Investigation of planing craft maneuverability using full-scale tests

2021 ◽  
pp. 147509022110303
Author(s):  
Kazem Sadati ◽  
Hamid Zeraatgar ◽  
Aliasghar Moghaddas
Keyword(s):  
Full Scale ◽  
Performance Characteristics ◽  
Forward Speed ◽  
Speed Reduction ◽  
Planing Craft ◽  
Full Scale Tests ◽  
Turning Maneuver

Maneuverability of planing craft is a complicated hydrodynamic subject that needs more studies to comprehend its characteristics. Planing craft drivers follow a common practice for maneuver of the craft that is fundamentally different from ship’s standards. In situ full-scale tests are normally necessary to understand the maneuverability characteristics of planing craft. In this paper, a study has been conducted to illustrate maneuverability characteristics of planing craft by full-scale tests. Accelerating and turning maneuver tests are conducted on two cases at different forward speeds and rudder angles. In each test, dynamic trim, trajectory, speed, roll of the craft are recorded. The tests are performed in planing mode, semi-planing mode, and transition between planing mode to semi-planing mode to study the effects of the craft forward speed and consequently running attitude on the maneuverability. Analysis of the data reveals that the Steady Turning Diameter (STD) of the planing craft may be as large as 40 L, while it rarely goes beyond 5 L for ships. Results also show that a turning maneuver starting at planing mode might end in semi-planing mode. This transition can remarkably improve the performance characteristics of the planing craft’s maneuverability. Therefore, an alternative practice is proposed instead of the classic turning maneuver. In this practice, the craft traveling in the planing mode is transitioned to the semi-planing mode by forward speed reduction first, and then the turning maneuver is executed.

A Case Study of Dynamic Instability in a Planing Hull

1987 ◽  
Vol 24 (02) ◽  
pp. 143-163
Author(s):  
Louis Codega ◽  
James Lewis
Keyword(s):  
High Speed ◽  
Dynamic Instability ◽  
Test Procedure ◽  
Large Angle ◽  
Model Tests ◽  
Full Scale ◽  
Planing Craft ◽  
Normal Operating ◽  
Full Scale Tests

Soon after introduction into service, a class of high-speed planing boats began to exhibit a dynamic instability that manifested itself in the craft trimming by the bow, rolling to a large angle of heel to port, and broaching violently to starboard, all within five seconds. This behavior, which occurred within the craft's normal operating envelope, could not be attributed to operator causes and resulted in unacceptable operating restrictions being placed on the craft. After a number of unsuccessful attempts to remedy the problem, an investigation to research possible causes was undertaken. Concurrently, a test boat was instrumented to quantify its behavior and, most importantly, to record the hydrodynamic bottom pressures acting while this phenomenon occurs. The craft is described and initial attempts at solving the problem are outlined. The results of research on this type of phenomena in both planing craft and flying boats are presented. The instrumentation system, complex for this size craft, is detailed and the test procedure described. The results of the full-scale tests are given, along with qualitative comparisons with other craft that display a similar problem and model tests that would indicate the possibility of such instabilities. The cause of the instability is described and recommendations are made to avoid similar problems in future craft.

scholarly journals Upscaling THM modeling from small-scale to full-scale in-situ experiments in the Callovo-Oxfordian claystone

2021 ◽  
Vol 144 ◽  
pp. 104582
Author(s):  
D.M. Seyedi ◽  
C. Plúa ◽  
M. Vitel ◽  
G. Armand ◽  
J. Rutqvist ◽  
...  
Keyword(s):  
Full Scale ◽  
Small Scale ◽  
In Situ Experiments

Full-scale tests of the trash racks of the Kapchagai hydroelectric station

1984 ◽  
Vol 18 (4) ◽  
pp. 166-170
Author(s):  
A. L. Rakhmanova ◽  
I. O. Rybak
Keyword(s):  
Hydroelectric Station ◽  
Full Scale ◽  
Full Scale Tests

Coupled Thermo-Hydro-Geochemical Models of Engineered Barrier Systems: The Febex Project

2000 ◽  
Vol 663 ◽  
Author(s):  
J. Samper ◽  
R. Juncosa ◽  
V. Navarro ◽  
J. Delgado ◽  
L. Montenegro ◽  
...  
Keyword(s):  
Large Scale ◽  
Reference Model ◽  
Numerical Models ◽  
Full Scale ◽  
Small Scale ◽  
Model Parameters ◽  
In Situ Test ◽  
Wide Range ◽  
Engineered Barrier

ABSTRACTFEBEX (Full-scale Engineered Barrier EXperiment) is a demonstration and research project dealing with the bentonite engineered barrier designed for sealing and containment of waste in a high level radioactive waste repository (HLWR). It includes two main experiments: an situ full-scale test performed at Grimsel (GTS) and a mock-up test operating since February 1997 at CIEMAT facilities in Madrid (Spain) [1,2,3]. One of the objectives of FEBEX is the development and testing of conceptual and numerical models for the thermal, hydrodynamic, and geochemical (THG) processes expected to take place in engineered clay barriers. A significant improvement in coupled THG modeling of the clay barrier has been achieved both in terms of a better understanding of THG processes and more sophisticated THG computer codes. The ability of these models to reproduce the observed THG patterns in a wide range of THG conditions enhances the confidence in their prediction capabilities. Numerical THG models of heating and hydration experiments performed on small-scale lab cells provide excellent results for temperatures, water inflow and final water content in the cells [3]. Calculated concentrations at the end of the experiments reproduce most of the patterns of measured data. In general, the fit of concentrations of dissolved species is better than that of exchanged cations. These models were later used to simulate the evolution of the large-scale experiments (in situ and mock-up). Some thermo-hydrodynamic hypotheses and bentonite parameters were slightly revised during TH calibration of the mock-up test. The results of the reference model reproduce simultaneously the observed water inflows and bentonite temperatures and relative humidities. Although the model is highly sensitive to one-at-a-time variations in model parameters, the possibility of parameter combinations leading to similar fits cannot be precluded. The TH model of the “in situ” test is based on the same bentonite TH parameters and assumptions as for the “mock-up” test. Granite parameters were slightly modified during the calibration process in order to reproduce the observed thermal and hydrodynamic evolution. The reference model captures properly relative humidities and temperatures in the bentonite [3]. It also reproduces the observed spatial distribution of water pressures and temperatures in the granite. Once calibrated the TH aspects of the model, predictions of the THG evolution of both tests were performed. Data from the dismantling of the in situ test, which is planned for the summer of 2001, will provide a unique opportunity to test and validate current THG models of the EBS.

Sign in / Sign up

Export Citation Format

Share Document