In vitro removal of anti-infective agents by a novel cytokine adsorbent system

2018 ◽  
Vol 42 (2) ◽  
pp. 57-64 ◽  
Author(s):  
Christina König ◽  
Anka C Röhr ◽  
Otto R Frey ◽  
Alexander Brinkmann ◽  
Jason A Roberts ◽  
...  
Keyword(s):  
Renal Replacement Therapy ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Normal Saline ◽  
Human Albumin ◽  
Adsorptive Capacity ◽  
Therapeutic Drug ◽  
Rapid Decline

Objectives: The aim of this study is to describe the in vitro adsorption of anti-infective drugs onto an extracorporeal cytokine adsorber. Methods: Various anti-infective drugs (β-lactams, quinolones, aminoglycosides, glycopeptides, azole antimycotics) were prepared in normal saline 0.9% and human albumin 5%, and pumped through a cytokine cartridge (CytoSorb®; CytoSorbents Corporation, Monmouth Junction, NJ, USA) at a flow rate of 1.2 L/h for 1.5 h. In addition, meropenem and ciprofloxacin were dissolved in reconstituted blood and run through a CytoSorb cartridge, which was integrated into a continuous renal replacement therapy circuit with a flow rate of 2 L/h for 18 h. Samples from the solution, pre- and post-filter, were quantified by high-performance liquid chromatography with ultraviolet detection and fluorescence polarisation immunoassay. Results: Observed mean clearance of the drugs in normal saline was 1.22 ± 0.07 L/h. In human albumin, clearance was 1.29 ± 0.08 L/h. In reconstituted blood, clearance of meropenem decreased from 5.4 to 1.4 L/h and for ciprofloxacin from 6.3 to 4.3 L/h within the first 1.5 h because of early drug adsorption. Continuous renal replacement therapy clearance measured without CytoSorb was stable at 2 and 1.7 L/h, respectively. Approximately 400 mg of meropenem and 300 mg of ciprofloxacin had been adsorbed by CytoSorb, suggesting that these amounts are the maximum adsorptive capacity for these drugs. Conclusion: In these settings, all tested drugs were adsorbed by the cartridge in relevant amounts. The identified maximum adsorptive capacity and the rapid decline in concentration during the first 1.5 h of CytoSorb use suggest that the administration of an additional dose within the first hours of CytoSorb treatment may be reasonable. In addition, early therapeutic drug monitoring should be considered.

scholarly journals Pharmacokinetics and dialytic clearance of apixaban during in vitro continuous renal replacement therapy

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
Lauren Andrews ◽  
Scott Benken ◽  
Xing Tan ◽  
Eric Wenzler
Keyword(s):  
Renal Replacement Therapy ◽  
Linear Regression ◽  
Protein Binding ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Systemic Exposure ◽  
Flow Rates ◽  
Filter Type

Abstract Background To evaluate the transmembrane clearance (CLTM) of apixaban during modeled in vitro continuous renal replacement therapy (CRRT), assess protein binding and circuit adsorption, and provide initial dosing recommendations. Methods Apixaban was added to the CRRT circuit and serial pre-filter bovine blood samples were collected along with post-filter blood and effluent samples. All experiments were performed in duplicate using continuous veno-venous hemofiltration (CVVH) and hemodialysis (CVVHD) modes, with varying filter types, flow rates, and point of CVVH replacement fluid dilution. Concentrations of apixaban and urea were quantified via liquid chromatography-tandem mass spectrometry. Plasma pharmacokinetic parameters for apixaban were estimated via noncompartmental analysis. CLTM was calculated via the estimated area under the curve (AUC) and by the product of the sieving/saturation coefficient (SC/SA) and flow rate. Two and three-way analysis of variance (ANOVA) models were built to assess the effects of mode, filter type, flow rate, and point of dilution on CLTM by each method. Optimal doses were suggested by matching the AUC observed in vitro to the systemic exposure demonstrated in Phase 2/3 studies of apixaban. Linear regression was utilized to provide dosing estimations for flow rates from 0.5–5 L/h. Results Mean adsorption to the HF1400 and M150 filters differed significantly at 38 and 13%, respectively, while mean (± standard deviation, SD) percent protein binding was 70.81 ± 0.01%. Effect of CVVH point of dilution did not differ across filter types, although CLTM was consistently significantly higher during CRRT with the HF1400 filter compared to the M150. The three-way ANOVA demonstrated improved fit when CLTM values calculated by AUC were used (adjusted R2 0.87 vs. 0.52), and therefore, these values were used to generate optimal dosing recommendations. Linear regression revealed significant effects of filter type and flow rate on CLTM by AUC, suggesting doses of 2.5–7.5 mg twice daily (BID) may be needed for flow rates ranging from 0.5–5 L/h, respectively. Conclusion For CRRT flow rates most commonly employed in clinical practice, the standard labeled 5 mg BID dose of apixaban is predicted to achieve target systemic exposure thresholds. The safety and efficacy of these proposed dosing regimens warrants further investigation in clinical studies.

