Dynamic cutting force prediction for micro end milling considering tool vibrations and run-out

2018 ◽  
Vol 233 (7) ◽  
pp. 2248-2261 ◽  
Author(s):  
Xuewei Zhang ◽  
Tianbiao Yu ◽  
Wanshan Wang
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Chip Thickness ◽  
Milling Process ◽  
Force Model ◽  
Dynamic Cutting Force ◽  
Micro End Milling ◽  
Tool Vibrations ◽  
End Milling Process

An accurate prediction of cutting forces in the micro end milling, which is affected by many factors, is the basis for increasing the machining productivity and selecting optimal cutting parameters. This paper develops a dynamic cutting force model in the micro end milling taking into account tool vibrations and run-out. The influence of tool run-out is integrated with the trochoidal trajectory of tooth and the size effect of cutting edge radius into the static undeformed chip thickness. Meanwhile, the real-time tool vibrations are obtained from differential motion equations with the measured modal parameters, in which the process damping effect is superposed as feedback on the undeformed chip thickness. The proposed dynamic cutting force model has been experimentally validated in the micro end milling process of the Al6061 workpiece. The tool run-out parameters and cutting forces coefficients can be identified on the basis of the measured cutting forces. Compared with the traditional model without tool vibrations and run-out, the predicted and measured cutting forces in the micro end milling process show closer agreement when considering tool vibrations and run-out.

A Mechanistic Cutting Force Model for 3D Ball-end Milling

2000 ◽  
Vol 123 (1) ◽  
pp. 23-29 ◽  
Author(s):  
Hsi-Yung Feng ◽  
Ning Su
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Chip Thickness ◽  
Milling Process ◽  
Force Model ◽  
Cutting Force Model ◽  
Ball End Milling ◽  
End Milling Process ◽  
Force Relationship

This paper presents an improved mechanistic cutting force model for the ball-end milling process. The objective is to accurately model the cutting forces for nonhorizontal and cross-feed cutter movements in 3D finishing ball-end milling. Main features of the model include: (1) a robust cut geometry identification method to establish the complicated engaged area on the cutter; (2) a generalized algorithm to determine the undeformed chip thickness for each engaged cutting edge element; and (3) a comprehensive empirical chip-force relationship to characterize nonhorizontal cutting mechanics. Experimental results have shown that the present model gives excellent predictions of cutting forces in 3D ball-end milling.

An Experimental Investigation of Cutting Forces in Micro End-Milling Process

2016 ◽  
Vol 693 ◽  
pp. 710-717
Author(s):  
Yan Jie Yuan ◽  
Xiu Bing Jing ◽  
Huai Zhong Li ◽  
Jun Wang
Keyword(s):  
Cutting Forces ◽  
End Milling ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Milling Process ◽  
Resultant Force ◽  
Feed Force ◽  
Micro End Milling ◽  
End Milling Process ◽  
Shear Energy

This paper presents an experimental study of cutting forces during micro end-milling of brass. The influences of cutting speed and feed per tooth on cutting forces have been researched. The results show that the resultant force Fr and feed force Fx significantly increase with increasing the feed per tooth. The resultant force Fr, feed force Fxand normal force Fy increase with increasing cutting speed. The specific shear energy is also investigated. It is observed that the specific shear energy increases greatly with decreasing the feed per tooth when the feed per tooth is less than minimum chip thickness.

An improved dynamic cutting force model for end-milling process

2004 ◽  
Vol 148 (3) ◽  
pp. 317-327 ◽  
Author(s):  
Shih-Ming Wang ◽  
Chu-Hsiang Chiou ◽  
Yuan-Ming Cheng
Keyword(s):  
Cutting Force ◽  
End Milling ◽  
Milling Process ◽  
Force Model ◽  
Cutting Force Model ◽  
Dynamic Cutting Force ◽  
End Milling Process

A Mechanistic Model of Cutting Forces in Micro-End-Milling With Cutting-Condition-Independent Cutting Force Coefficients

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Han Ul Lee ◽  
Dong-Woo Cho ◽  
Kornel F. Ehmann
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Cutting Conditions ◽  
Thickness Effect ◽  
Force Model ◽  
Cutting Force Coefficients ◽  
Force Coefficients ◽  
Micro End Milling ◽  
Cutting Mechanisms

Complex three-dimensional miniature components are needed in a wide range of industrial applications from aerospace to biomedicine. Such products can be effectively produced by micro-end-milling processes that are capable of accurately producing high aspect ratio features and parts. This paper presents a mechanistic cutting force model for the precise prediction of the cutting forces in micro-end-milling under various cutting conditions. In order to account for the actual physical phenomena at the edge of the tool, the components of the cutting force vector are determined based on the newly introduced concept of the partial effective rake angle. The proposed model also uses instantaneous cutting force coefficients that are independent of the end-milling cutting conditions. These cutting force coefficients, determined from measured cutting forces, reflect the influence of the majority of cutting mechanisms involved in micro-end-milling including the minimum chip-thickness effect. The comparison of the predicted and measured cutting forces has shown that the proposed method provides very accurate results.

Cutting Force Prediction for Generalized Cornering Milling Process

2011 ◽  
Vol 188 ◽  
pp. 404-409 ◽  
Author(s):  
Xue Yan ◽  
Hua Tao ◽  
D.H. Zhang ◽  
B.H. Wu
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Milling Process ◽  
Force Model ◽  
Cutting Force Model ◽  
Cutting Force Prediction ◽  
Geometric Relationship ◽  
The Mathematical Model ◽  
Good Agreement

A developed method to predict the cutting forces in end milling of generalized corners is proposed in this paper. The cornering milling process is divided into a series of cutting segments with different cutting states. The mathematical model of the geometric relationship between cutter and the corner profile is established for each segment. Cutting forces is predicted by introducing the classical cutting force model. The computational results of cutting forces are in good agreement with experimental data.

Convolution Analysis of Milling Force Pulsation

1994 ◽  
Vol 116 (1) ◽  
pp. 17-25 ◽  
Author(s):  
J.-J. Junz Wang ◽  
S. Y. Liang ◽  
W. J. Book
Keyword(s):  
Cutting Force ◽  
Density Function ◽  
Cutting Forces ◽  
End Milling ◽  
Chip Thickness ◽  
Closed Form Expression ◽  
Thickness Variation ◽  
Depth Of Cut ◽  
Force Model ◽  
Frequency Multiplication

This paper presents the establishment of a closed form expression for the dynamic forces as explicit functions of cutting parameters and tool/workpiece geometry in milling processes. Based on the existing local cutting force model, the generation of total cutting forces is formulated as the angular domain convolution of three cutting process component functions, namely the elementary cutting function, the chip width density function, and the tooth sequence function. The elemental cutting force function is related to the chip formation process in an elemental cutting area and it is characterized by the chip thickness variation, and radial cutting configuration. The chip width density function defines the chip width per unit cutter rotation along a cutter flute within the range of axial depth of cut. The tooth sequence function represents the spacing between flutes as well as their cutting sequence as the cutter rotates. The analysis of cutting forces is extended into the Fourier domain by taking the frequency multiplication of the transforms of the three component functions. Fourier series coefficients of the cutting forces are shown to be explicit algebraic functions of various tool parameters and cutting conditions. Numerical simulation results are presented in the frequency domain to illustrate the effects of various process parameters. A series of end milling experiments are performed and their results discussed to validate the analytical model.

Sign in / Sign up

Export Citation Format

Share Document