological behaviour. The degree of saturation (Sr) in the moisture-retaining (silty) materials was usually maintained above 85%, while Sr in the two sand layers placed above and below the silts was generally lower than 30%–50% (typical hydrogeological behaviour of efficient CCBEs). Suction measurements in the different layers of the four CCBEs were consistent with the observed Sr measurements during the four years of monitoring. The suctions measured in the moisture-retaining materials were lower than their respective air-entry values (AEV), while suctions largely exceeded the AEV of the sand in the capillary break layers. The oxygen flux calculations confirm that in each of the four CCBEs the flux through the CCBEs remained low for the entire duration of the experiment, hence limiting the generation of AMD. This study also confirmed the ability of silty materials to act as moisture retaining in a CCBE. Key words: cover with capillary barrier effects, acid mine drainage, experimental cells, in situ monitoring, unsaturated flow, diffusion, oxygen flux.

Download Full-text

Preliminary geotechnical assessment of the potential use of mixtures of soil and acid mine drainage neutralization sludge as materials for the moisture retention layer of covers with capillary barrier effects

Canadian Geotechnical Journal ◽

10.1139/cgj-2014-0319 ◽

2016 ◽

Vol 53 (5) ◽

pp. 828-838 ◽

Cited By ~ 3

Author(s):

Mamert Mbonimpa ◽

Médard Bouda ◽

Isabelle Demers ◽

Mostafa Benzaazoua ◽

Denis Bois ◽

...

Keyword(s):

Acid Mine Drainage ◽

Mine Drainage ◽

Capillary Barrier ◽

Moisture Retention ◽

Mine Site ◽

Barrier Effects ◽

Acid Mine ◽

Geotechnical Assessment ◽

Site Rehabilitation ◽

Water Contents

Lime treatment of acid mine drainage (AMD) generates sludge that is commonly stored in ponds for dewatering. The use of soil-aged sludge-based mixtures for mine site rehabilitation can allow the emptying of existing basins, thus extending their storage capacity, reducing the volume of the borrow soil pit required for mine site rehabilitation, and consequently reducing the mine footprint. The authors investigated the geotechnical properties of silty soil–sludge mixtures (SSMs) as possible components of covers with capillary barrier effects (CCBEs) to prevent AMD generation from mine waste. SSMs with β values of 10%, 15%, 20%, and 25% sludge (β = wet sludge mass / wet soil mass) were studied. Two water contents were considered for each of the mixture components: 175% and 200% for the sludge and 7.5% and 12.5% for the soil. Results indicate that saturated hydraulic conductivity (ksat) values were in the range of 10−5 cm/s for the soil and SSMs at void ratios ranging from 0.28 to 0.53, with values decreasing slightly when β was increased from 0% to 25%. The air-entry value (AEV) increased from 20 kPa for the soil alone to 35 kPa for the SSM with β = 25%. These values of ksat and AEV are comparable to those of materials used in the moisture retention layers of existing efficient CCBEs. However, the volumetric shrinkage increased from about 2% for the soil alone to values ranging between 24% and 32% for the SSM with β = 25%, depending on the initial water contents of the components. Tools are provided to estimate to which extent the use of sludge in SSMs can reduce the volume of borrow natural soil required for a moisture retention layer of a CCBE.

Download Full-text