scholarly journals Pharmacokinetics and Dialytic Clearance of Apixaban During In Vitro Continuous Renal Replacement Therapy

2020 ◽  
Author(s):  
Lauren Andrews ◽  
Scott Benken ◽  
Xing Tan ◽  
Eric Wenzler
Keyword(s):  
Renal Replacement Therapy ◽  
Linear Regression ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Systemic Exposure ◽  
Flow Rates ◽  
Filter Type ◽  
Post Filter

Abstract Objective: To evaluate the transmembrane clearance (CLTM) of apixaban during modeled in vitro continuous renal replacement therapy (CRRT), assess protein binding and circuit adsorption, and provide initial dosing recommendations. Design: In vitro pharmacokinetic (PK) study.Setting: University research laboratory.Subjects: Not applicable. Interventions: Apixaban was added to the CRRT circuit and serial, undiluted pre-filter bovine blood samples were collected along with analogous post-filter blood and effluent samples. All experiments were performed in duplicate using continuous veno-venous hemofiltration (CVVH) and hemodialysis (CVVHD) modes, with varying filter types (M150 and HF1400), flow rates (2 and 4 L/h), and point of CVVH replacement fluid dilution (pre, post, and pre/post filter). Concentrations of apixaban and urea were quantified via liquid chromatography-tandem mass spectrometry. Plasma PK parameters for apixaban were estimated via noncompartmental analysis in WinNonlin. CLTM was calculated via the estimated area under the curve (AUC) and by the product of the sieving/saturation coefficient (SC/SA) and flow rate. Two and three-way ANOVA models were built to assess the effects of mode, filter type, flow rate, and point of dilution on CLTM by each method. Optimal doses were suggested by matching the AUC observed in vitro to the systemic exposure demonstrated in Phase 2/3 studies of apixaban. Linear regression was then utilized to provide dosing estimations for flow rates from 0.5-5 L/h. Measurements and Main Results: Mean adsorption to the HF1400 and M150 filters differed significantly at 38% and 13%, respectively, while mean (±SD) percent protein binding was 70.81±0.01%. Effect of CVVH point of replacement fluid dilution did not differ across filter types, although CLTM was consistently significantly higher during CRRT with the HF1400 filter compared to the M150. The three-way ANOVA demonstrated improved fit when CLTM values calculated by AUC were used (adjusted R2 0.87 vs. 0.52), and therefore, these values were used to generate optimal dosing recommendations. Linear regression revealed significant effects of filter type and flow rate on CLTM by AUC, suggesting doses of 5-10 mg BID may be needed for flow rates ranging from 0.5-5 L/h respectively. Conclusion: CLTM of apixaban during CRRT resulted in estimated dosing recommendations ranging from 5 mg BID for flow rates ≤3 L/h up to 7.5-10 mg BID for rates >3 L/h, depending on filter type, in order to match target systemic exposure thresholds. The safety and efficacy of these proposed dosing regimens warrants further investigation in clinical studies.

scholarly journals Pharmacokinetics and Dialytic Clearance of Apixaban During In Vitro Continuous Renal Replacement Therapy

2020 ◽  
Author(s):  
Lauren Andrews ◽  
Scott Benken ◽  
Xing Tan ◽  
Eric Wenzler
Keyword(s):  
Renal Replacement Therapy ◽  
Linear Regression ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Systemic Exposure ◽  
Flow Rates ◽  
Filter Type ◽  
Post Filter

