Finite element simulations and experimental studies on inhomogeneous metal flow in aluminium extrusions with three-dimensional complex geometries

2002 ◽  
Vol 18 (11) ◽  
pp. 1377-1381 ◽  
Author(s):  
Q. Li ◽  
C. Smith ◽  
C. Harris ◽  
M. R. Jolly
Keyword(s):  
Finite Element ◽  
Metal Flow ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Finite Element Simulations ◽  
Complex Geometries

A Biomechanical Model of Lumbar Spine

2000 ◽  
Author(s):  
Subramanya Uppala ◽  
Robert X. Gao ◽  
Scott Cowan ◽  
K. Francis Lee
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Fe Model ◽  
Flexion Extension ◽  
Cortical Shell ◽  
Three Dimensional Finite Element

Abstract The strength and stability of the lumbar spine are determined not only by the bone and muscles, but also by the visco-elastic structures and the interplay between the different components of the spine, such as ligaments, capsules, annulus fibrosis, and articular cartilage. In this paper we present a non-linear three-dimensional Finite Element model of the lumbar spine. Specifically, a three-dimensional FE model of the L4-5 one-motion segment/2 vertebrae was developed. The cortical shell and the cancellous bone of the vertebral body were modeled as 3D isoparametric eight-nodal elements. Finite element models of spinal injuries with fixation devices are also developed. The deformations across the different sections of the spine are observed under the application of axial compression, flexion/extension, and lateral bending. The developed FE models provided input to both the fixture design and experimental studies.

Finite Element Modeling of Hard Roller Burnishing: An Analysis on the Effects of Process Parameters Upon Surface Finish and Residual Stresses

2007 ◽  
Vol 129 (4) ◽  
pp. 705-716 ◽  
Author(s):  
Partchapol Sartkulvanich ◽  
Taylan Altan ◽  
Francisco Jasso ◽  
Ciro Rodriguez
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Process Parameters ◽  
Surface Finish ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Cost Effective ◽  
Machined Surface ◽  
Fem Model ◽  
Roller Burnishing

Hard roller burnishing is a cost-effective finishing and surface enhancement process where a ceramic ball rolls on the machined surface to flatten the roughness peaks. The ball is supported and lubricated by hydrostatic fluid in a special tool holder. The process not only improves surface finish but also imposes favorable compressive residual stresses in functional surfaces, which can lead to long fatigue life. Most research in the past focused on experimental studies. There is still a special need for a reliable finite element method (FEM) model that provides a fundamental understanding of the process mechanics. In this study, two-dimensional (2D) and three-dimensional FEM models for hard roller burnishing were established. The developed 2D FEM model was used to study the effects of process parameters (i.e., burnishing pressure, feed rate) on surface finish and residual stresses. The simulation results were evaluated and compared to the experimental data. Results show that the established FEM model could predict the residual stresses and provided useful information for the effect of process parameters. Both FEM and experiments show that burnishing pressure is the most influence, where high burnishing pressure produces less roughness and more compressive residual stress at the surface.

scholarly journals Finite Element Analysis of Turbulent Flows Using LES and Dynamic Subgrid-Scale Models in Complex Geometries

2011 ◽  
Vol 2011 ◽  
pp. 1-20 ◽  
Author(s):  
Wang Wenquan ◽  
Zhang Lixiang ◽  
Yan Yan ◽  
Guo Yakun
Keyword(s):  
Finite Element ◽  
Turbulent Flow ◽  
Turbulent Flows ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Turbulent Channel Flow ◽  
Francis Turbine ◽  
Complex Geometries ◽  
Subgrid Scale ◽  
Element Analysis

An innovative computational model is presented for the large eddy simulation (LES) of multidimensional unsteady turbulent flow problems in complex geometries. The main objectives of this research are to know more about the structure of turbulent flows, to identify their three-dimensional characteristic, and to study physical effects due to complex fluid flow. The filtered Navier-Stokes equations are used to simulate large scales; however, they are supplemented by dynamic subgrid-scale (DSGS) models to simulate the energy transfer from large scales toward subgrid-scales, where this energy will be dissipated by molecular viscosity. Based on the Taylor-Galerkin schemes for the convection-diffusion problems, this model is implemented in a three-dimensional finite element code using a three-step finite element method (FEM). Turbulent channel flow and flow over a backward-facing step are considered as a benchmark for validating the methodology by comparing with the direct numerical simulation (DNS) results or experimental data. Also, qualitative and quantitative aspects of three-dimensional complex turbulent flow in a strong 3D blade passage of a Francis turbine are analyzed.

Sign in / Sign up

Export Citation Format

Share Document