scholarly journals Effects of Universal Adhesive on Shear Bond Strength of Resin Cement to Zirconia Ceramic with Different Surface Treatments

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
Zohreh Moradi ◽  
Farnoosh Akbari ◽  
Sara Valizadeh
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Resin Cement ◽  
Zirconia Ceramic ◽  
Single Bond ◽  
Universal Adhesive

Aim. This study aimed to assess shear bond strength (SBS) of resin cement to zirconia ceramic with different surface treatments by using Single Bond Universal. Methods. In this in vitro study, 50 zirconia discs (2 × 6 mm) were divided into 5 groups of (I) sandblasting with silica-coated alumina (CoJet)  + silane + Single Bond 2, (II) sandblasting with CoJet + Single Bond Universal, (III) sandblasting with alumina + Single Bond Universal, (IV) sandblasting with alumina + Z-Prime Plus, and (V) Single Bond Universal with no surface treatment. Resin cement was applied in plastic tubes (3 × 5 mm2), and after 10,000 thermal cycles, the SBS was measured by a universal testing machine. The mode of failure was determined under a stereomicroscope at × 40 magnification. Data were analyzed using one-way ANOVA. Results. The maximum (6.56 ± 4.29 MPa) and minimum (1.94 ± 1.96 MPa) SBS values were noted in groups III and I, respectively. Group III had the highest frequency of mixed failure (60%). Group V had the maximum frequency of adhesive failure (100%). Conclusion. Single Bond Universal + sandblasting with alumina or silica-coated alumina particles is an acceptable method to provide a strong SBS between resin cement and zirconia.

scholarly journals Micro-shear bond strength of bioactive cement to translucent zirconia after thermocycyling: a comparative in-vitro study

2020 ◽  
Vol 23 (1) ◽  
Author(s):  
Menna Ahmed ElGendy ◽  
Ihab Mosleh ◽  
Hanaa Zaghloul
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Resin Cement ◽  
Zirconia Ceramic ◽  
Control Group ◽  
Significant Difference ◽  
Before And After

Objective: the purpose of the study was to evaluate the micro-shear bond strength of different cements to translucent zirconia before and after thermocycling aging. Material and methods: Twelve translucent zirconia ceramic discs were used in the study. Specimens were sandblasted using 50 ‎μm aluminum oxide (Al2O3) particles. The specimens were divided into three groups (n = 4) according to the cement type: Panavia resin cement (control group), resin modified glass ionomer (RMGI), and Activa bioactive cement. Each group was further sub-divided into two equal subgroups (n = 2) according to whether the specimens were subjected to thermocycling or not. Thermocycling was performed in distilled water at 5000 cycles between 5 oC - 55 oC. The micro-shear bond strength test (μSBS) was measured using universal testing machine. Kruskal-Wallis test was used to compare between the three cements. Dunn’s test was used for pair-wise comparisons when Kruskal-Wallis test is significant. Mann-Whitney U test was used to compare between micro-shear bond strength before and after thermocycling P ≤ 0.05. Results: In non-aged subgroups, there was no significant difference between Panavia and Activa; both showed significantly the highest mean μSBS values (22.9 MPa, 31.3 MPa respectively). While, RMGI showed the lowest μSBS values (4.7 MPa).  In thermocycled subgroups, Panavia showed significantly the highest mean μSBS values (32.2 MPa). There was no significant difference between RMGI and Activa; both showed the lowest significant mean μSBS values (3.2 MPa and 8.7 MPa respectively). Conclusions: RMGI and Activa couldn’t be considered long-term reliable materials for cementing zirconia. However, Panavia provided the most durable bond to zirconia.KEYWORDSBioactive cement; Micro-shear bond strength; Resin cement; Translucent zirconia.

scholarly journals Shear Bond Strength of Three Orthodontic Bonding Systems on Enamel and Restorative Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Andreas Hellak ◽  
Jennifer Ebeling ◽  
Michael Schauseil ◽  
Steffen Stein ◽  
Matthias Roggendorf ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Control Group ◽  
Metal Composite ◽  
Universal Adhesive ◽  
Restorative Materials ◽  
Bonding Systems