Abstract Objective: To evaluate the transmembrane clearance (CLTM) of apixaban during modeled in vitro continuous renal replacement therapy (CRRT), assess protein binding and circuit adsorption, and provide initial dosing recommendations. Design: In vitro pharmacokinetic (PK) study.Setting: University research laboratory.Subjects: Not applicable. Interventions: Apixaban was added to the CRRT circuit and serial pre-filter bovine blood samples were collected along with analogous post-filter blood and effluent samples. All experiments were performed in duplicate using continuous veno-venous hemofiltration (CVVH) and hemodialysis (CVVHD) modes, with varying filter types (M150 and HF1400), flow rates (2 and 4 L/h), and point of CVVH replacement fluid dilution (pre, post, and pre/post filter). Concentrations of apixaban and urea were quantified via liquid chromatography-tandem mass spectrometry. Plasma PK parameters for apixaban were estimated via noncompartmental analysis in WinNonlin. CLTM was calculated via the estimated area under the curve (AUC) and by the product of the sieving/saturation coefficient (SC/SA) and flow rate. Two and three-way ANOVA models were built to assess the effects of mode, filter type, flow rate, and point of dilution on CLTM by each method. Optimal doses were suggested by matching the AUC observed in vitro to the systemic exposure demonstrated in Phase 2/3 studies of apixaban. Linear regression was then utilized to provide dosing estimations for flow rates from 0.5-5 L/h. Measurements and Main Results: Mean adsorption to the HF1400 and M150 filters differed significantly at 38% and 13%, respectively, while mean (±SD) percent protein binding was 70.81±0.01%. Effect of CVVH point of replacement fluid dilution did not differ across filter types, although CLTM was consistently significantly higher during CRRT with the HF1400 filter compared to the M150. The three-way ANOVA demonstrated improved fit when CLTM values calculated by AUC were used (adjusted R2 0.87 vs. 0.52), and therefore, these values were used to generate optimal dosing recommendations. Linear regression revealed significant effects of filter type and flow rate on CLTM by AUC, suggesting doses of 2.5-7.5 mg BID may be needed for flow rates ranging from 0.5-5 L/h, respectively. Conclusion: For CRRT flow rates most commonly employed in clinical practice, the standard labeled 5 mg BID dose of apixaban is predicted to achieve target systemic exposure thresholds. The safety and efficacy of these proposed dosing regimens warrants further investigation in clinical studies.

Lacosamide Pharmacokinetics in a Critically Ill Patient During Continuous Renal Replacement Therapy

2018 ◽  
Vol 33 (3) ◽  
pp. 395-398 ◽  
Author(s):  
Patrick M. Wieruszewski ◽  
Arnaldo Lopez-Ruiz ◽  
Robert C. Albright ◽  
Jennifer E. Fugate ◽  
Erin Frazee Barreto
Keyword(s):  
Renal Replacement Therapy ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Critically Ill ◽  
Drug Exposure ◽  
Critically Ill Patient ◽  
Therapeutic Drug ◽  
Intermittent Hemodialysis ◽  
Pharmacokinetic Studies ◽  
Extracorporeal Removal

The objective of this study is to describe the pharmacokinetics of lacosamide in a critically ill adult during continuous venovenous hemofiltration (CVVH). A 78-year-old male developed sepsis and acute kidney injury following cardiac surgery. He was initially treated with intermittent hemodialysis but developed nonconvulsive status epilepticus at the end of the first session and was subsequently initiated on CVVH. In addition to lorazepam boluses, levetiracetam, and midazolam infusion, he was loaded with lacosamide 400 mg intravenously and started on 200 mg intravenously twice daily as maintenance therapy. Noncompartmental modeling of lacosamide pharmacokinetics revealed significant extracorporeal removal, a volume of distribution of 0.69 L/kg, elimination half-life of 13.6 hours, and peak and trough concentrations of 7.4 and 3.7 mg/L, respectively (goal trough, 5-10 mg/L). We found significant extracorporeal removal of serum lacosamide during CVVH, which was higher than previously reported. This led to subtherapeutic concentrations and decreased overall antiepileptic drug exposure. The relationship between serum lacosamide concentrations and clinical efficacy is not well understood; thus, therapeutic drug monitoring is not routinely recommended. Yet, we demonstrated that measuring serum lacosamide concentrations in the critically ill population during continuous renal replacement therapy may be useful to individualize dosing programs. Further pharmacokinetic studies of lacosamide may be necessary to generate widespread dosing recommendations.

scholarly journals In vivo / in vitro Correlation of Pharmacokinetics of Gentamicin, Vancomycin, Teicoplanin and Doripenem in a Bovine Blood Hemodialysis Model

2021 ◽  
Vol 12 ◽  
Author(s):  
M G Vossen ◽  
S Pferschy ◽  
C Milacek ◽  
M Haidinger ◽  
Mario Karolyi ◽  
...  
Keyword(s):  
Blood Flow ◽  
Renal Replacement Therapy ◽  
Protein Binding ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Blood Flow Rate ◽  
Bovine Blood ◽  
Flow Rates ◽  
Dialysate Flow Rate

