scholarly journals Seismic Vulnerability Evaluation of a Three-Span Continuous Beam Railway Bridge

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Chongwen Jiang ◽  
Biao Wei ◽  
Dianbin Wang ◽  
Lizhong Jiang ◽  
Xuhui He
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Seismic Isolation ◽  
Seismic Vulnerability ◽  
Element Model ◽  
Seismic Demand ◽  
Continuous Beam ◽  
Railway Bridge ◽  
Demand Model ◽  
Probabilistic Seismic Demand

In order to evaluate the seismic vulnerability of a railway bridge, a nonlinear finite element model of typical three-span continuous beam bridge on the Sichuan-Tibet railway in China was built. It further aimed at performing a probabilistic seismic demand analysis based on the seismic performance of the above-mentioned bridge. Firstly, the uncertainties of bridge parameters were analyzed while a set of finite element model samples were formulated with Latin hypercube sampling method. Secondly, under Wenchuan earthquake ground motions, an incremental dynamic method (IDA) analysis was performed, and the seismic peak responses of bridge components were recorded. Thirdly, the probabilistic seismic demand model for the bridge principal components under the prerequisite of two different kinds of bearing, with and without seismic isolation, was generated. Finally, comparison was drawn to further ascertain the effect of two different kinds of bearings on the fragility components. Based on the reliability theory, results were presented concerning the seismic fragility curves.

Physical and Numerical Simulations of the Seismic Response of a 1,100 kV Power Transformer Bushing

2018 ◽  
Vol 34 (3) ◽  
pp. 1515-1541 ◽  
Author(s):  
Guo-Liang Ma ◽  
Qiang Xie ◽  
Andrew S. Whittaker
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Numerical Simulations ◽  
Seismic Vulnerability ◽  
Power Transformer ◽  
Element Model ◽  
Ground Shaking ◽  
Earthquake Simulator ◽  
Physical Experiments ◽  
Seismic Tests

Power transformers and bushings are key pieces of substation equipment and are vulnerable to the effects of earthquake shaking. The seismic performance of a 1,100 kV bushing, used in an ultra-high voltage (UHV) power transformer, is studied using a combination of physical and numerical experiments. The physical experiments utilized an earthquake simulator and included system identification and seismic tests. Modal frequencies and shapes are derived from white noise tests. Acceleration, strain, and displacement responses are obtained from the uniaxial horizontal seismic tests. A finite element model of the 1,100 kV bushing is developed and analyzed, and predicted and measured results are compared. There is reasonably good agreement between predicted and measured responses, enabling the finite element model to be used with confidence for seismic vulnerability studies of transformer-bushing systems. A coupling of the experimental and numerical simulations enabled the vertically installed UHV bushing to be seismically qualified for three-component ground shaking with a horizontal zero-period acceleration of 0.53 g.

scholarly journals INFLUENCE OF CURVED WEB CLOSED STEEL SECTIONS IN BRIDGE DESIGN

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Gilles Van Staen ◽  
Hans De Backer ◽  
Philippe Van Bogaert
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Urban Area ◽  
Element Model ◽  
Structural Elements ◽  
Railway Bridge ◽  
Bridge Design ◽  
Steel Sections ◽  
Steel Panels ◽  
Closed Steel

A bridge is nowadays more than a structure that connects people over an obstacle. When a bridge has to be built in an urban area, either it has to be a landmark or it should blend away in the environment. The use of curved steel panels is one option to obtain these requirements. However, due to a lack of knowledge, engineers end up with a conservative design to implement these structural elements. For that reason, a Finite Element Model is made of a railway bridge, where the outer webs of the main girders have a varying web curvature. Six different models are made and compared. The most important parameters that are compared are the deformations and the stresses in the webs. The study finds that curved webs have an equal or even better behavior than flat webs, even with smaller web thickness. This makes that designers can use curved webs in their design, without needing extra steel to make their design safe.

Modelling the non-linear behaviour of the pot bearings of railway bridge KW51

2021 ◽  
Author(s):  
Menno Van De Velde ◽  
Kristof Maes ◽  
Geert Lombaert
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Model Parameters ◽  
Railway Bridge ◽  
Digital Twin ◽  
Linear Finite Element ◽  
Non Linear ◽  
First Results ◽  
Linear Behaviour

<p>Railway bridge KW51 in Leuven, Belgium, has been monitored since October 2018 with the aim of constructing a digital twin, i.e. a virtual representation that mimics the behaviour of the actual struc- ture. A linear finite element model of the bridge was updated using measurements carried out on the bridge. The pot bearings of the bridge, however, are found to behave in a non-linear way. This paper describes a methodology to account for this non-linear behaviour in the model, where friction in the bearings is accounted for by means of non-linear Bouc-Wen elements. The first results are presented, showing that the overall non-linear behaviour of the bearings during a train passage is well captured but that further research is needed to calibrate the model parameters.</p>

Stange Overpass: Finite Element Model Updating of an Unconventional Railway Bridge

2021 ◽  
pp. 889-901
Author(s):  
Emrah Erduran ◽  
Kltigin Demirlioglu ◽  
Albert Lau ◽  
Kameran Aziz ◽  
Ian Willoughby ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Element Model ◽  
Finite Element Model Updating ◽  
Railway Bridge

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Sign in / Sign up

Export Citation Format

Share Document