Objective.The aim of this in vitro study was to determine the shear bond strength (SBS) and adhesive remnant index (ARI) score of two self-etching no-mix adhesives (iBond™and Scotchbond™) on different prosthetic surfaces and enamel, in comparison with the commonly used total etch system Transbond XT™.Materials and Methods. A total of 270 surfaces (1 enamel and 8 restorative surfaces,n=30) were randomly divided into three adhesive groups. In group 1 (control) brackets were bonded with Transbond XT primer. In the experimental groups iBond adhesive (group 2) and Scotchbond Universal adhesive (group 3) were used. The SBS was measured using a Zwicki 1120™testing machine. The ARI and SBS were compared statistically using the Kruskal–Wallis test (P≤0.05).Results. Significant differences in SBS and ARI were found between the control group and experimental groups.Conclusions. Transbond XT showed the highest SBS on human enamel. Scotchbond Universal on average provides the best bonding on all other types of surface (metal, composite, and porcelain), with no need for additional primers. It might therefore be helpful for simplifying bonding in orthodontic procedures on restorative materials in patients. If metal brackets have to be bonded to a metal surface, the use of a dual-curing resin is recommended.

scholarly journals Effect of Contamination with Hemostatic Agent on Shear Bond Strength of Composite to Dentin Using G-Premio and Single Bond Universal Adhesives

2021 ◽  
Author(s):  
Zahra Khamverdi ◽  
Naemeh Karimian ◽  
Maryam Farhadian ◽  
Hamed Gheitouli
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Hemostatic Agent ◽  
Control Group ◽  
Single Bond ◽  
Failure Data ◽  
Universal Adhesives

Objectives: Bond strength of composite restorations plays an important role in their success. This in vitro study evaluated the effect of a hemostatic agent on shear bond strength of universal adhesives. Materials and Methods: Thirty-six extracted human molars were used in this study. Buccal and lingual surfaces were reduced to obtain flat dentin surfaces and were ground with a silicone paper. The samples were randomly divided into three groups (n=12) based on the application of hemostatic agent: group 1: no contamination (control), group 2: aluminum chloride application, and group 3: ferric sulfate application. Each group was then divided into two subgroups (n=6) for using G-Premio and Single Bond Universal. Resin cylinders (Filtek Z550) were bonded to dentin surfaces according to the manufacturer’s instructions. After 1000 thermal cycles, shear load was applied to the specimens using a universal testing machine at a crosshead speed of 1 mm/min until failure. Data were statistically analyzed using two-way ANOVA and Tukey’s post-hoc test (α=0.05). Results: There were statistically significant differences in shear bond strength of the three main groups for both G-Premio and Single Bond Universal (P<0.05). When the adhesive systems were compared with each other, G-Premio showed higher shear bond strength than Single Bond Universal (P<0.05). Conclusion: Contamination with hemostatic agents had an adverse effect on the shear bond strength of universal adhesives. Moreover, G-Premio yielded a higher bond strength than Single Bond Universal.

scholarly journals Comparing Shear Bond Strength of Two Step vs One Step B onding Agents on Ground Enamel and Dentin: An in vitro Study

2014 ◽  
Vol 3 (1) ◽  
pp. 1-3
Author(s):  
Shubhangi Mani ◽  
Darshan Deepak Shah ◽  
Narendra Manwar ◽  
Rushabh Malde
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Single Bond ◽  
Universal Adhesive ◽  
Bonding Agents ◽  
Ground Enamel ◽  
Significant Difference ◽  
One Step

ABSTRACT Aim To compare the shear bond strength of Tetric N Bond (Ivoclar Vivadent) and Single Bond Universal Adhesive (3M ESPE, MN, USA) on ground enamel and dentin. Materials and methods A total of 30 extracted human maxillary and mandibular molars and premolars were used for this study and divided into two groups which were treated with Tetric N Bond (Ivoclar Vivaden) t- and Single Bond Universal Adhesive (3M ESPE, MN, USA). The shear bond strength was tested on Universal testing machine (Instron). Results There was statistically significant difference in the shear bond strength among the two groups. Conclusion Based on the results (Tetric N Bond, Ivoclar Vivadent) had higher bond strength than Single Bond Universal Adhesive (3M ESPE, MN, USA) on ground enamel and dentin. How to cite this article Shah DD, Chandak M, Manwar N, Mani S, Mani A, Saini R, Malde R. Comparing Shear Bond Strength of Two Step vs One Step Bonding Agents on Ground Enamel and Dentin: An in vitro Study. Int J Experiment Dent Sci 2014;3(1):1-3.