Background: Elimination of a drug during renal replacement therapy is not only dependent on flow rates, molecular size and protein binding, but is often influenced by difficult to predict drug membrane interactions. In vitro models allow for extensive profiling of drug clearance using a wide array of hemofilters and flow rates. We present a bovine blood based in vitro pharmacokinetic model for intermittent renal replacement therapy.Methods: Four different drugs were analyzed: gentamicin, doripenem, vancomicin and teicoplanin. The investigated drug was added to a bovine blood reservoir connected to a hemodialysis circuit. In total seven hemofilter models were analyzed using commonly employed flow rates. Pre-filter, post-filter and dialysate samples were drawn, plasmaseparated and analyzed using turbidimetric assays or HPLC. Protein binding of doripenem and vancomycin was measured in bovine plasma and compared to previously published values for human plasma.Results: Clearance values were heavily impacted by choice of membrane material and surface as well as by dialysis parameters such as blood flow rate. Gentamicin clearance ranged from a minimum of 90.12 ml/min in a Baxter CAHP-170 diacetate hemofilter up to a maximum of 187.90 ml/min in a Fresenius medical company Fx80 polysulfone model (blood flow rate 400 ml/min, dialysate flow rate 800 ml/min). Clearance of Gentamicin vs Vancomicin over the F80s hemofilter model using the same flow rates was 137.62 mL vs 103.25 ml/min. Doripenem clearance with the Fx80 was 141.25 ml/min.Conclusion: Clearance values corresponded very well to previously published data from clinical pharmacokinetic trials. In conjunction with in silico pharmacometric models. This model will allow precise dosing recommendations without the need of large scale clinical trials.

Elimination of fluconazole during continuous renal replacement therapy. An in vitro assessment

2020 ◽  
pp. 039139882097614
Author(s):  
Frédéric J Baud ◽  
Vincent Jullien ◽  
Tarik Abarou ◽  
Benoît Pilmis ◽  
Jean-Herlé Raphalen ◽  
...  
Keyword(s):  
Renal Replacement Therapy ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Central Compartment ◽  
Sieving Coefficient ◽  
Continuous Filtration ◽  
In Vitro Assessment ◽  
The Mean ◽  
Made In

Introduction: Continuous renal replacement therapy (CRRT) efficiently eliminates fluconazole. However, the routes of elimination were not clarified. Adsorption of fluconazole by filters is a pending question. We studied the elimination of fluconazole in a model mimicking a session of CRRT in humans using the NeckEpur® model. Two filters were studied. Methods: The AV1000®-polysulfone filter with the Multifiltrate Pro. Fresenius and the ST150®-polyacrylonitrile filter with the Prismaflex. Baxter-Gambro were studied. Continuous filtration used a flowrate of 2.5 L/h in post-dilution only. Session were made in duplicate. Routes of elimination were assessed using the NeckEpur® model. Results: The mean measured initial fluconazole concentration (mean ± SD) for the four sessions in the central compartment (CC) was 14.9 ± 0.2 mg/L. The amount eliminated from the CC at the end of 6 h-session at a 2.5 L/h filtration flowrate for the AV1000®-polysulfone and the ST150®-polyacrylonitrile filters were 90%–93% and 96%–94%, respectively; the clearances from the central compartment (CC) were 2.5–2.6 and 2.4–2.3 L/h, respectively. The means of the instantaneous sieving coefficient were 0.94%–0.91% and 0.99%–0.91%, respectively. The percentages of the amount eliminated from the CC by filtration/adsorption were 100/0%–95/5% and 100/0%–100/0%, respectively. Conclusion: Neither the ST150®-polyacrylonitrile nor the AV1000®-polysulfone filters result in any significant adsorption of fluconazole.

scholarly journals Faster Blood Flow Rate Does Not Improve Circuit Life in Continuous Renal Replacement Therapy

2017 ◽  
Vol 45 (10) ◽  
pp. e1018-e1025 ◽  
Author(s):  
Nigel Fealy ◽  
Leanne Aitken ◽  
Eugene du Toit ◽  
Serigne Lo ◽  
Ian Baldwin
Keyword(s):  
Blood Flow ◽  
Renal Replacement Therapy ◽  
Continuous Renal Replacement Therapy ◽  
Replacement Therapy ◽  
Flow Rate ◽  
Blood Flow Rate
Sign in / Sign up

Export Citation Format

Share Document