scholarly journals Shear Bond Strength of Metal and Ceramic Brackets to Composite Using Single Bond and Universal Adhesive

2020 ◽  
Vol 8 (D) ◽  
pp. 1-6
Author(s):  
Hoda Pouyanfar ◽  
Amin Golshah ◽  
Matin Shekarbeigi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Bonding Agent ◽  
Single Bond ◽  
Universal Adhesive ◽  
Composite Restorations ◽  
Significant Difference ◽  
Ceramic Brackets

AIM: This study aimed to assess the shear bond strength (SBS) of metal and ceramic brackets bonded to composite restorations using single bond 5th generation bonding agent and G-Premio Bond universal adhesive. MATERIALS AND METHODS: In this in vitro, experimental study, 60 sound extracted human premolars were veneered with composite and were then randomly divided into four groups (n = 15) of Single Bond + Transbond XT + metal brackets, universal adhesive + Transbond XT+ metal brackets, Single Bond + Transbond XT + ceramic brackets, and universal adhesive + Transbond XT + ceramic brackets. Twenty-four hours after thermocycling, the SBS of brackets was measured using a universal testing machine. The adhesive remnant index (ARI) score was also determined under a stereomicroscope. Two-way ANOVA was used to compare the groups (p <0.05). RESULTS: No significant difference was found in the mean SBS of ceramic and metal brackets or between the two bonding agents (p > 0.05). The interaction effect of type of bracket and type of bonding agent on SBS was not significant (p > 0.05). ARI score I had the highest frequency in Single Bond + Metal bracket group. The highest frequency of ARI score V was noted in the Single Bond + Ceramic bracket group. A comparison of ARI scores of metal bracket groups showed a significant difference between single bond and universal adhesive (p = 0.002). CONCLUSION: Both adhesives can provide adequate SBS for the bonding of metal and ceramic brackets to composite restorations.

scholarly journals Influence of irradiation with Er:YAG laser on the shear bond strength of a resin cement to feldspathic ceramic - in vitro study

Cerâmica ◽  
2015 ◽  
Vol 61 (358) ◽  
pp. 244-250 ◽  
Author(s):  
M. C. Loffredo ◽  
F. S. Hanashiro ◽  
W. Steagall Júnior ◽  
M. N. Youssef ◽  
W. C. de Souza-Zaroni
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Er:Yag Laser ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Resin Cement ◽  
Air Abrasion ◽  
Yag Laser

<p>Although several conventional surface treatments have been used on feldspathic ceramic, a few studies investigated the effects of the irradiation with Er: YAG laser using different parameters. The aim of this in vitro study was to evaluate the shear bond strength of a resin cement to feldspathic ceramic, after the application of different surface treatments, especially the irradiation with Er:YAG laser. Forty-two discs made of a feldspathic ceramic were divided into six groups (n = 7): G1: control group - 10% hydrofluoric acid (HF), G2: Air abrasion with Al2O3 + HF; G3: Er: YAG laser with 500 mJ/4Hz, G4: Er: YAG laser with 500 mJ/4Hz: + HF; G5: Er: YAG laser with 400 mJ/6Hz and G6: Er:YAG laser with 400 mJ/6Hz + HF. After this, all the specimens were treated with silane, and then a resin cement cylinder was built on the treated ceramic surface. After 24 h at 37 oC, specimens were submitted to the shear bond strenght test and stereoscopic evaluation to determine the type of failure. The mean bond strength values (MPa) obtained were: G1 - 17.55, G2 - 18.80, G3 - 21.80, G4 - 12.62, G5 - and 15.81 G6- 11.59. After performing the ANOVA and Tukey's test, it was concluded that the group irradiated with Er:YAG laser at 500mJ/4Hz performed similarly to the groups that received the conventional treatments, such as hydrofluoric acid etching and the combination of air abrasion plus hydrofluoric acid, and was higher than the other groups irradiated with Er:YAG laser.</p>

Shear bond strength of metal/ceramic Interface after different surface treatments: an in vitro study. Resistência ao cisalhamento da interface metal/cerâmica após diferentes tratamentos de superfície: estudo in vitro

2013 ◽  
Author(s):  
Sílvia Fontes Do Amaral Pereira
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Vitro Study ◽  
Metal Ceramic

O objetivo do presente estudo in vitro foi verificar, através de teste de cisalhamento, a resistência de união da liga Wironia®light, à base de níquel-cromo sem berílio, sujeita a diferentes tratamentos de superfície, às cerâmicas Vita VM13 e Noritake. Foram confeccionados oitenta espécimes cilíndricos metálicos, com o auxílio de uma matriz de aço, nas dimensões de 4 mm de diâmetro por 4 mm de altura. Os espécimes foram divididos em oito grupos (n=10), de acordo com o tipo de tratamento superficial aplicado à liga metálica e com o tipo de cerâmica testada. Estes foram avaliados de acordo com os critérios de resistência ao cisalhamento e, com o auxílio de microscopia óptica, foi avaliada a área de cerâmica remanescente aderida ao metal após a fratura. Os corpos-de-prova do G6 (fabricados em Cerâmica Noritake com jateamento-26,401 ± 11,637 MPa) apresentaram maior resistência ao cisalhamento (p> 0,05) enquanto que os menores valores foram registrados no G4 (Cerâmica Vita com utilização de broca-13,440 ± 7,766 MPa). G6 (19425,4 μm2) apresentou a maior área de cerâmica aderida ao metal (p> 0,05) enquanto que o G4 (2310,2 μm2) apresentou a menor área. Concluiu-se que G6 obteve os valores mais altos de resistência ao cisalhamento e de remanescente cerâmico aderido à superfície metálica enquanto que o G4 obteve os valores mais baixos. Descritores: Restaurações metalo-cerâmicas; ligas de níquel-cromo;porcelana dentária.

scholarly journals Efficacy of Fiber Post Bonding To Root Dentin after Different Obturation Techniques and Cementation Timings: In Vitro Study

2018 ◽  
Vol 6 (9) ◽  
pp. 1707-1711
Author(s):  
Rami M. Atia ◽  
Nada Omar ◽  
Haidy Nabil ◽  
Yousra Aly
Keyword(s):  
Bond Strength ◽  
Statistical Significance ◽  
Testing Machine ◽  
In Vitro Study ◽  
Resin Cement ◽  
Vitro Study ◽  
Endodontically Treated Teeth ◽  
Root Dentin ◽  
Push Out

OBJECTIVE: The aim of this in vitro study was to assess the effect of obturation technique and cementation timings on the bonding of fibre-reinforced posts to the root canal walls. METHODS: Twenty extracted teeth were randomly allocated to two groups according to the obturation technique and cementation timing. Central incisors with single canals were used after being decoronated. Every extracted tooth of the {vertical compaction group} (VC) group (n = 10) had been obturated using the {E & Q plus obturation system} with posts cemented in the same day; The other (CO) conventional group (n = 10) teeth were obturated using the conventional lateral compaction technique and posts cemented after one week. “SF“ Fiber posts were used after bonding and cementation using Rely X ARC resin cement with all the endodontically treated teeth. The push-out test was performed in a universal testing machine. Data were analysed by 2 way analysis of variance with Statistical significance was set to 0.05. RESULTS: Heat softened gutta percha group showed more push out the bond strength of the bonded posts than the conventional obturation group (p < 0.05). In the middle region, there was no statistical significance between the two groups while there was significance in the coronal and apical thirds. CONCLUSION: The vertical compaction technique and early cementation improved the bond strength of the resin posts in comparison to the conventional obturation technique with late cementation.

Sign in / Sign up

Export Citation Format

Share Document